Sample evaporation in conventional split/splitless GC injectors. Part 3: Retaining the liquid in the vaporizing chamber

As most sample liquids tend to pass through an empty injector insert at a speed which is too high to enable complete evaporation, movement of the liquid must be arrested before it reaches the column entrance. Stopping the liquid means deposition on to a surface; this, however, is possible only after the temperature of the surface has been cooled to (or below) the boiling point of the liquid (solvent). The performance of different means of stopping the liquid has been tested visually (by the method described in Part 2). Baffles on the wall of the injector insert had hardly any effect on evaporation: the band of liquid leaving the syringe needle performed a perfect slalorn around them. The inverted cup proved more efficient, but the best performance was obtained from a light plug of glass wool: owing to its low thermal mass, the first fibers to be met by the liquid are immediately cooled to the solvent boiling point, allowing the liquid to wet it. The sample liquid is sucked up by the glass wool, from where the sample evaporates relatively slowly, often over a period of several seconds.     

Elution behavior of styrene oligomer fractions in supercritical fluid chromatography

Summary In supercritical fluid chromatography (SFC), the elution behavior of styrene oligomers in pentane depends greatly on the degree of oligomerization, n. The influence of capacity ratio, k, on the lower oligomers up to about n=11 resembles the behavior of other substrates of low molecular weight, like aromatic hydrocarbons. Thus, with pentane of 100 bar and below, minima are found in plots of k versus temperature. In contrast, the k of oligomers of higher molecular weight (n>11) increase monotonously with increasing temperature. The studies were performed using oligostyrene fractions obtained by semipreparative SFC fractionation.     

Thermal degradation kinetics of polyimide containing 2,6-benzobisoxazole units

A novel polyimide (PI) based on 2,6-bis(p-aminophenyl)-benzo[1,2-d;5,4-d′]bisoxazole has been synthesized via a conventional two-stage procedure with bis(ether anhydrides) (HQDPA). The intermediate poly(amic acid) had inherent viscosities of 1.70 dl/g and could be thermally converted into light yellow polyimide film. The resulted polyimide showed excellent thermal stability, and the glass transition temperatures (T_g) were above 283 °C, the 5% weight loss temperature of the polymer was at 572 °C in N₂. The thermal degradation of the polyimide was studied by thermogravimetric analysis (TGA) in order to determine the actual reaction mechanisms of the decomposition process. The activation energy of the solid-state process was determined using Flynn-Wall-Ozawa method, which does not require knowledge of the reaction mechanism, which resulted to be 361.36 kJ/mol. The activation energy of different mechanism models and pre-exponential factor (A) were determined by Coats-Redfern method. Compared with the value obtained from the Ozawa method, the actual reaction mechanism obeyed nucleation and growth model, Avrami-Erofeev function (A₃) with integral form g(X) = [−ln(1−X)]³.     

呋喃西林水溶液在光和热作用下的稳定性

The influence of both light and heat on the stability of nitrofurazone aqueous solution was studied. Results show that in either heating experiments or the exposure to light at high temperatures, the degradation rate obeyed zero-order kinetics. The total rate constant ktotal caused by both light and heat can be divided into two parts: ktotal =kdark klight, where kdark and klight are the degradation rate constants caused by heat and light, respectively. The klight can be expressed as klight=Alight*exp(-Ea,light/RT)*E, where E is the illuminance of light, and Alight and Ea,light both are experimental constants. The values of these kinetic parameters were determined based on the experiments in the dark and upon exposure to three different light sources. Results show that the values of Alight and Ea, light varied with the light source. To save time, labor, and drugs, exponential heating experiments were employed and compared with the isothermal experiments. Results indicated that kinetic parameters obtained by exponential heating experiments are comparable to those obtained by isothermal experiments either in the dark or upon exposure to light.     

Some Pharmaceutical Properties of a New Branched Cyclodextrin, 6-O-α-(4-O- α-D-Glucuronyl)-D-glucosylβ-cyclodextrin

Some physicochemical and biological properties of a new branched cyclodextrin, 6-O--(4-O--d-glucuronyl)-d-glucosyl--cyclodextrin GUG--CyD) were investigated. Further, theinteraction of GUG--CyD with several drugs was studied by the solubility and spectroscopic methods, and compared with those of parent -CyD and 6-O--maltosyl--CyD(₂--CyD).The hemolytic activity of GUG--CyD on rabbit erythrocytes was lower than those of -CyD and ₂--CyD. GUG--CyD and ₂--CyD showed negligible cytotoxicity on Caco-2 cells up to at least 0.1 M. The inclusion ability of GUG--CyD to neutral and acidic drugs was comparable to or slightly smaller than those of -CyD and ₂--CyD, probably because of a steric hindrance of the branched sugar. On the other hand, GUG--CyD showed greater affinity for the basic drugs, compared with -CyD and ₂--CyD, owing to the electrostatic interaction of its carboxylate anion with positive charge of basic drugs. Thus GUG--CyD may be useful as a safe solubilizing agent particularly for basic drugs.     

