Emulsion polymerization of methyl methacrylate under pulsed microwave irradiation

Emulsion polymerization of methyl methacrylate (MMA) under pulsed microwave irradiation (PMI) with higher peak pulse power was studied. The effects of various parameters of PMI on the polymerization were analyzed and compared with that under conventional heating (CH) process. The results were summarized, as compared with that under CH, as follows. The amount of initiator used to reach constant conversion reduced by 50% at the same polymerization time; at the same initiator concentration 0.15 and 0.2 wt.%, the polymerization rate increased by 131% and 163%, respectively. The molecular weight of polymer obtained was 1.1-2.0 times larger than that under CH; at the same irradiation energy, the conversion achieved using a lower pulse power was greater than that using a higher pulse power. There seemed to be a factor of the irradiation energy efficiency; in other words, for the monomer conversion, the irradiation energy of low pulse power had a higher efficiency. The conversion achieved using a 3.5 μs pulse width was almost the same as that using a 1.5 μs pulse width. The results indicated that PMI had a significant non-thermal effect on the emulsion polymerization of MMA so as to effectively enhance the polymerization rate. The glass transition temperature (T_g), the polydispersity index (PDI) and the regularity of the polymer obtained using two processes were similar, indicating that the physical properties and microstructure of the polymer were not modified by the use of microwaves.     

Effect of initiators on grafting in the initial stage of the emulsion polymerization of methyl methacrylate using poly(vinyl alcohol) as a protective colloid

 To make clear the reason of unsuitability of poly(vinyl alcohol) (PVA) protective colloid for the emulsion polymerization of conjugated monomers, a model experiment of emulsion polymerization of methyl methacrylate (MMA) was carried out with ammonium persulfate (APS) or azobis(isobutyronitrile) (AIBN) initiators, where a small amount of MMA (1/100th of the concentration compared with ordinary emulsion polymerization) was employed. This corresponds to the initial stage of the emulsion polymerization. Grafting of MMA onto PVA took place remarkably irrespective of the kind of the initiators. Formation of homo-poly(MMA) was observed to a small extent. The formation of new emulsion particles smaller than 100 nm continued to increase to almost the end of the polymerization. PVA molecules in the grafted polymer are supposed to act as stabilizers of newly formed particles. From kinetic treatment using the experimental data, the important issues were derived as follows. Firstly, the sulfate anion radical from APS is much more reactive than the isobutyronitrile radical from AIBN in terms of hydrogen abstraction from PVA. Secondly, high grafting ability of the latter initiator system, notwithstanding the much lower reactivity in the hydrogen abstraction compared with the APS system, is attributed to the relative reactivity of the primary radicals, i.e., hydrogen abstraction reaction from PVA to initiation reaction with MMA. The much slower rate of addition of the isobutyronitrile radical to the monomer compared with that of hydrogen abstraction from PVA facilitates the grafting, although the rate constant of hydrogen abstraction is far smaller than that with the sulfate anion radical by 10⁻⁴ times. Received: 26 April 2001 Accepted: 6 September 2001     

Redox Polymerization of Methyl Methacrylate in the Fluorous Triphasic System

Fluorous-phase chemistry is currently a topic of considerable interest1-6. Since fluoroustriphasic reactions were first described by the Curran and co-workers7, this triphasicsystem has been widely used for detagging7,8 and phase-vanishing reactions9-11. …     

Investigation of the detection limit for the determination,by pyrolysis-capillary GC,of the thickness of ultra thin PMMA layers coated on to PET film

The determination of nanometer thick layers of poly(methyl methacrylate) coated on to the surface of poly(ethylene terephthalate) film has been investigated by high resolution pyrolysis gas chromatography without sample pretreatment or modification of the instrumentation used. A good linear relationship was observed between the quantity of the characteristic pyrolysate and the thickness of the poly(methyl methacrylate) layer; the detection limit was sufficient to enable the quantitation of poly(methyl methacrylate)-to-poly(ethylene terephthalate) film thickness ratios of 1:20000 in composite materials.     

甲基丙烯酸三苯墓甲酯和甲基丙烯酸酯类的共聚物在溶液中的螺旋诱导和解旋作用

甲基丙烯酸三苯墓甲酯和甲基丙烯酸酯类的共聚物在溶液中的螺旋诱导和解旋作用陈传福，刘卫宏，陈永明，任长玉，习复（中国科学院化学研究所北京１０００８０）关键词甲基丙烯酸三苯基甲酯，甲基丙烯酸甲酯，光学活性，螺旋诱导，解旋在手性阴离子复合引发剂存在下，甲基...     

