A new high frequency dynamic mechanical analysis system: An approach to direct high frequency testing of tire tread rubber

Dynamic Mechanical Analysis (DMA) systems are measurement devices for obtaining master curves and complex modules of viscoelastic materials, such as rubbers. The conventional DMAs measurement systems in market have several limitations, which restrict their ability for operating at high frequencies. Thus, Williams, Landel and Ferry (WLF) relation is used to produce master curves and predict the material properties at high frequencies. In conventional DMAs, experiments are done in a range of temperatures, and then a master curve is made for a chosen reference temperature by shifting the measurements data to high frequencies. Therefore, the obtained results, which are not based on direct measurements, can be inaccurate. In order to overcome this problem a new simple shear high-frequency DMA (HFDMA) system is designed and built to directly measure the dynamic mechanical properties of viscoelastic material at high frequencies and the strain levels sufficient for tire manufacturers. The new HFDMA can be used to test any viscoelastic materials which have glass transmission temperature (Tg) lower than room temperature (about 23 °C) such as the Styrene-butadiene rubber (SBR). The SBR is the base material for tire tread. The designing process of this new HFDMA is presented in this paper. The rubber specimen shape is chosen by taking into account the shear elastic wave effect, bending, buckling effect and heat generation in the specimen. The repeatability test is accomplished to ensure that the results obtained from the new HFDMA are repeatable and the repeatability uncertainty is about 0.04%. The new HFDMA is validated by comparing to the direct test results of conventional DMA at 100 Hz. The direct high frequency (5 kHz) complex shear modulus and damping factor are compared with the master curve of the conventional DMA developed by the use of WLF relation for SBR. This comparison revealed that the complex shear modulus and damping factor of the SBR obtained from the HFDMA at 5 kHz and 0.05% strain amplitude are about 7% and 6.5% higher than those obtained from the conventional DMA, respectively.     

The sulfur reversion process in natural rubber in terms of crosslink density and crosslink density distribution

Unfilled natural rubber compounds composed of conventional (CV), semi-efficient (SEV), efficient (EV) and sulfur donor (SD) vulcanization systems were heat aged to promote sulfur reversion. Rheometry, hardness, strain-strain characteristics including Mooney-Rivlin analysis, equilibrium solvent swell and Double Quantum (DQ) Nuclear Magnetic Resonance (NMR) were used to monitor crosslink density changes. A loss of crosslink density was observed by rheometry, C₁, equilibrium swelling and by DQ NMR as a function of cure extent. No chain scission reactions were operating in the time/temperature conditions used. All crosslink distributions were unimodal and the network homogeneity followed the order of EV > SD > SEV > CV. The crosslink distribution narrowed during the curing process for the CV and SEV systems. Non-oxidative maturation reactions were advantageous in promoting a more random distribution of crosslinks in the polymer matrix.     

Development of an O-ring from NR/EPDM filled silica/CB hybrid filler for use in a solid oxide fuel cell testing system

This research presents the effects of oxygen pressure and ambient temperatures on the crack behavior of O-rings from a semi-EV of NR/EPDM rubber with silica/CB filler, exposed to the inlet flow and outflow oxygen pressure in a Solid Oxide Fuel Cell (SOFC) environment. Blends of NR/EPDM were prepared with various ratios of silica/CB filler at 00/60, 10/50, 20/40, 30/30, 40/20, 50/10, and 60/00 phr. The fabricated O-ring complied with the standard for O-rings (TIS 2728-2559), with a minimum hardness of 65–75 Shore A, minimum tensile strength of 9 MPa, minimum elongation at break of 200%, and a minimum 100% modulus of 2.7 MPa. The mechanical properties of the compounds were tested, and the appropriate compound was chosen to make the O-rings to test in SOFC. The crack morphology of the fabricated O-rings was investigated and compared with a commercial O-ring after testing in the SOFC. As a result, the compound with silica/CB of 40:20 ratio provided the optimum mechanical properties, and passed the criteria standard of TIS 2728-2559. The mechanical properties of the prepared and commercial O-rings were similar (P-value of commercial with 60/00 = 0.273, 50/10 = 0.273, 40/20 = 0.144, 30/30 = 0.465, 20/40 = 0.465, 10/50 = 1.000 and 00/60 = 0.273; all > 0.05) and and both could still be continued to be used in SOFC despite some inner cracks after 24 h. The price of the prepared O-ring is cheaper than the commercial O-rings due to the low price of NR used in its formulation. Therefore, a prepared O-ring can be used in a SOFC, or other applications due to their mechanical properties and their reasonable price.     

