微水相中改性Ultrastable-Y分子筛固定化脂肪酶拆分(R,S)-2-辛醇

采用改性Ultrastable-Y分子筛固定化P. expansum PED-03脂肪酶(PEL), 利用固定化PEL在微水相中对(R,S)-2-辛醇进行拆分. 结果表明, 改性Ultrastable-Y分子筛固定化PEL所催化的拆分反应的转化率(c)和对映体过量值(e.e.)以及对映体选择性(E)均得到大幅度提高. 介质类型和体系含水量对酶促拆分反应有较大的影响. 在以正己烷为溶剂, 含水量为0.8%的体系中, 于50 ℃反应24 h的转化率(c)可达到理论值的97.68%, 对映体过量值(e.e.)可达到98.75%. 改性Ultrastable-Y分子筛固定化PEL催化效率高、立体选择性强, 且催化性能稳定, 在(R,S)-2-辛醇的酶法拆分方面具有良好的应用前景.     

Hydrogen peroxide in basic media for whole blood sample dissolution for determination of its lead content by electrothermal atomization atomic absorption spectrometry

Hydrogen peroxide in basic media is proposed as a means for dissolving whole blood samples to be analyzed by electrothermal atomization atomic absorption spectrometry, ET AAS. Approximately 2 g of the whole blood sample were directly weighed in a 150 mL volumetric flask; 3 mL of a NaOH 0.2 mol L⁻¹ solution, two drops of 1-octanol, as an antifoaming agent, and 1 mL of 30% volume hydrogen peroxide were added to the flask to promote oxidation. The solution was then manually shaken and after approximately three minutes of shaking, a clear solution, with no apparent suspended solids or greasy layers, was obtained. Distilled-deionized water was used to complete the volume. Ten μL of the resulting solution along with 10 μL of a solution containing 5000 mg L⁻¹ of NH₄H₂PO₄ and 300 mg L⁻¹ of Mg(NO₃)₂ as a modifier, were injected into transversely heated graphite tubes for lead determination. Both aqueous standards and standard addition calibration curves produced results not significantly different at a 95% confidence limit level. Accuracy of the measurements was assessed by analysis of the IAEA A-13 (concentration of trace and minor elements in freeze dried animal blood) standard reference material containing 0.18 mg L⁻¹ lead on a dry basis and by means of recovery tests. Analysis of the IAEA A-13 standard produced 0.17 ± 0.02 mg L⁻¹ lead on a dry basis; recovery tests afforded values from 95 to 105%. Ten consecutive measurements of a 5 ppb lead solution gave a characteristic mass of 47.2 pg and a (3S) detection limit of 1.77 μg L⁻¹ Pb. Results obtained from analysis of whole blood samples of volunteer donors covered a lead concentration range between 8 and 21 μg L⁻¹ with a mean value of 11.9 ± 4.7 μg L⁻¹.     

A Clean Synthesis of 1,4‐Diarylquinoline Derivatives Catalyzed by TEBAC in Aqueous Media

A series of 1,4‐diarylquinoline derivatives were synthesized by the reaction of arylmethylidenemalononitriles or 2‐cyano‐3‐aryl‐1‐acrylate and 3‐arylamino‐5,5‐dimethylcyclohex‐2‐enone in aqueous media at 100 °C catalyzed by TEBAC. Meanwhile, the water medium was chosen as green solvent.     

An Efficient Synthesis of Pyrazolo[3,4‐b]Pyridine Derivatives in Aqueous Media

A series of pyrazolo[3,4‐b]pyridines was synthesized by the reaction of 5‐aminopyrazole with benzylidenemalononitrile in aqueous media. The structures were characterized by IR, ¹H NMR, and elemental analysis and were further confirmed by X‐ray diffraction analysis.     

Electrochemical bromination of cyclic and acyclic enes using biphasic electrolysis

A simple method of electrochemical bromination of a series of cyclic and acyclic enes (styrene and substituted styrenes, stilbene, indene, and cyclooctene) in a biphasic water–chloroform mixture mediated by bromide/bromine redox system is reported. Aqueous 25% NaBr/H₂SO₄ is used as the electrolyte. Regio- and stereoselective dibromination of enes is achieved. Moderate to excellent yields of the product (83–98%) is obtained depending on the substrate. Electrolyte reuse has also been demonstrated successfully using HBr in the dibromination of styrene.     

Monodisperse Six-Armed Starbursts based on Truxene-Cored Multibranched Oligofluorenes: Design,Synthesis, and Stabilized Lasing Characteristics

A series of monodisperse six-armed conjugated starbursts ( Tr1F , Tr2F , and Tr3F ) containing a truxene core and multibranched oligofluorene bridges capped with diphenylamine (DPA) units has been designed, synthesized, and investigated as robust gain media for organic semiconductor lasers (OSLs). The influence of electron-rich DPA end groups on their optoelectronic characteristics has been discussed at length. DPA cappers effectively raise HOMO levels of the starbursts, thus enhancing the hole injection and transport ability. Solution-processed electroluminescence devices based on the resulting six-armed starbursts exhibited efficient deep-blue electroluminescence with clear reduced turn-on voltages (3.2–3.5 V). Moreover, the resulting six-armed molecules showed stabilized electroluminescence and amplified spontaneous emission with low thresholds (27.4–63.9 nJ pulse⁻¹), high net gain coefficients (80.1–101.3 cm⁻¹), and small optical loss (2.6–4.4 cm⁻¹). Distributed feedback OSLs made from Tr3F exhibited a low lasing threshold of 0.31 kW cm⁻² (at 465 nm). The results suggest that the construction of truxene-centered six-armed conjugated starbursts with the incorporation of DPA units can effectively enhance EL properties by precisely regulating the HOMO energy levels, and further optimizing their optical gain properties.     