STRUCTURE AND PROPERTIES OF P(MMA-MAA)/PEO INTERMACROMOLECULAR COMPLEX FORMED THROUGH HYDROGEN BONDING

The superstructure and properties of polymers might be improved and enhanced througl intermolecular complexation. In this paper, the preparation, structure and properties of P(MMA-MAA)/PEO intermolecular complex through hydrogen bonding are studied. By acid hydrolysis of PMMA, a series of P(MMA-MAA) copolymers have been prepared, the MAA content of which depends on the temperature and time of hydrolyzation. In case the MAA content in P(MMA-MAA) is beyond 0.4 mole fraction, the hydrogen bonding between P(MMA-MAA) and PEO is strong enough to form intermolecular complex. The supermolecular structure of the complex is quite different from that of its constituent, which was observed by an X-ray diffraction and transmission electron microscope. The crystallization of PEO is confined owing to complexation. The complex exhibits quite a lot of good properties in thermal stability, gas permeability as well as mechanical strength, and could be used in many fields.     

聚氨酯／聚甲基丙烯酸甲酯互穿聚合物网络的研究

本文对(蓖麻油-聚乙二醇)聚氨酯/聚甲基丙烯酸甲酯(PU/PMMA)互穿聚合物网络(IPN)体系进行了研究.实验结果表明:IPN的力学性能受网络化学构型控制.在PU/PMMA为25/75时,应力-应变曲线出现屈服点,产生类似皮革行为,并在此点抗张强度最高,表现明显的协同效应.动态力学性能及电镜均证明该体系相分离十分严重,通过加入扩链剂及网间交联剂能显著改善两组分相容性,其中网间交联剂效果最好。     

Study of the influence of physical aging on macroradical decay in poly(methyl methacrylate)

The macroradical decay in poly(methyl methacrylate) samples with different thermal histories was investigated in the temperature interval 20–100 °C using ESR spectroscopy and the second order kinetic model. The rate constants exhibit two different regimes with the transitions atT _tr=68±1°C which are independent of thermal treatment. ForT<T _tr andT>T _tr the rate constants as well as the corresponding activation parameters are sensitive to history because of different physical microstructures. The compensation law, i.e., the linear relation between lnk _{o, eff} andE _eff, was analyzed in terms of the so-called compensation quantitiesk _c andT _c and a proximity betweenT _c=T _tr andT _o=53±3 °C — Vogel temperature for -segmental dynamics was found. A comparison of kinetic and dynamic data suggests that the decay of terminal macroradicals in the low-temperature region is controlled by secondary relaxations and that the -mobility contributes to a more rapid decay at higher temperatures belowT _g.     

Thermogravimetric analysis of poly(alkyl methacrylates) and poly(methylmethacrylate-g-dimethyl siloxane) graft copolymers

The thermal stabilities of various poly(alkyl methacrylate) homopolymers and poly(methyl methacrylate-g-dimethyl siloxane) (PMMA-g-PSX) graft copolymers have been determined by thermogravimetric analysis (TGA). As expected, the thermal stabilities of poly(alkyl methacrylates) were a function of the ester alkyl group, and polymerization mechanism. In particular, thermally labile linkages, which result from termination during free radical or nonliving polymerization mechanisms, decrease the ultimate thermal stabilities of the polymers. However, graft copolymers, which were prepared by the macromonomer technique with free radical initiators, exhibited enhanced thermal stability compared to homopolymer controls. A more complex free radical polymerization mechanism for the macromonomer modified polymerization may account for this result. © 1994 John Wiley & Sons, Inc.     

Radiation-induced polymerization of methyl methacrylate in microemulsion with high monomer content

γ-Ray-induced polymerization of methyl methacrylate was conducted in a microemulsion stabilized by a mixture of sodium of 12-acryloxy-9-octadecenoic acid (AOA) and sodium dodecyl sulfate (SDS) with various weight ratios at room temperature. The experimental data showed that the mixture of AOA and SDS with a weight ratio 2 was an efficient surfactant system for the microemulsion containing 38.6 wt% MMA and 5.5 wt% surfactant. The effects of MMA concentration and dose rate on the polymerization kinetics and particle size are discussed.