High-Throughput Synthesis and Characterization of Aryl Silicones by Using the Piers–Rubinsztajn Reaction

Arylsilicones are widely exploited for their thermal and optical properties. The creation of phenylsilicone elastomers with specific physical properties is typically done by a “one-off” formulation and test process. Herein, it is demonstrated that high-throughput synthesis methods can be used to rapidly prepare a series of arylsilicone elastomers and then the relative impact of different aryl groups on their physical properties is assessed. Aromatic groups were incorporated into polydimethylsiloxane (PDMS) elastomers by exploiting the relative reactivity of different functional groups in the Piers–Rubinsztajn reaction. To analyze trends in the silicone mechanical properties as a function of increasing aryl concentration—structure/property relationships—libraries of elastomers were both quickly synthesized and characterized by using high-throughput suites starting from low viscosity silicone oils/monomers in 96-well plates. Liquid handling parameters were optimized to effectively work with the silicones. Incorporating aryl instead of alkyl crosslinkers into the PDMS backbone increased the silicone elastomer modulus by approximately 50 % (at a crosslink density of 6 %); elastomers prepared with an aromatic crosslinker with three contact points led to much higher moduli compared with those with one contact point at the same crosslink density. When located at precise rather than random points on the silicone chains, diphenylsilicones had lower moduli than analogous monophenylsilicones.     

高灵敏度Si基纤毛式MEMS湍流传感器

为了满足湍流探测高灵敏度、高分辨率的要求,提出了一种新型纤毛微电子机械系统(MEMS)湍流传感器。基于MEMS技术制作了硅十字梁敏感受力结构,通过橡胶探头的受力振动传递水中的湍流信号,凭借传感器头部的导流罩来保证传感器的高分辨率探测。对MEMS湍流传感器进行理论和仿真分析,其一阶共振频率达到481.04 Hz。经过海洋环境模拟机测试实验,结果显示其在50 MPa压力下保持了完好的结构和良好的性能,验证了其水下的可靠性。在湍流实验平台进行测试,通过比较标定法得出其灵敏度为1.92×10^-4 V·m·s^2/kg,满足海洋湍流测试要求。     

Preparation of free‐standing silicone particles in aqueous heterogeneous system

To prepare cross‐linked silicone (silicone rubber) particles in an aqueous medium, we investigated two synthesis methods involving a miniemulsion system. The first method was based on cationic ring‐opening polymerization of cyclic siloxane, which is a common synthetic route for linear silicone oil and uses octamethylcyclotetrasiloxane (D₄) as the monomer and dimeric D₄ (bis‐D₄) as the cross‐linker. Although this method produces silicone particles, the particles do not remain in the particulate state after drying because of low cross‐linking density. The polymerization mechanism of this method was also investigated, which proceeds under the ring‐opening reaction of D₄ in monomer droplets and upon polycondensation of hydrolyzed D₄, which occurs in the water phase (ie, outside the monomer droplets). This mechanism implied that introducing the cross‐linking structure into particles is difficult because of the low solubility of bis‐D₄ in water. To overcome these difficulties, we demonstrated a second method of preparing silicone particles based on the thiol‐Michael addition reaction between thiol‐terminated silicone oil and triacrylate in miniemulsion systems. Transmission electron microscopy images indicated that the silicone particles obtained in the particulate state upon drying and the aggregates of these particles showed elasticity.     

Effects of graded porous structure on local strain distribution under compression in silicone rubber

Silicone rubber samples with gradually changing pore sizes within the range of 70–610 μm are produced using an improved spacer method. The samples are scanned using an X‐ray computed tomography to evaluate their graded structure as compared to uniform rubber. A compressive test reveals that graded porous silicone rubber has characteristic stress–strain curves whose slope changes within a specific strain range depending on the porous structure. Analysis results of local strain based on a digital image correlation of the graded porous silicone rubber under compression demonstrate that the characteristic stress–strain properties are caused by shifts in the main deformation region in the graded structure. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1033–1042     

Properties of Natural Rubber/Recycled Chloroprene Rubber Blend: Effects of Blend Ratio and Matrix

The present study investigated the effects of two types of natural rubber and different blend ratios on the cure, tensile properties and morphology of natural rubber/recycled chloroprene rubber blends. The blends of natural rubber/recycled chloroprene rubber were prepared by using laboratory two-roll mill. The result showed that the cure time prolonged with the addition of recycled chloroprene rubber (rCR). Comparability, natural rubber/recycled chloroprene rubber (SMR L/rCR) blendcured rapidly than epoxidized natural rubber/recycled chloroprene rubber (ENR 50/rCR) blend. The addition of rCRalso caused a decrement in the tensile strength and elongation at break for both rubber blends. The SMR L/rCR blendsshowed higher tensile strength and elongation at break compared to those of ENR 50/rCR blends at any blend ratios.     