Fabrication of exfoliated graphite reinforced silicone rubber composites - Mechanical,tribological and dielectric properties

The effect of exfoliated graphite (EG) on the mechanical, tribological and dielectric properties of the silicone rubber (QM) composites has been systematically investigated and analysed. Morphological analysis of the composites helps to understand the interfacial interaction between the filler and the rubber matrix as well as wear mechanism respectively. An enhancement in the mechanical, tribological and dielectric properties was observed with an increase in filler loading and better performance was observed at 7 phr of filler loading. The improvement in performance is attributed to the better interaction between the QM chains and the EG layers as evident from the AFM and TEM analysis. It is also evident from the Kraus plot which supports the reinforcing effect of EG in QM matrix.     

聚氯乙烯表皮成分对加成型硅橡胶固化的影响

采用流变学方法研究了双组分加成型硅橡胶在不同聚氯乙烯(PVC)表皮上的固化动力学,并利用红外光谱、核磁共振波谱、电感耦合等离子体质谱仪等手段分析了PVC表皮成分,以确定导致双组分加成型硅橡胶不固化的具体原因。 结果表明,PVC表皮中导致硅橡胶不固化的主要元素为P元素。 在固定硅橡胶厚度为1 mm的情况下,当PVC表皮中的P元素质量分数低于3×10^-3%时,浇注在其上的双组分加成型硅橡胶依然能固化;而当PVC表皮中的P元素质量分数超过约2.4×10^-2%时,虽然浇注在其上的双组分加成型硅橡胶的中间层依然能固化,但与PVC表皮接触部分的硅橡胶不固化,且不固化层厚度随P元素质量分数增加而增加。 本文还研究了在P元素质量分数低于3×10^-3%的PVC表皮上,降低硅橡胶厚度至微米级时的固化行为,在P元素质量分数低于3×10^-3%的PVC表皮上,当硅橡胶厚度低于2 μm时,硅橡胶出现不完全固化现象。 双组分加成型硅橡胶在含有P元素的PVC表皮表面的固化行为主要是由硅橡胶样品中铂催化剂总含量及PVC表皮中的P元素含量确定的,同时也会受到双组分加成型硅橡胶反应速率以及铂催化剂、P元素在硅橡胶中的扩散速率的影响。     

Flame retardancy and smoke suppression of silicone foams with microcapsulated aluminum hypophosphite and zinc borate

The flame‐retardant microcapsules were successfully fabricated with an aluminum hypophosphite (AHP) core. Fourier transform infrared (FTIR) and X‐ray photoelectron spectroscopy (XPS) were used to verify that AHP was encapsulated in the microcapsules, and thermogravimetry analysis showed that microencapsulated AHP (MAHP) possessed higher thermal stability than that of AHP. Then, a flame‐retardant and smoke suppression system for silicone foams (SiFs) was obtained through a synergistic effect of MAHP and zinc borate (2ZnO·3B₂O₃·3.5H₂O). The mechanical properties, flame retardance, and smoke suppression of SiFs with MAHP and zinc borate were tested using the tensile test, limiting oxygen index (LOI) test, UL‐94 test, and cone calorimeter test. The mechanical properties indicated that the tensile strength and elongation at break of SiFs could evidently improve with the incorporation of MAHP. Compared with pure SiF, SiF8 with 4.5‐wt% MAHP and 1.5‐wt% zinc borate could achieve an LOI value of 30.7 vol% and an UL‐94 V‐0 rating, the time to ignition amplified almost six times, the peak heat release rate and total heat release were 51.10% and 46.00% less than that of pure SiF, respectively, the fire performance index increased nearly 13 times, and the fire growth index value was only 13.18% of pure SiF. Moreover, the partial substitution of zinc borate imparted a substantial improvement in both flame retardancy and smoke suppression. Especially, the peak smoke production rate and total smoke production of SiF8 were merely 38.46% and 38.84% of pure SiF.     

Effects of the type of crosslink on viscoelastic properties of natural rubber

The viscoelastic properties of various crosslinked natural rubbers, NR, were investigated by mechanical spectroscopy. The glass transition temperature, T_g, was found to be dependent on both the crosslink density and the crosslink type. Higher values of T_g were obtained for sulfur-crosslinked NR than for peroxide-crosslinked NR at the same crosslink density. The greater influence of the sulfur content on T_g may be attributed to polysulfidic crosslinks and cyclic sulfide structures favored at high sulfur contents. Sulfur-vulcanized NRs with monosulfidic crosslinks, favored at relatively high accelerator/sulfur ratios, have properties more similar to the peroxide-cured NR with simple carbon(SINGLE BOND)carbon crosslinks covalent bonds, resulting in only small shifts in T_g. A qualitative analysis of monosulfidic crosslinks and polysulfidic structures was performed with ¹³C solid-state NMR spectroscopy. The storage modulus, E′, in the rubbery plateau region increased with increasing crosslink density. However, the crosslink type did not influence the moduli values as much as it influenced the T_g values. Different methods of detecting the crosslink density were also discussed. © 1996 John Wiley & Sons, Inc.     

