Luminescence investigations of the GaP-based dilute nitride Ga(NAsP) material system

Multi-quantum well heterostructures (MQWHs) of the novel Ga(NAsP)/GaP material system have been grown, pseudomorphically strained to GaP-substrate. The crystalline perfection is verified by transmission electron microscopy (TEM). For As-concentrations in excess of about 70%, a direct band structure and adequate luminescence efficiency for laser device application is observed. Temperature-dependent photoluminescence (PL) investigations show the influence of carrier localisation and non-radiative recombination processes typical for dilute nitride materials. With rising N content in the active material, the emission wavelength shifts towards longer wavelength, leading to Ga(NAs)/GaP MQW structures with photon energies below the indirect band gap of silicon (Si). At the same time the luminescence intensity drops due to an increase in non-radiative carrier traps and/or structural degradation.     

计算机辅助物理实验教学的几点思考

探讨了物理实验教学引入智能化仪器的必要性和意义，指出引入计算机辅助教学必须对传统的实验教学内容和方法重新设计，同时软件的设计应给学生留有接口的余地。     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.     

一种新型可调谐锁模光纤激光器

利用法布里-珀罗腔的激光二极管作为调制器件，实现环形腔光纤激光器的主动锁模。并利用法布里-珀罗腔的激光二极管的多纵模特性，把激光二极管当作一梳状滤波器，通过偏振控制器来调整入射到激光二极管内光的偏振态，同时均衡腔内增益，得到波长大范围可调谐的锁模激光，其脉冲宽度约为48ps，脉冲重复速率2GHz。     

测距仪中新型的脉冲激光光源

针对现有测距仪中脉冲激光器存在寄生多脉冲的问题，提出并实现新型的采用同步泵浦声光调Q方法的测距仪用激光器、消除了寄生脉冲并提高了激光器的峰值功率。     

飞秒激光烧蚀研究进展

介绍飞秒激光烧蚀材料的机理论模型，阐述飞秒激光烧蚀的特性，揭示飞秒激光烧蚀的广泛应用前景。     

约束层对激光驱动冲击波压力影响机理的理论研究

针对刚性约束层、柔性约束层以及液体约束层，从激光诱导冲击波阵面状态、汽化物(包括气体和等离子体)扩散以及冲击波的反射进行分析，发现对于脉宽小于冲击波通过汽化物层的时间间隔的短脉冲激光，约束层并不能直接提高冲击波的冲量，而对于脉宽大于冲击波通过汽化层时间间隔的激光，其增强冲击效果是通过约束汽化物的扩散，提高压力幅值和由于冲击波在约束层与工件表面的多次反射而延长对工件的作用时间来实现的.刚性约束层能最大地增加冲击冲量，而柔性约束层和液体约束层的主要优点是其形状可与非平面形工件表面符合. 关键词： 激光 约束层 扩散 反射波     

激光二极管反馈干涉的实验观测

利用LabView软件虚拟示波器和信号源,观测了激光二极管反馈干涉实验现象．实验证明反馈回激光二极管的光的入射方向和入射光强以及信号处理电路的带宽,对反馈干涉信号有很大的影响．     

基于同步辐射加速器的康普顿背散射γ射线源(Ⅰ)产生MeV量级γ光子的数值计算

提出在筹建的上海同步辐射装置上建造一条MeV量级γ射线束及应用站,采用μm波长的红外(或远红外)激光与储存环中3.5GeV电子束进行康普顿背散射,从而获得能区为1—25MeV的康普顿背散射γ光子束,该光子束具有高强度、高极化度(线和圆极化)、准单色、方向性好的优点,可以广泛地应用于核物理和核天体物理基础研究及相关的应用研究领域.介绍了康普顿背散射的基本原理,并结合储存环参数给出了光子束性能的数值计算结果.     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.