Dynamic Rebound Behavior of Silica/Natural Rubber Composites: Fly Ash Particles and Precipitated Silica

This article investigated the elastic response of natural rubber (NR) compounds filled with silica from fly ash particles (FASi) and commercial precipitated silica (PSi), through a dynamic rebound test. The effects of silica content and initial drop‐height on the height and number of rebounds, dynamic stiffness, and the energy loss were of interest. The results suggested that the unfilled NR vulcanizates exhibited a greater elastic response than the FASi and PSi‐filled vulcanized composites. For given silica contents, the NR compounds with FASi had better elastic response than those with PSi, where the elastic response decreased with an increase in silica content. The greater the silica contents, the higher the dynamic stiffness of the composites. The initial drop‐height had no effects on the elastic response change for the unfilled NR compound, but resulted in an increase in the energy loss for the silica‐filled NR composites. The differences in the elastic responses for the NR compounds filled with silica from FASi and PSi were associated with the differences in crosslink density and the filler–filler interaction influenced by content of bis(3‐triethoxysilylpropyl) tetrasulfane (designated as Si69) used.     

Cross‐linking and properties of rubber magnetic composites cured with different curing systems

Rubber magnetic composites were prepared by incorporation of strontium ferrite into rubber compounds based on acrylonitrile butadiene rubber and ethylene propylene diene monomer rubber. The sulfur, peroxide, and mixed sulfur/peroxide curing systems were introduced as cross‐linking agents for rubber matrices. The aim was to investigate the influence of curing system composition on curing process and cross‐link density of composite materials. Then, static and dynamic mechanical properties and thermal and magnetic characteristics were investigated in relation to the cross‐link density of rubber magnetic composites and structure of the formed cross‐links. The changes of dynamical and physicomechanical properties were in close correlation with the change of cross‐link density, whereas the tensile strength of magnetic composites showed increasing trend with increasing amount of peroxide in mixed curing systems. On the other hand, thermal conductivity and magnetic characteristics were found not to be dependent on the curing system composition.     

Interfacial mechano-chemical grafting in styrene-butadiene rubber/halloysite nanotubes composites

SBR/unmodified HNT composites were prepared by open-mill mixing and vulcanization. The results showed that HNT could decrease the scorch and optimum cure time, and play a significant role in reinforcing SBR vulcanizates. Mechano-chemical grafting at the interface between HNT and SBR was investigated by using infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), solid-state ¹³C NMR spectra and bonded rubber content, etc. The results showed the shearing force during the mixing process can impel the grafting reaction of SBR onto the surfaces of HNT, which leads to interfacial chemical bonding between phenyl’s α-H of SBR and the surface groups of HNT with Si-OH or Al-OH. Thus, the mechanical properties of the composites were significantly enhanced.     

Aging properties of styrene-butadiene rubber nanocomposites filled with carbon black and rectorite

To better understand the effect of rectorite and carbon black (CB) on the aging performance of styrene-butadiene rubber (SBR), SBR/CB, SBR/CB/rectorite and SBR/rectorite nanocomposites with the same total filler loading were prepared. The microstructure of the three SBR nanocomposites was characterized by XRD, TEM and SEM. After thermal aging, oxygen-containing molecules were found to be formed in the SBR nanocomposites, as verified by FTIR analysis. The SBR/rectorite nanocomposite showed the highest aging coefficient and the lowest change rate of tensile strength and stress at 100% strain among the three SBR nanocomposites, indicating that the introduction of nano-dispersed rectorite layers can enhance the thermal aging resistance of the nanocomposites. For the SBR/CB/rectorite nanocomposite, the addition of CB helped to improve the interfacial compatibility between the filler and matrix, resulting in the best crack resistance as the aged SBR/CB/rectorite nanocomposite always demonstrated the least cracks on the surface during either stretching or bending experiments.