Temperature dependence of fractionation of hydrogen isotopes in aqueous sodium chloride solutions

The D/H ratios of hydrogen gas in equilibrium with aqueous sodium chloride solutions of 2, 4 and 6 molalities were determined within the range 10 to 95°C, using a hydrophobic platinum catalyst. With each of the different sodium chloride concentrations, the hydrogen isotope effect between the solution and pure water changes linearly with the square of the reciprocal temperature. On the basis of the results for hydrogen isotope fractionation observed in this study, and those of hydrogen isotope fractionation between pure water and vapor, it is concluded that the structure of the aqueous sodium chloride solution does not change significantly with temperature. The hydrogen isotope effect is evidently different from the results of vapor pressure isotope effects (VPIE) on sodium chloride solutions measured on separated isotopes. The difference between the present work and the VPIE studies is probably due to a non-ideal behavior in a mixture of isotopic water molecules and/or to a H₂O-D₂O disproportionation reaction in sodium chloride solutions. The distinction between the latter two mechanisms can not be differentiated at present.     

Studies on Liquid/liquid Extraction of Copper Ion with Room Temperature Ionic Liquid

Room temperature ionic liquids are regarded as “Green solvents” for their nonvolatile and thermally stable properties. They are employed to replace traditional volatile organic solvents in organic synthesis, solvent extraction, and electrochemistry. In this work, a water immiscible room temperature ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate [C₄mim][PF₆], was used as an alternative solvent for liquid/liquid extraction of copper ions. Metal chelators, including dithizone, 8‐hydroxyquinoline, and 1‐(2‐pyridylazo)‐2‐naphthol, were employed to form neutral metal‐chelate complexes with copper ions so that copper ions were extracted from aqueous solution into [C₄mim][PF₆]. The parameters that affect the extraction of copper ions with this biphasic system were investigated. The extraction behavior in this novel biphasic system is shown to be consistent with that of traditional solvents. For example, the extraction with this biphasic system is strongly pH dependent. So, the extraction efficiency of coppers ion from an aqueous phase can be manipulated by tailoring the pH value of the extraction system. Hence, the extraction, separation and preconcentraction of copper ions can be accomplished by controlling the pH value of the extraction system. It appears that the use of ionic liquid as an alternate solvent system in liquid/liquid extraction of copper ions is very promising.     

Synthesis and properties of aromatic poly(ester amide)s with pendant phosphorus groups

Two series of phosphorus‐containing aromatic poly(ester amide)s with inherent viscosities of 0.46–3.20 dL/g were prepared by low‐temperature solution polycondensation from 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl)naphthalene and 1,4‐bis(4‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl)naphthalene with various aromatic diacid chlorides. All the poly(ester amide)s were amorphous and readily soluble in many organic solvents, such as N,N‐dimethylformamide, N,N‐dimethylacetamide (DMAc), and N‐methyl‐2‐pyrrolidone (NMP). Transparent, tough, and flexible films of these polymers were cast from DMAc and NMP solutions. Their casting films had tensile strengths of 71–214 MPa, elongations to break of 5–10%, and initial moduli of 2.3–6.0 GPa. These poly(ester amide)s had glass‐transition temperatures of 209–239 °C (m‐series) and 222–267 °C (p‐series). The degradation temperatures at 10% weight loss in nitrogen for these polymers ranged from 462 to 489 °C, and the char yields at 800 °C were 55–63%. Most of the poly(ester amide)s also showed a high char yield of 35–45%, even at 800 °C under a flow of air. The limited oxygen indices of these poly(ester amide)s were 35–46. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 459–470, 2002; DOI 10.1002/pola.10129     

Synthesis and characterization of temperature‐ and pH‐sensitive hydrogels based on poly(2‐ethyl‐2‐oxazoline) and poly(D,L‐lactide)

A novel series of temperature‐ and pH‐sensitive hydrogels based on poly(2‐ethyl‐2‐oxazoline) and three‐arm poly(D,L ‐lactide) were synthesized via photocopolymerization. For the creation of polymeric networks, two types of macromers terminated with methacrylate groups were prepared: poly(2‐ethyl‐2‐oxazoline) dimethacrylate and three‐arm poly(D,L ‐lactide) trimethacrylate. The chemical structures were analyzed with ¹H NMR and Fourier transform infrared techniques. The thermal behaviors, morphologies, and swelling properties were measured for the characterization of the polymeric networks. All the poly(2‐ethyl‐2‐oxazoline)/three‐arm poly(D,L ‐lactide)hydrogels provided high water retention capacity and exhibited reversible swelling–shrinking behavior in response to temperature and pH variations. The hydrogels with higher poly(2‐ethyl‐2‐oxazoline) dimethacrylate contents were more effective in raising the swelling ratio and temperature and pH sensitivity. However, higher contents of three‐arm poly(D,L ‐lactide) trimethacrylate produced larger particles and pore sizes in the hydrogels. This study effectively proves that this unique combination of water swellability and biodegradability provides hydrogels with a much wider range of applications in biomedical fields. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1112–1121, 2002     

C→N Migrations of the ethoxycarbonyl group in reactions of ortho-substituted aryl isocyanates with the 1,3-zwitterion derived from triisopropylphosphine and ethyl 2-cyanoacrylate

The reactions of meta—para-substituted aryl isocyanates with phosphorus-containing 1,3-zwitterions, which proceed with the CN migration of the CO₂Et group to form the corresponding carbamates, were extended to ortho-substituted aryl isocyanates. The influence of the steric and electronic effects of the ortho substituents in the aromatic rings of aryl isocyanates on the ease of this rearrangement is qualitatively considered.