Enantioselective separation and dissipation of pydiflumetofen enantiomers in grape and soil by supercritical fluid chromatography–tandem mass spectrometry

Pydiflumetofen is registered in many countries and is widely used in crop production in the racemate form. However, the environmental behavior of the enantiomers has not been studied. An effective and sensitive chiral analytical method was first established for analyzing the pydiflumetofen enantiomers by supercritical fluid chromatography with tandem triple quadrupole mass spectrometry. The enantiomers could be separated and detected using the Chiralcel OD‐3 column in less than 3 min. The separation conditions were as follows: mobile phase, CO₂/methanol (80:20); flow rate, 1.0 mL/min; column temperature, 30°C, auto back‐pressure regulator pressure, 2000 psi with modified quick, easy, cheap, effective, rugged, and safe sample treatment method. The average recoveries of analytes from both matrices at three spiking levels were in the range of 84.1–103.0%. The limit of quantitation for each enantiomer was 0.005 mg/kg with a baseline resolution of approximately 1.64. The method was applied to monitor the enantioselective dissipation of pydiflumetofen in grape and soil. In grapes, (?)‐pydiflumetofen was degraded more rapidly than (+)‐pydiflumetofen. In soil, (+)‐pydiflumetofen was preferentially degraded. The data provided useful references for the risk assessment and rational use of pydiflumetofen in agriculture.     

滚滑工况弹流反常温度场的研究

研究了弹流反常温度场的形成机理及影响因素，指出入口温升是压缩功发热和逆流剪切热所致，而出口局部低温是负压缩功吸热的结果，出口温度的再次微幅上升则是压缩功消失后剪切热作用的结果．研究结果表明，入口温升随载荷的增加而增大，随卷吸速度的增加显著升高而几乎与滑滚比无关；在高速小滑滚比工况下，接触区的最高温度有可能出现在入口位置；入口温升增加了材料在工作中经受高温的次数，对其接触疲劳寿命有不利影响；在保证润滑性能的前提下，适当减少供油量可以减小逆流，从而降低入口温升。     

The pentacene films on the glass/ITO surface: structure and optical properties

Abstract

The structure, morphology and optical transmittance spectra of pentacene films on the (glass/ITO) surface were studied. The films were grown by two methods - the thermal vacuum deposition (TVD) and pulsed laser deposition (PLD). The electron diffraction pattern from thermally deposited pentacene films confirms their polycrystalline structure while the diffraction pattern of PLD-coated layers has a diffusion character. The results obtained showed that layers deposited by the TVD method has an optical spectrum that is characteristic for the pentacene film in contrary to the layers deposited by the PLD method. It is found a sensitivity of the optical transmittance of pentacene films to the ammonia action, which may be used for development the optical gas sensor.     

Sizes,Components, Crystalline Structure,and Thermal Properties of Starches from Sweet Potato Varieties Originating from Different Countries

Sweet potato is a root tuber crop and an important starch source. There are hundreds of sweet potato varieties planted widely in the world. Starches from varieties with different genotype types and originating from different countries have not been compared for their physicochemical properties. In the research, starches from 44 sweet potato varieties originating from 15 countries but planted in the same growing conditions were investigated for their physicochemical properties to reveal the similarities and differences in varieties. The results showed that the 44 starches had granule size (D[4,3]) from 8.01 to 15.30 μm. Starches had different iodine absorption properties with OD680 from 0.259 to 0.382 and OD620/550 from 1.142 to 1.237. The 44 starches had apparent amylose content from 19.2% to 29.2% and true amylose content from 14.2% to 20.2%. The starches exhibited A-, C_A-, C_C-, or C_B-type X-ray diffraction patterns. The thermograms of 44 starches exhibited one-, two-, or three-peak curves, leading to a significantly different gelatinization temperature range from 13.1 to 29.2 °C. The significantly different starch properties divide the 44 sweet potato varieties into different groups due to their different genotype backgrounds. The research offers references for the utilization of sweet potato germplasm.     

Synthesis and characterization of nanocrystalline MgAl2O4 spinel by polymerized complex method

Ultrafine MgAl₂O₄ powder has been synthesized by a polymerized complex method. Heating of a precursor solution containing citric acid (CA), ethylene glycol (EG) and Mg and Al salts with a molar ratio of Mg/Al/CA/EG=1/2/8/32 at 180°C produced a transparent polymeric gel, which have been characterized by FT-IR spectroscopy and TG/DTA. The organic fraction was removed by controlled thermal treatments (350–1200°C) whereby the bimetallic oxide was formed. XRD analysis showed the presence of MgAl₂O₄ at 600°C. TEM observation showed that the spherical nanosized powders with good uniformity was obtained. Furthermore, these powders showed excellent sinterability, relative density up to 99.8% was achieved when sintered at 1550°C for 3 h in air without any sintering additive.     

Comparative characterization of thermal isomerization rates of 6‐phenyl‐1,5‐diazabicyclo[3.1.0]hexane at convection and microwave heating

Rate constants of thermal isomerization of 6‐phenyl‐1,5‐diazabicyclo[3.1.0]hexane into 1‐(benzyl)‐4,5‐dihydro‐1H‐pyrazole at convection and microwave heating in toluene and chlorobenzene (solvents) were determined within the temperature range 90°C to 120°С. These data were used for the calculation of activation parameters of isomerization. It is shown that microwave heating increases the rate constants at the same temperature by a factor of 2 to 2.5 as compared with those using convection heating. The reason is that the effective temperature of microwave heating exceeds that of convection heating by 6°C to 9°С in toluene and by 12°C to 20°С in chlorobenzene as solvent.     

Experimental thermal performance study of natural graphite as sensible heat storage material using different heat transfer fluids

In this paper thermal performance of graphite-based sensible heat storage system with embedded helical coil in rectangular shell was studied. Plain water at four flow rates (0.25 LPM–1.0 LPM) and four inlet temperatures (60°C–90°C) was passed through the graphite bed and charging time was measured. Expanded graphite/water suspension and Al₂O₃/water nanofluid were also used to study charging behavior of graphite. Results showed that charging time of packed bed was reduced with increase in flow rate and inlet temperature of heat transfer fluid. Charging time using expanded graphite/water solution and nanofluid was 14.2% and 21.2% lesser than water.

Abbreviations: h_i: internal heat transfer coefficient (W m^?2 K^?1); HTF: Heat transfer fluid; h_o: External heat transfer coefficient (W m^?2 K^?1); LPM: liter per minute; k: thermal conductivity (W m^?1 K^?1); TSU: Thermal storage unit     

Experimental study of heat transfer characteristics in oscillating fluid flow in tube

In the present work, an experimental investigation of heat transfer enhancement parameters of the oscillating flow heat exchanger under different frequencies, tidal displacement, and heat fluxes is carried out. The effect of different parameters on experimental effective thermal conductivity and convective heat transfer coefficient in cooling region is studied using correlations given by different researchers. A correlation for experimental effective thermal conductivity in terms of S²√ω is derived based on experimental data. This correlation is useful for predicting the optimum value of S²√ω before onset of turbulence.     

采用曲率传感器测量热透镜焦距

分析了用光栅型波前曲率传感器测量热透镜焦距的基本原理,针对高功率固体激光器的工作特点,结合实验现象推导了在热透镜效应较强时热透镜焦距变化的计算公式。对半导体二极管(LD)侧面泵浦的百W级Nd:YAG激光棒在泵浦电流为15~25 A时的热透镜焦距值进行了测量,讨论了可能存在的误差。实验现象和理论分析一致,测量的热透镜焦距值与理论值符合得较好。