玫瑰花状氢氧化钴的结构和浸润性

在没有任何表面活性剂条件下,通过简单的方法首次合成了玫瑰花状β-Co(OH)₂微晶。玫瑰花状β-Co(OH)₂微晶宽3~5μm,厚2~3μm,是由平均厚度为15nm的纳米片所组成。玫瑰花状β-Co(OH)₂组成的薄膜的接触角为158.5°±1.2°,表面处于任意的角度,水滴都不会滴落。     

Thermomechanical behavior of underfill/solder mask/substrate interface under thermal cycling

With the increasing application of flip-chip technology in the microelectronics industry, the adhesion strength of interfaces in flip-chip microelectronic structures has become an important issue for manufacturing and operation. In this paper we present an experimental investigation of the adhesive strength of underfill material to solder mask coated FR-4 substrate under thermal cycling. The effects of the number of thermal cycles on interfacial strength were investigated by using the button shear test. The relationship between interfacial strength and the thickness of solder mask was also examined. Furthermore, the morphologies of fracture surfaces of the test specimens were analyzed by scanning electron microscopy. The results of this study show that the interfacial strength of the underfill/solder mask/substrate joint was significantly reduced by thermal fatigue. Finally, the degradation behavior and possible mechanisms were then determined on the basis of these observations.     

MEASUREMENT OF ADHESION FORCES IN AIR WITH THE VIBRATION METHOD

The vibration method represents a practical method for the measurement of adhesion forces and adhesion force distributions. This method causes sinusoidally altemating stresses and yields detachment and contact forces between particles and substrate of the same order of magnitude. Alternating contact forces of the vibration method can cause an adhesion force intensification through flattening of asperities. The measuring principle of the vibration method and the analysis of experimental results are described in the article. Normal adhesion forces (pull-off forces) are measured using the vibration method and the colloidal probe technique. The results of both methods show good agreement for small particle sizes. The influence of the detachment force direction is shown by comparing tangential and normal adhesion forces measured using particle reentrainment in a turbulent air flow and the vibration method, respectively. The surface roughness of the substrate and the relative humidity are shown to significantly influence the measured adhesion forces. For the calculation of the adhesion forces, an approach by Rabinovich was combined with approximations of plastic micro asperity flattening. The Rabinovich approach accounts for roughness effects on the van der Waals force by incorporating the rms roughness of the interacting surfaces. rms-values of the particles and substrates were measured with atomic force microscopy at different scanning areas.     

微梁与基底间的毛细粘附作用

在表面微型机械结构的制造过程中,强的毛细相互作用常常使得组成这些结构的微桥、微梁与基底粘附而导致失效。而在微尺度实验中,微桥与微梁又是微尺度材料常数和性能检测的常用的试件样式,如果实验中加载端与被检测的微尺度试件发生毛细粘附,将直接影响检测数据的准确性。本文应用微悬臂梁试件,讨论微梁与基底间的毛细粘附作用,并通过能量原理计算其粘附力的大小和试件几何尺寸、粘附面距离、粘附液体特性之间的关系。最后应用微散斑干涉,检测粘附平衡态时微桥和微梁的粘附力以及由毛细粘附所导致的弯曲变形,并与理论计算结果进行比较。     

A parametric study of laser induced thin film spallation

We report parametric studies of elastic wave generation by a pulsed laser and associated spalling of thin surface films by the corresponding high stresses. Two different substrate materials, single crystal Si (100) and fused silica, are considered. Spallation behavior of Al thin films is investigated as a function of substrate thickness, film thickness, laser energy, and various parameters governing the source. Surface displacement due to the stress wave is measured by Michaelson interferometry and used to infer the stresses on the film interface. Consistent with previous studies, the maximum stress in the substrate and at the film/substrate interface increases with increasing laser fluence. For many of the conditions tested, the substrate stress is large enough to damage the Si. Moreover, the maximum interface stress is found to increase with increasing film thickness, but decrease with increasing substrate thickness due to geometric attenuation. Of particular significance is the development of a decompression shock in the fused sillica substrates, which results in very high tensile stresses at the interface. This shock enhances the failure of thin film interfaces, especially in thicker samples.     

Lactic acid bacteria in dairy food: Surface characterization and interactions with food matrix components

This review gives an overview of the importance of interactions occurring in dairy matrices between Lactic Acid Bacteria and milk components. Dairy products are important sources of biological active compounds of particular relevance to human health. These compounds include immunoglobulins, whey proteins and peptides, polar lipids, and lactic acid bacteria including probiotics. A better understanding of interactions between bioactive components and their delivery matrix may successfully improve their transport to their target site of action. Pioneering research on probiotic lactic acid bacteria has mainly focused on their host effects. However, very little is known about their interaction with dairy ingredients. Such knowledge could contribute to designing new and more efficient dairy food, and to better understand relationships between milk constituents. The purpose of this review is first to provide an overview of the current knowledge about the biomolecules produced on bacterial surface and the composition of the dairy matter. In order to understand how bacteria interact with dairy molecules, adhesion mechanisms are subsequently reviewed with a special focus on the environmental conditions affecting bacterial adhesion. Methods dedicated to investigate the bacterial surface and to decipher interactions between bacteria and abiotic dairy components are also detailed. Finally, relevant industrial implications of these interactions are presented and discussed.     