Preparation and characterization of a homobifunctional silicone rubber membrane grafted with acrylic acid via plasma-induced graft copolymerization

Polyacrylic acid (PAA) was grafted onto the surface of silicone rubber membrane (SR) by plasma-induced graft copolymerization (PIP). Ar-plasma was used to activate the surface of SR. Also, a determination was made of the influences of plasma treatment power, pressure, time, grafted copolymerization reaction time, and monomer concentration on polymerization yield. The surface properties of SR were measured by ATR-FTIR, ESCA, and SIMS. In those analyses, the elemental composition and different carbon bindings on the surface of SR were examined by ESCA with the amount of O1s/C1s being approximately 0.7 at 60 s by Ar-plasma treatment (60 W, 200 mtorr). The peroxide group introduced on SR was measured via 1,1-diphenyl-2-picryhydrazyl (DPPH). The optimum amount of peroxide groups was 6.85 × 10⁻⁸ mol/cm² at 60 s of Ar-plasma treatment. The peroxide group (33D peak) was introduced onto the surface of SR by negative spectra of SIMS analysis after SR treatment by Ar-plasma. An increase was obtained in grafted polymerization yield with a region of 5 to 50% (v/v) of acrylic acid aqueous solution. Both sites of polyacrylic acid were detected after staining by toluidine blue O. That is, a homobifunctional membrane was developed via this surface modification method. © 1996 John Wiley & Sons, Inc.     

Structured latex particles as impact modifiers for poly(styrene–co-acrylonitrile) blends

This work was focused on the influence of the morphology of composite natural rubber (NR)-based particles on the toughness of poly(styrene–co-acrylonitrile) (PSAN) blends. In order to be suitable for the reinforcement of PSAN blends, the NR-based particles were coated with a shell of crosslinked poly(methylmethacrylate) (PMMA). Furthermore, polystyrene (PS) subinclusions were introduced into the NR rubber core. PSAN blends were prepared by adding the wet latex directly into a twin screw-extruder. This new method allowed even tacky pure rubber particles to be dispersed as shown by transmission electron photomicrographs which confirmed the integrity of the soft particles after mixing. Solid NR particles or NR-based latex particles containing rigid PS subinclusions and no hard shell did not offer any impact improvement to PSAN. Only NR-based core–shell particles containing at least 25% PMMA in the shell toughened the brittle matrix. Prevulcanized NR-based latex particles which do not cavitate easily were less effective. Core–shell particles containing PS subinclusions within a natural rubber core allowed more effective use of the rubber phase. From the fracture surface morphology the failure mechanisms of PSAN blends containing the different composite NR particles could be deduced. Monodisperse poly(n-butylacrylate)-based core–shell particles were too small to toughen PSAN. However, a similar dependence of the fracture mechanisms on the morphology of the incorporated toughening agent could be established by scanning electron microscopy.     

硫化丁苯橡胶纳观界面耐磨机理及参数影响分析

硫化橡胶因其良好的力学和物理化学性能而被广泛作为摩擦副的基础材料. 本文提出了一种硫化交联算法, 实现了C—C键的硫化互交联和自交联, 构建了硫化丁苯橡胶的分子动力学磨损模型, 从微观摩擦学的角度阐明了硫化交联结构对改善丁苯橡胶磨损性能的机理, 研究了不同界面参数对硫化橡胶微观磨损性能的影响. 结果发现 硫化使丁苯橡胶分子链的界面黏附能力和活动能力更弱, 拉伸和解缠能力更低, 磨损过程中界面累积能量更低, 更不容易脱离橡胶基体, 因此可以表现出更好的摩擦学性能, 更强的抗磨损性能; 随着速度的增大, 硫化橡胶的磨损率降低, 与宏观实验结果一致, 原因是硫化橡胶的原子分布函数和相互作用能随着速度增大而降低, 说明橡胶分子链的黏附能力和活动能力随着速度增加趋弱, 温升更低, 导致较低的磨损率; 压入深度对磨损率的影响规律则呈现相反的结果和趋势.