数值孔径与数字剪切散斑干涉条纹亮度的关系

分析了数字剪切散斑干涉条纹图的形成理论，并获得了条纹亮度与摄象机数值孔径等参数的精确关系式，从理论分析和实验验证均得出在采用小的摄象机数值孔径和３ｍＷ Ｈｅ－Ｎｅ激光器的情况下，仍可获得比较满意的数字剪切散斑干涉条纹图，理论工作及其结论对于进行数字剪切散斑干涉实验的最佳参数选择具有指导作用。     

天线方向图的复射线仿真

根据复射线理论，利用复源点高斯波束场来模拟天线的远场方向图。本文提出三种模拟方法，即主瓣匹配法，峰值匹配法和逐点匹配法，给出了多种方向图的仿真结果。数值分析和优化结果表明，复射线峰值匹配法是一种精确实用的天线方向图仿真技术。     

计算抛物面天线支杆对方向图影响的简化方法

本文基于物理光学球面波展开法，提出一种计算抛物面天线支杆对其方向图影响的简化方法，文中导出了计入支杆散射的天线辐射方向图的解析表达式，并给出了支杆对其方向图旁瓣电平影响的计算实例，数值结果表明，本文所提出的新方法不仅计算结果精度高，而且所需计算机容量小，运算速度快，可应用于天线工程设计。     

叠栅图在碳化物沉淀相研究中的一些应用

借助于叠栅图观察了合金钢中细小沉淀相的形貌和分布特征，确定了沉淀相的点阵常数及其同母相（或另一沉淀相）的错配度，并确认了沉淀相或母相中存在的位错及其滑移面。     

全双极WTA模型的改进及其实现

提出了一种相似度的新定义，使双极ＷＡＴ模型的实现更加简洁明了。增加一个阈值使系统能判别非存储模式或因其信息量过低而无法鉴定的输入模式，阈值的大小与要求的容错能力有关。双极相似度及阈值通过光学方法实现。阈值的光学实现使系统仍具有照明不变性。通过电路实现取及ＷＴＡ网络的迭代运算。     

Calculation of heat transfer and uniformity of chemical amplification during post-exposure bake

Heat transfer in a resist-coated silicon wafer using a bake process is theoretically evaluated by modeling the three-dimensional diffusion process, focusing on the controllability of the lithographic performance of chemically amplified resists. Six models of various ambient conditions are used. The proximity gap between the hotplate and the wafer is found to have a dominant influence on the heat transfer process for the whole system. Because the atmosphere near the wafer acts as a thermal diffusion buffer layer, no temperature gradient occurs in the resist, even when it is subjected to convective heat transfer from the resist surface. Experimental results obtained by X-ray lithography confirm the calculation results.     

A 24-GHz Patch Array with a Power Amplifier/Low-Noise Amplifier MMIC

This paper presents an active patch array designed at 24 GHz. It can be used as a front-end component for a phased array. A series resonant array structure is chosen which is compact and easy excite. With 5 elements, the array proved a 12-dB antenna gain. A power amplifier and a low noise amplifier are designed on a single GaAs chip (PALNA). Bias switch is used in the PALNA, which greatly reduces the switch loss in a transceiver and increases the efficiency. 20-dB small signal gain is achieved in both power amplifier and low noise amplifier. The active patch array is built by the combination of the patch array and PALNA. The measured active gain of this antenna is 35-dB for the PA mode and 31-dB for the LNA mode. This active patch array can obtain an EIRP of 34 dBm with a total radiated power of 22dBm and a maximum PAE of 32%. To check the noise performance, we applied sources at both normal temperature and 77K (liquid nitrogen) and extracted the noise figure (3.5 dB) of the active antenna by the Y factor method. The results proved that the active antenna is working efficiently as both a transmitting and receiving antenna.     

Measurement selection for parametric IC fault diagnosis

This article presents experimental results which show feedforward neural networks are well-suited for analog IC fault diagnosis. Boundary band data (BBD) measurement selection is used to reduce the computational overhead of the FFN training phase. We compare the diagnostic accuracy between traditional statistical classifiers and feedforward neural networks trained with various measurement selection criteria. The feedforward networks consistently perform as well as or better than the other classifiers in term of accuracy. Training using BBD consistently reduces the FFN training efforts without degrading the performance. Experimental results suggest that feedforward networks provide a cost efficient method for IC fault diagnosis in a large scale production testing environment.This work is supported by NSF-IUC CDADIC, Project 90-1.     

基于DFT插值的宽带波束形成器设计

本文提出一种基于DFT插值的宽带波束形成器设计方法。首先推导了具有频率不变波束图的连续线阵的灵敏度函数与离散线列阵加权系数之间的关系；接着给出了基于DFT插值的宽带波束形成器设计的两个步骤：（1）使用窄带波束形成器的设计方法计算在参考频率下基阵的加权系数；（2）根据参考频率下基阵的权系数与其它子带权系数之间的关系，利用DFT插值的方法求出其它子带的加权系数。最后，给出了一个设计实例说明本文方法的有效性。     

用投影预变换提高自适应波束形成的稳健性

在快拍数较少和（或）存在系统误差时，自适应波束形成的性能会变差，特别是会引起方向图副瓣电平升高——波束畸变。本文提出的投影变换法利用干扰方向的初略估计，在未精确预知阵列流形的条件下，可以显著改善自适应方向图的副瓣性能，并提高自适应算法的收敛性，计算机仿真结果验证了这一优点。