Toward Fuzzy Optimization without Mathematical Ambiguity

Fuzzy programming has been discussed widely in literature and applied in such various disciplines as operations research, economic management, business administration, and engineering. The main purpose of this paper is to present a brief review on fuzzy programming models, and classify them into three broad classes: expected value model, chance-constrained programming and dependent-chance programming. In order to solve general fuzzy programming models, a hybrid intelligent algorithm is also documented. Finally, some related topics are discussed.     

场协同理论在椭圆型流动中的数值验证

本文用数值模拟的方法，通过四个椭圆型流动传热的例子验证了场协同理论的正确性．结果表明，场协同理论不仅适合于抛物型流动，亦适合于复杂的有回流的椭圆型流动．     

机翼大攻角下失速颤振的气动弹性研究

本文采用流固耦合的数值方法研究了机翼在0°～50°攻角下的颤振。计算结果表明,随着来流攻角α0的增大,机翼的固有频率对颤振的影响越来越大,颤振由线性的强迫振动逐渐发展成为非线性的自激振动,而当α0增加到一定程度以后,大尺度分离流交替地从机翼头部和尾部产生,机翼和流场会发生共振,引起机翼的失速颤振。     

1+1/2对转涡轮叶排轴向间距对性能影响的研究

木文对1+1/2对转涡轮中轴向间距影响进行了初步研究。对不同轴向间距叶栅流场进行了大量时间精确模拟。研究表明,1+1/2对转涡轮高低压转叶间轴向间距成为追求高效率的制约因素,轴向间距为高压转叶喉部宽度是关键点。因此有关小轴向间距下强激波/叶排干扰的研究应该加强。     

轴流风扇叶片端导叶作用的研究

本文采用数值方法研究了叶片端导叶对轴流风扇性能的影响。通过与普通开式轴流风扇比较,分析了叶片端导叶对内部流动作用的机理.数值计算结果表明:叶片端导叶的安装位置将影响轴流风扇气动效率,安装叶片端导叶不能提高风扇静压升,但是在压力面安装时能有效地减小风扇叶顶泄漏流与主流的掺混损失;在设计流量下,压力面安装叶片端导叶使泄漏涡的作用范围较小,涡核更靠近吸力面;吸力面安装叶片端导叶弱化了泄漏涡的强度但没有减小泄漏涡的作用范围。     

CDMA通信系统的MATLAB仿真

在简要介绍MATLAB语言的基础上，对使用MATLAB语方仿真的CDMA通信系统进行描述。     

Tensile behaviour of corroded and hydrogen embrittled 2024 T351 aluminum alloy specimen

The synergetic effect of corrosion and corrosion induced hydrogen embrittlement damage processes which occur at local scale has been found to result in a dramatic macroscopic tensile ductility loss of the 2024 aluminum alloy. In the present work, the tensile behaviour of corroded 2024 T351 specimens has been estimated on the basis of FE analysis by taking into account the local material properties in the damaged areas. A parametric study is involved to account for the effect of thickness in the results. Calculated tensile properties obtained with the analysis agree well with experimental data.     

Mathematical Modeling, Control, Computer Simulation and Laboratory Experiments of a Spatial Servopneumatic Parallel Robot

In this paper, the special construction of a parallel robot, called spatial servopneumatic multi-axis test facility, will be discussed. The investigations include the following aspects: (i) the laboratory set-up of the robot, (ii) various results obtained in laboratory experiments, taking into account quite different control algorithms and command-input signals, (iii) a comparison of the laboratory experiments with the computer simulations of Part I of this paper, and ({vi}) a quality check of the results compared with the cost of the different controller realizations. The results of both the computer simulations and the laboratory experiments show: (i) The dynamic behavior of the parallel structure can be tremendously improved by using sophisticated nonlinear control algorithms. (ii) This improvement has to be paid by a drastically increased amount of work for deriving the model equations and control algorithms, and by augmented hardware cost of the sensing elements and controller electronics. (iii) Carefully developed model equations and identified model parameters provide theoretical models of the complex parallel structure that are very close to reality. This enables the design engineer to systematically investigate constructive alternatives of the design parameters, sensor and actuator concepts, and control strategies of the MAP prior to their hardware realization.This work has been supported by the German Science Foundation (DFG) under Contract No. Ha 1666/6-3.     

基于Multisim8的压控振荡电路仿真分析

介绍了Multisim8的仿真功能的特点，并通过实例说明了用Multisim8进行仿真分析的具体方法，简单介绍了如何设置参数和进行仿真操作。     

基于Protel DXP的电路仿真设计

Protel DXP是集所有设计工具于一身的电子设计自动化(EDA)软件.文中运用其内嵌的仿真器叙述了分压式偏置电路放大器的仿真设计过程,设计过程简单、方便.在电子线路理论教学过程中引入电路设计仿真环节在不同情况下对电路进行实时分析,不仅可以提高学生的学习兴趣,而且能够在较短时间内加深学生对理论知识的理解;在工程设计过程中利用仿真工具对电路进行即时测试,可以缩短设计周期,提高设计效率.