Study on the enzymatic polymerization mechanism of lactone and the strategy for improving the degree of polymerization

Polymerization of several lactones were carried out by employing Pseudomonas sp. lipase as the catalyst. The data indicate that water is consumed at the onset of polymerization and released in part during subsequent stages, leading us to propose a complex mechanism for the enzymatic polymerization of lactone. This mechanism involves both ring‐opening and linear condensation polymerization. The former was dominant at the early stage while the latter was dominant in the later stage. In addition, the reaction media showed complex influences on enzymatic polymerization. Some organic solvents increased the degree of polymerization (DP) and decreased the molecular weight distribution. A strategy to increase the molecular weight of the polymer is introduced, which led to the synthesis of a polymer with a number‐average molecular weight (M_n) of 14,500—the highest M_n of poly(ε‐caprolactone) prepared by enzyme‐catalyzed polymerization thus far—and molecular weight distribution of 1.23. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1265–1275, 1999     

Detection of processed genetically modified food using CIM monolithic columns for DNA isolation

The availability of sufficient quantities of DNA of adequate quality is crucial in polymerase chain reaction (PCR)-based methods for genetically modified food detection. In this work, the suitability of anion-exchange CIM (Convective Interaction Media; BIA Separations, Ljubljana, Slovenia) monolithic columns for isolation of DNA from food was studied. Maize and its derivates corn meal and thermally pretreated corn meal were chosen as model food. Two commercially available CIM disk columns were tested: DEAE (diethylaminoethyl) and QA (quaternary amine). Preliminary separations were performed with standard solution of salmon DNA at different pH values and different NaCl concentrations in mobile phase. DEAE groups and pH 8 were chosen for further isolations of DNA from a complex matrix-food extract. The quality and quantity of isolated DNA were tested on agarose gel electrophoresis, with UV-scanning spectrophotometry, and by amplification with real-time PCR. DNA isolated in this way was of suitable quality for further PCR analyses. The described method is also applicable for DNA isolation from processed foods with decreased DNA content. Furthermore, it is more effective and less time-consuming in comparison with the existing proposed methods for isolation of DNA from plant-derived foods.     

Sol-gel approach to in situ creation of high pH-resistant surface-bonded organic-inorganic hybrid zirconia coating for capillary microextraction (in-tube SPME)

A novel zirconia-based hybrid organic-inorganic sol-gel coating was developed for capillary microextraction (CME) (in-tube SPME). High degree of chemical inertness inherent in zirconia makes it very difficult to covalently bind a suitable organic ligand to its surface. In the present work, this problem was addressed from a sol-gel chemistry point of view. Principles of sol-gel chemistry were employed to chemically bind a hydroxy-terminated silicone polymer (polydimethyldiphenylsiloxane, PDMDPS) to a sol-gel zirconia network in the course of its evolution from a highly reactive alkoxide precursor undergoing controlled hydrolytic polycondensation reactions. A fused silica capillary was filled with a properly designed sol solution to allow for the sol-gel reactions to take place within the capillary for a predetermined period of time (typically 15-30 min). In the course of this process, a layer of the evolving hybrid organic-inorganic sol-gel polymer got chemically anchored to the silanol groups on the capillary inner walls via condensation reaction. At the end of this in-capillary residence time, the unbonded part of the sol solution was expelled from the capillary under helium pressure, leaving behind a chemically bonded sol-gel zirconia-PDMDPS coating on the inner walls. Polycyclic aromatic hydrocarbons, ketones, and aldehydes were efficiently extracted and preconcentrated from dilute aqueous samples using sol-gel zirconia-PDMDPS coated capillaries followed by thermal desorption and GC analysis of the extracted solutes. The newly developed sol-gel hybrid zirconia coatings demonstrated excellent pH stability, and retained the extraction characteristics intact even after continuous rinsing with a 0.1 M NaOH solution for 24 h. To our knowledge, this is the first report on the use of a sol-gel zirconia-based hybrid organic-inorganic coating as an extraction medium in solid phase microextraction (SPME).     

Capillary zone electrophoretic studies of ion association between inorganic anions and tetraalkylammonium ions in aqueous-dioxane media

Ion association between inorganic anions and symmetrical tetraalkylammonium ions, R4N+ (R = Me, Et, Pr, n-Bu, n-Am, and 2-methyl butyl {isoamyl = iAm}) was investigated using ordinary silica capillary by capillary zone electrophoresis. An improved version of the Williams-Vigh method was used for the first time to measure the mobilities of the inorganic anions. Plots of log Kass against log dielectric constant in various media, revealed a smaller change in Kass compared to dielectric constant. These plots suggest that the Bjerrum's equation is inadequate in accounting for the associations of ions in a CZE setup.