高效液相色谱氮杂冠醚键合固定相的合成及性能研究

我们曾用γ－氯丙基键合硅胶（ＣＰＳ），在氢化钠（ＮａＨ）作用下合成了３－（氮杂－１８－冠－６）丙基键合固定相（ＢＣＰ）［１］．该固定相对碱基、核苷酸、硝基苯酚等有较好的分离选择性，但由于ＮａＨ对硅胶基质腐蚀作用较大，导致ＢＣＰ柱效及渗透性较低．本文采...     

CuCrAl和CuCrZr低温液相合成甲醇催化剂的研究

 用络合共沉淀法制备了CuCrAl和CuCrZr复合氧化物液相合成甲醇催化剂，其比表面分别达到119和116m2／g．在5．0～5．5MPa和383K条件下，分别用间歇式和流动式反应釜考察了催化剂的活性和稳定性．结果表明：CuCrAl和CuCrZr的活性均明显高于CuCr；CuCrAl的活性略高于CuCrZr，但甲酸甲酯（MF）的选择性明显低于CuCrZr；两者在12h内未见活性明显下降．甲醇钠在反应过程中部分转化为甲酸钠和NaOH．CuCrAl和CuCrZr有较高的氢解活性可抑制甲醇钠与MF生成甲酸钠，从而有较低的甲酸钠浓度．但是，Al2O3和ZrO2的酸性有利于甲醇脱水，引起甲醇钠水解生成NaOH．溶剂对CuCr基催化剂的活性和选择性有明显影响．对反应机理进行了讨论．     

Axial dispersion in a liquid fluidized bed of particles akin to immobilized enzymes

The axial dispersion of a liquid fluidized bed of controlled pore silica (CPS) particles has been determined by the pulse tracer method. The CPS used was the same as for enzyme immobilization, having an average diameter of 0.436 mm and mean pore size of 37.5 nm. The fluidization liquid is α-amylase liquefied manioc starch, 30% w/v, 45°C pH=4.5. Nominal bed porosities tested were 0.7 and 0.8. The results show that the axial dispersion coefficient increases with greater superficial liquid velocities. Various available correlations tested disagree with each other to a large extent and are unable to represent collected experimental data.     

Effect of Hydration–Dehydration Processes on the Structure and Porosity of Detemplated Silica Fibers

A study was carried out on the conditions of template removal (calcination or extraction by solvents) and hydration–dehydration processes on the hexagonal structure and porosity of detemplated fibers. The hydration–dehydration cycle leads to a decrease in fiber porosity, especially in fiber detemplation by extraction with surfactant solvents such as ethanol and acetic acid.     

8-羟基喹啉-硅胶介质的合成及其在海水中痕量铅检测的应用

详细研究了以大孔硅胶为基质,一步合成8羟-基喹啉(8-HQ)型金属螯合色谱填料的方法,采用正交试验对合成方法进行了优化。与传统合成方法所得的填料进行了比较,从理化指标等方面来看,新的合成方法为佳。将该法用作微柱流动注射(FIA)在线分离、富集和电感耦合等离子体质谱(ICP-MS)分析流程中的固定相,对大洋海水中的痕量铅进行了在线分析,得到了较满意的结果。     

沉淀二氧化硅消光剂的制备研究

涂料中的消光剂是一类能够改变涂膜表面光学性能的助剂。这类助剂能够在涂膜表面产生预期微粗糙度,使涂膜的光泽显著降低,给人一种古朴典雅的感觉。近几年来,我国的涂料工业方兴未艾,涂料总产量也跃居世界的前列。在这期间高光泽的亮光涂料以其色泽鲜艳、明亮等优点深受消费者的喜爱,并在相当长的时间内一统着涂料市场[1]。但是,随着人们生活水平的不断提高,一方面消费者感觉到了高光泽的亮光涂料成膜后反光比较严重,对人的眼睛有害;另一方面消费者的审美观念越来越倾向于休闲、时尚和个性化。这些因素就导致了人们对具有柔和外观的低光泽涂…     

An application of factorial design to the development of fused silica capillary columns

Stationary phase crosslinking conditions for fused silica capillary columns were optimized with the use of a factorial design experiment. This experimental strategy was chosen because it provided for the determination of two-factor interactions. A predictive model was developed for the desired chromatographic performance parameters as a function of the variables of the crosslinking reaction. Confirmatory experiments proved the usefulness of the mathematical model which resulted in the production of capillary columns of superior performance with significant improvements in reproducibility.     

Solid-phase extraction of iron(III) with an ion-imprinted functionalized silica gel sorbent prepared by a surface imprinting technique

A new Fe(III)-imprinted amino-functionalized silica gel sorbent was prepared by a surface imprinting technique for selective solid-phase extraction (SPE) of Fe(III) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Compared with non-imprinted polymer particles, the ion-imprinted polymers (IIPs) had higher selectivity and adsorption capacity for Fe(III). The maximum static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Fe(III) was 25.21 and 5.10 mg g⁻¹, respectively. The largest selectivity coefficient of the Fe(III)-imprinted sorbent for Fe(III) in the presence of Cr(III) was over 450. The relatively selective factor (α_r) values of Fe(III)/Cr(III) were 49.9 and 42.4, which were greater than 1. The distribution ratio (D) values of Fe(III)-imprinted polymers for Fe(III) were greatly larger than that for Cr(III). The detection limit (3σ) was 0.34 μg L⁻¹. The relative standard deviation of the method was 1.50% for eight replicate determinations. The method was validated by analyzing two certified reference materials (GBW 08301 and GBW 08303), the results obtained is in good agreement with standard values. The developed method was also successfully applied to the determination of trace iron in plants and water samples with satisfactory results.     

Synthesis of siloxane stationary phases for capillary gas chromatography and supercritical fluid chromatography

A comparison is made between dichlorosilanes and cyclic siloxanes as starting materials in the synthesis of stationary phases for capillary gas chromatography (CGC) and supercritical fluid chromatography (SFC). Siloxanes containing one or more of the side groups methyl, vinyl, phenyl, and cyanoethyl in various ratios were synthesized and compared. These phases were characterized by chromatographic (gel permeation, GPC), spectroscopic (IR, ¹H NMR, ²⁹Si NMR), and thermal (DSC) methods. Coated fused silica columns were evaluated with respect to polarity, crosslinkability with several free-radical initiators, and thermal stability. A new liquid phase, 7% cyanoethyl, 7% phenyl, 1% vinyl methyl polysiloxane is shown to be more polar than OV-1701, more temperature stable, easily crosslinked and suitable for use in supercritical fluid chromatography.     

Glass capillary columns for separation of free organic acids

Glass capillary columns have been prepared without acidic additive in the stationary phase, from which free organic acids elute as sharp and symmetrical peaks. The required surface in the borosilicate glass capillary was generated by a combination of leaching with aqueous HCl and deposition of colloidal silica particles; it can be coated with stationary phases have a broad range of polarity. Aqueous samples containing free organic acids can also be analyzed in such columns in an isothermal mode.