Adhesion of nonplanar wrinkled surfaces

Topological patterns on polymer surfaces can significantly alter and control adhesion. In this study, the effect of surface wrinkles on a spherical surface on adhesion has been studied. Surface wrinkling induced by swelling of a crosslinked polydimethylsiloxane elastomer constrained by a stiff, thin surface layer (silicate) is used to produce topographic features of various length scales over a large curved area. By controlling the properties of the stiff layer and the applied strain conditions, surface wrinkles of varying amplitude and wavelength are obtained. The effect of wrinkle morphology on adhesion is quantified, and the results display a transition from enhancement of adhesion to decrease depending upon wrinkle dimensions. A simple phenomenological model is proposed that describes the change of adhesion behavior as a function of wrinkle morphology. Our results provide a critical understanding toward tuning the adhesion behavior of nonplanar surfaces consisting of periodic topographic structures. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Construction and activity of a synthetic basement membrane with active laminin peptides and polysaccharides

Cell-adhesive peptides derived from extracellular matrix (ECM) proteins are potential candidates for incorporating cell-binding activities into materials for tissue engineering. We have identified a number of cell adhesive peptides from laminins, which are major components of basement membrane ECM. Our goal is the development of synthetic basement membranes using the peptides on scaffolds. We review peptide–polysaccharide complexes, which were prepared by conjugation of the peptides to chitosan and alginate, and the biological activities of the resulting matrices. The peptide–polysaccharide matrices can also be used as a biomaterial for cell transplantation. These studies suggest that the peptide–polysaccharide complexes have the potential to mimic the multifunctional basement membrane and may be useful for tissue engineering.     

Largely enhanced ductility of immiscible high density polyethylene/polyamide 6 blends via nano‐bridge effect of functionalized multiwalled carbon nanotubes

Immiscible polymer blends usually exhibit negative deviation in mechanical properties compared with the corresponding pure polymers due to the weak interfacial bonding between the two polymers. Due to the bridge effect of the oriented carbon nanotubes (CNTs) on the craze and crack development at the load of stress, CNTs have been proved to be efficient toughening agent for polymers. In this work, functionalized multiwalled carbon nanotubes (FMWCNTs) have been introduced into immiscible high density polyethylene/polyamide 6 (HDPE/PA6) blends through different sample preparation methods. The mechanical measurements demonstrate that, when the nanocomposite is prepared from the HDPE master batch, the sample exhibits excellent tensile strength and toughness simultaneously. For all the nanocomposites, FMWCNTs tend to migrate and/or maintain in PA6 particles, leading to the variation of the crystallization behavior in PA6 phase. Further results based on morphologies characterization indicate that the intensified interfacial adhesion between HDPE and PA6, which is realized by the nano‐bridge effect of FMWCNTs in the interfaces, is the main reason for the largely improved ductility. Copyright © 2010 John Wiley & Sons, Ltd.     

Poly(D,L-lactide)-block-poly(2-hydroxyethyl acrylate) block copolymers as potential biomaterials for peripheral nerve repair: in vitro and in vivo degradation studies

The properties of poly(D ,L ‐lactide)‐block‐poly(2‐hydroxyethyl acrylate) (PLA‐b‐PHEA) block copolymers by means of in vitro / in vivo (rat) degradation are investigated and compared to those of PLA homopolymer. Over 12 weeks, we observe mass loss and molecular weight decrease. In vitro and in vivo findings are very similar for each polymer tested. When a short PHEA block is used (PLA‐b‐PHEA 15 000–3 000 g · mol^?1, 85/15 wt%), the degradation process is found to be very similar to that of homo‐PLA, and to be typical of a bulk erosion mechanism, with no mass loss observed until week 7 and continuous decrease of molar mass within this timeframe. For a longer PHEA block length within the block copolymer (PLA‐b‐PHEA 15 000–7 500 g · mol^?1, 65/35 wt%), the degradation mechanism is modified, with a significant mass loss observed at early times and only a slight decrease in molar mass. The latter finding is related to the pronounced hydrophilicity and softness of the material induced by the PHEA block, which allow easy diffusion and rapid leakage of the degradation residues from the material towards the aqueous medium. Schwann cells are found to better adhere on spin‐coated films of PLA‐b‐PHEA (85/15 wt%) than on PLA ones. These results show the potential of such hydrophilized PLA‐based copolymers for use in peripheral nerve repair.