混合集成电路激光功能调值技术

本文提出了激光功能微调技术在高精度混合集成电路上的应用，讨论了关键技术问题，并以实例具体说明。该技术的应用为研制高精度混合集成电路开辟了新途径。     

STN—LCD的新进展

STN-LCD采用新的取向层,消除了残象;采用新的驱动波形,消除了串扰;采用二(口恶)烷、卤化物、链烯基、醚和二苯乙炔,改进了液晶料材的性能,使STN-LCD获得高的对比度、快的响应速度、低的驱动电压;采用有源矩阵驱动方法,消除了帧响应,使STN-LCD获得高的对比度、高的亮度及视频响应速度;使用温度跟踪电路,自动跟踪STN-LCD的阀值电压,使STN-LCD获得宽的工作温度。     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

用于多种组装技术的厚膜导体复合结构

厚膜导体Ｐｄ－Ａｇ／Ａｕ、Ｐｔ－Ｐｄ－Ａｕ／Ａｕ平面复合结构，Ｐｄ－Ａｇ／Ａｕ立体复合结构可使多种组装技术相互兼容。立体复合结构还可有效地降低导体线电阻，减少线损耗。而且，其超声键合性尤佳     

Memory management optimization problems for integrated circuit simulators

In hardware design, it is necessary to simulate the anticipated behavior of the integrated circuit before it is actually cast in silicon. As simulation procedures are long due to the great number of tests to be performed, optimization of the simulation code is of prime importance. This paper describes two mathematical models for the minimization of the memory access times for a cycle-based simulator.An integrated circuit being viewed as a directed acyclic graph, the problem consists in building a graph order on the vertices, compatible with the relation order induced by the graph, in order to minimize a cost function that represents the memory access time. For both proposed cost functions, we show that the corresponding problems are NP-complete. However, we show that the special cases where the graphs are in-trees or out-trees can be solved in polynomial time.     

MOS功率驱动高速脉冲激光器的研究

运用经典电路理论,对MOS功率管的开关特性、驱动原理进行了分析,导出了应用MOS功率管实现高速大电流开关应遵从的原则和方法,并成功地实现了光脉冲上升时间小于5ns、下降时间小于10ns,驱动电流达10～50AP-P激光器电源的要求.     

基于单片机控制的实验线路故障诊断系统

介绍了基于单片机控制技术的强电实验线路故障自动诊断系统的结构及功能,阐述了系统硬件设计、软件设计的基本原理．     

基于改善空间关联性的混沌控制

基于混沌信号的统计特性，提出了一种通过改善混沌信号的空间关联性实现混沌控制的方法.以Hénon离散混沌系统和四阶Chua's电路超混沌连续系统为例进行了数值研究，验证了这种控制方法的有效性.结果表明， 通过改善混沌信号之间的空间关联性， 混沌系统能以较快的速度收敛到它的平衡点或多种周期轨道. 关键词： 混沌控制 空间关联性 Hénon系统 四阶Chua's电路     

光束偏转法自动测试激光等离子体冲击波系统的研制

根据光束偏转原理，研制了激光等离子体冲击波自动测试系统的硬件和软件。该系统使用计算机与可编程序控制器作为上下位机，采取上下位机通讯的方式控制步进电机及二维移动架的移动，以改变探测光的相对位置，并利用单模光纤和光电倍增管将探测到的光偏转信号传入数字示波器进行存储，最后计算机将示波器中采集到的光偏转信号进行分析处理。使用该系统对激光等离子冲击波的衰减过程进行了实际测试，得到了较为理想的实验结果。     

用图像分析限流和分压接法中滑动变阻器的选取

借助Ux-Rap图像分析得出滑动变阻器的选取原则:控制电路采用限流接法时,要求滑动变阻器的最大阻值与被测电阻的阻值接近,即接近为原则;控制电路采用分压式接法时,滑动变阻器的最大阻值应远小于被测电阻的阻值,故在分压接法中,应选择阻值较小而额定电流较大的滑动变阻器.