时滞Rucklidge系统Hopf分岔分析与电路实现

以一类新的单时滞Rucklidge系统为分析对象,通过计算时滞系统的平衡点,分析该系统在各平衡点的稳定性和Hopf分岔的存在性,得到其发生Hopf分岔的条件。Matlab多组数值仿真验证了理论分析的正确性。基于此设计了一种可切换时滞与非时滞的混沌电路,并运用Multisim14.0进行仿真,实验结果表明,该电路可行且有效。     

CEV模型和B-P混合驱动模型下亚式期权Monte Carlo模拟

对亚式期权在CEV模型和B-P混合驱动模型限制下进行Monte Carlo模拟定价,建立风险中性测度,模拟出不同弹性因子值下资产价格路径.为了得出优于标准的Monte Carlo模拟,应用方差缩减技术来提高期权定价的精度.最后对亚式期权定价模型进行数值案例分析,得出弹性因子取值、时间步长、模拟次数与期权价值变化的关系.     

延性材料平面冲击波基本实验数值模拟的若干问题

假设屈服强度正比于剪切模量,分别构建了四种强度模型,并用于数值模拟Ly12铝的平面冲击波试验的质点速度剖面以及钨合金的平面冲击波试验的锰铜计应力记录.研究发现,基于Steinberg等的屈服强度模型比较符合实验.还对平面冲击波试验的层裂现象进行了简化的数值模拟,其中,采用了该文作者所提出的一种基于空穴聚集的层裂模型,该模型的特点是分别引入了层裂过程的早期及后期应力松弛方程.     

Computer Simulation Study on Adsorption and Conformation of Polymer Chains Driven by External Force

In this work, Monte Carlo simulations are used to study the critical adsorption behaviors of flexible polymer chains under the action of an external driving force F parallel to an attractive flat surface. The critical adsorption temperature T_c decreases linearly with increasing F,indicating that the driving force suppresses the adsorption of polymer. The conformation of polymer is also affected by the driving force.However, the effect of F is dependent on the competition between the driving force and temperature. Under strong force or at low temperature,the polymer is stretched along the direction of the force, while under weak force or at high temperature, the polymer is not stretched. When the force is comparable to the temperature, the polymer may be stretched perpendicular to the driving force, and below T_c, we observe conformational transitions from parallel to perpendicular and again to parallel by decreasing the temperature. We found that the perpendicular stretched conformation leads the polymer chain to synchronously move along the direction of the driving force. Moreover, the conformational transitions are attributed to the competition and cooperation between the driving force and the temperature.     

无线光通信中脉冲位置调制信号误码率的蒙特卡罗仿真

分析了在无线光通信链路中对激光脉冲应用脉冲位置调制的误码率,介绍了蒙特卡罗仿真方法的基本思想及其处理概率问题的方法步骤,并用蒙特卡罗仿真方法得到了脉冲位置调制信号的误码率.仿真结果表明,脉冲位置调制信号的误码率随入射光强的增大而减小,可用雪崩光电二极管对其进行探测以得到良好的接收性能.这对探讨脉冲位置调制光通信链路的系统特性和无线光通信接收系统的设计具有一定的参考价值.     

共焦显微镜扫描工作台的系统建模与动态分析

共焦显微镜扫描工作台动态模型是研究控制系统的重要依据,它直接影响工作台的重复定位精度.提出了将机械部分和电气部分分开建模的方法,建立了系统数学模型,该方法具有较好的可移植性,建模过程简单,有利于分析系统各环节对系统控制性能的影响.在MATLAB/Simulink下进行仿真,2 s内系统达到了稳定状态,证明了系统具有很好的动态特性,满足控制的要求.     

Simulation of Organic Liquid Product Deoxygenation through Multistage Countercurrent Absorber/Stripping Using CO2 as Solvent with Aspen-HYSYS: Process Modeling and Simulation

In this work, the deoxygenation of organic liquid products (OLP) obtained through the thermal catalytic cracking of palm oil at 450 °C, 1.0 atmosphere, with 10% (wt.) Na₂CO₃ as a catalyst, in multistage countercurrent absorber columns using supercritical carbon dioxide (SC-CO₂) as a solvent, with an Aspen-HYSYS process simulator, was systematically investigated. In a previous study, the thermodynamic data basis and EOS modeling necessary to simulate the deoxygenation of OLP was presented. This work addresses a new flowsheet, consisting of 03 absorber columns, 10 expansions valves, 10 flash drums, 08 heat exchanges, 01 pressure pump, and 02 make-ups of CO₂, aiming to improve the deacidification of OLP. The simulation was performed at 333 K, 140 bar, and (S/F) = 17; 350 K, 140 bar, and (S/F) = 38; 333 K, 140 bar, and (S/F) = 25. The simulation shows that 81.49% of OLP could be recovered and that the concentrations of hydrocarbons in the extracts of absorber-01 and absorber-02 were 96.95 and 92.78% (wt.) on a solvent-free basis, while the bottom stream of absorber-03 was enriched in oxygenated compounds with concentrations of up to 32.66% (wt.) on a solvent-free basis, showing that the organic liquid products (OLP) were deacidified and SC-CO₂ was able to deacidify the OLP and obtain fractions with lower olefin contents. The best deacidifying condition was obtained at 333 K, 140 bar, and (S/F) = 17.     

一种磁控管用扼流线圈仿真设计

采用电路仿真软件仿真滤波组件S参数曲线,观察曲线随器件参数的变化;介绍利用三维全波电磁仿真软件HFSS简化设计流程的方法,并与测试结果对比.结果 表明:利用3D仿真软件在满足器件设计精度的同时可以简化线圈的设计流程.     

新型Ku波段带通滤波器的设计

分析了传统滤波器设计方法的不足,提出一种增加薄电感膜片厚度来设计带通滤波器的方法,此方法可以有效降低滤波器的加工难度.通过电路特性分析和仿真软件HFSS的仿真计算,设计出了实际器件,测试结果验证了方法的正确性和可行性.     

LFM-CW雷达信号处理算法研究及仿真

从理论上对LFM-CW雷达进行信号分析,并对LFM-CW雷达的信号处理方法进行简单研究,最后通过仿真程序验证了该信号处理方法(距离/多普勒处理)在计算运动目标距离和速度时的正确性,为LFM-CW雷达信号处理提供了理论依据.