Local adsorption sites and bondlength changes in Ni(1 0 0)/H/CO and Ni(1 0 0)/CO

The local adsorption geometry of CO adsorbed in different states on Ni(1 0 0) and on Ni(1 0 0) precovered with atomic hydrogen has been determined by C 1s (and O 1s) scanned-energy mode photoelectron diffraction, using the photoelectron binding energy changes to characterise the different states. The results confirm previous spectroscopic assignments of local atop and bridge sites both with and without coadsorbed hydrogen. The measured Ni–C bondlengths for the Ni(1 0 0)/CO states show an increase of 0.16 ± 0.04 Å in going from atop to bridge sites, while comparison with similar results for Ni(1 1 1)/CO for threefold coordinated adsorption sites show a further lengthening of the bond by 0.05 ± 0.04 Å. These changes in the Ni–CO chemisorption bondlength with bond order (for approximately constant adsorption energy) are consistent with the standard Pauling rules. However, comparison of CO adsorbed in the atop geometry with and without coadsorbed hydrogen shows that the coadsorption increases the Ni–C bondlength by only 0.06 ± 0.04 Å, despite the decrease in adsorption energy of a factor of 2 or more. This result is also reproduced by density functional theory slab calculations. The results of both the experiments and the density functional theory calculations show that CO adsorption onto the Ni(1 0 0)/H surface is accompanied by significant structural modification; the low desorption energy may then be attributed to the energy cost of this restructuring rather than weak local bonding.     

SD2300在新型TMS320F28x DSP实时监测系统中的应用

SD2300是兴威帆电子公司生产的一种新型高精度实时时钟芯片。TMS320F2812是TI公司最新推出的DSP芯片，该芯片广泛地运用于测控和控制场合。文中给出了基于SD2300和TMS320F2812的时钟输入、低功耗“软件时间锁”的硬件和软件设计方法。     

模糊全区间序结构

本文试图对模糊偏好结构及模糊全区间序结构的定义进行探讨，并讨论它们的性质．以Fodor等提出的公理为基础，给出了模糊偏好结构的定义，同时对一类重要的模糊偏好结构-模糊全区间序结构的性质进行了讨论，得出了模糊全区间序结构的一些充要条件．     

Filter-radiometer-based realization of candela and establishment of photometric scale at UME

The luminous intensity unit of candela was realized based on filter-radiometer, which is traceable to detector-based primary standard electrical substitution cryogenic radiometer (ESCR). In that realization the traditional Osram Wi41/G-type incandescent lamp and filter-radiometer consisting of an aperture, a V(λ) filter and a silicon photodiode based trap detector were used as light source and detection element, respectively. Measurement techniques of effective aperture area, spectral transmittance of V(λ) filter and absolute responsivity of trap detector are also presented.     

Evolution of grain structure in thin film reactions

In this paper, we examine, both experimentally and theoretically, the kinetics of formation and microstructure of product phases in thin film reactions, using the Nb/Al and Ti/Al systems as our prototypes. The results of calorimetry and microscopy studies are interpreted using simple kinetic and morphology models. In particular, the kinetic models employed here focus on the nucleation and growth components of the phase formation process and the morphology models provide a starting point for the classification of product grain structures. An erratum to this article is available at .     

Investigation and optimization of the covering power and coloristic properties of paint coatings of complex composition

A method for finding the optimum sizes of pigment particles, their volume concentration, and the paint coating thickness that provide the covering power and the required coloristic characteristics of reflected light for the minimum flow rate of pigments is based on using a four-flow approximation of the solution to the equation of radiation transfer in dispersion media and is extended to coatings of complex composition. The capabilities of the method are demonstrated by examples of coatings of mixtures of hematite and rutile particles in a binder with n=1.5 for variations of the modal size and the half-width of the size distribution of the pigment particles. B. I. Stepanov Institute of Physics, Academy of Sciences of Belarus, 70, F. Skorina Ave., Minsk, 220072, Belarus. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 90–96, January–February, 1997.     

电站锅炉系统性能仿真模型的建立

1引言根据热力学第二定律，燃料中的化学拥将近一半损失在锅炉的燃烧与传热过程中。因此，优化锅炉性能对降低整个火电机组的煤耗率具有明显效果。完整的锅炉系统由磨煤机、送风机、一次风机、弓讯机、炉膛、汽包、过热器、再热器、省煤器、空气预热器等单元组成，这些单元之间的联结错综复杂。本文建立了锅炉系统中通用单元的性能模型，并在此基础上，对锅炉系统的结构特点进行了分析，利用过程系统工程中的序贯模块法建立了整个锅炉系统的性能模型。对单元的划分、回路的切断及断裂流股的收敛与迭代策略提出了自己的观点。最后根据生产厂…     

智能工作站主机的MMPIS实验模型研究──一个全互连式结构MMPIS硬件环境的设计与实现

本文介绍中日国际合作开发研究的Ａ１型智能网（Ａ１型ＩＮ）智能工作站（ＩＷ）主机的并行推理硬件结构的实验模型设计与实现，给出了一种并行推理硬件支持环境实现方案和该方案在实现中若干问题的解决方法。     

微波宽频带功率负载的研究

介绍了５００Ｗ宽频带功率负载的设计及实验结果，并将研究成果扩展到１０～１０００Ｗ范围。负载主要技术指标：输入阻抗５０Ω，频带宽度０～１０００ＭＨｚ，电压驻波比≤１．１．表面最高温升△ｔ≤１００℃。     

噪声测量作为筛选光电耦合器件的一种方法

本文针对目前用于光电耦合器件筛选方法的不足，提出了用测量耦合器件噪声功率谱的方法来筛选掉噪声值大的器件，给出一批光电耦合器件的测量统计结果及在不同工作点时的噪声功率谱，并给出相应的筛选标准，实验结果表明，这种方法是有效、可行的。