企业信息化建设中的问题及对策

我国企业在信息化建设过程中取得了一些成果 ,也出现了不少问题 ,本文主要针对这种现状 ,指出了企业存在的一些问题 ,并就信息系统开发、维护和集成 ,提出了一些建议。     

STI process steps for sub-quarter micron CMOS

This paper presents Shallow Trench Isolation (STI) process steps for sub-1/4 μ CMOS technologies. Dummy active areas, vertical trench sidewalls, excellent gap filling, counter mask etch step and CMP end point detection, have been used for a 0.18 μm CMOS technology. Electrical results obtained with a 5.5 nm gate oxide thickness show good isolation down to 0.3 μm spacing. Good transistor performances have been demonstrated.     

Finite element modal solutions of planar photonic crystal fibers with rectangular air-holes

Modal solutions of planar photonic crystal waveguides with rectangular air-holes are presented by using a rigorous full-vectorial finite element-based approach. The effective indices, mode field profiles, spot-sizes, power confinements, modal hybridness, beat lengths and group velocity dispersions are shown for the fundamental and higher order modes of the quasi-TE and TM polarizations.     

Simulation and fabrication of carbon nanotubes field emission pressure sensors

A novel field emission pressure sensor has been achieved utilizing carbon nanotubes (CNTs) as the electron source. The sensor consists of the anode sensing film fabricated by wet etching process and multi-wall carbon nanotubes (MWNTs) cathode in the micro-vacuum chamber. MWNTs on the silicon substrate were grown by thermal CVD. The prototype pressure sensor has a measured sensitivity of about 0.17-0.77 nA/Pa (101-550 KPa). The work shows the potential use of CNTs-based field-emitter in microsensors, such as accelerometers and tactile sensors.     

Performance and simulation of an on-board guided-wave optical processor for airborne SAR applications

This paper describes the performance and simulation of a compact integrated optical processor for the real-time reconstruction of two-dimensional images in airborne stripmap synthetic aperture radar applications. The functional behavior of the processor is explained in some detail. The design criteria are briefly given. The simulation step allowed the main processor characteristics and properties to be identified. A number of comparisons were obtained in airborne SAR mission scenarios between the predictions of the optical device and those achieved by the modern electronic digital approach, based on the wavefront reconstruction method by matched filtering.     

高斯光束计算平板波导自由传输区远场分布及其修正

对近轴近似条件下求解亥姆霍兹方程得到的高斯光束显式传播公式做了分析，同时，基于基尔霍夫衍射理论，在菲涅耳近似的条件下给出了相应的高斯光束在远场的传播公式，在此基础上，对近轴近似条件做出了定量分析，给出了这个近似条件引入的误差，提出了一种计算高斯光束远场分布的修正方法，并采用有限差分-光束传播方法(FD-BPM)来检验各种方法的准确性。把这种修正方法应用到平面光集成波导器件，如阵列波导光栅(AWG)、蚀刻衍射光栅(EDG)等器件的设计和模拟中，可以大大降低工作的复杂性，同时可以得到精确的结果。     

Optimal Path Planning Based on Visibility

Various problems associated with optimal path planning for mobile observers such as mobile robots equipped with cameras to obtain maximum visual coverage of a surface in the three-dimensional Euclidean space are considered. The existence of solutions to these problems is discussed first. Then, optimality conditions are derived by considering local path perturbations. Numerical algorithms for solving the corresponding approximate problems are proposed. Detailed solutions to the optimal path planning problems for a few examples are given.     

Tunable narrow-band infrared emitters from hexagonal lattices

In this work, we present both the theoretical basis as well as supporting experimental measurements for development of a novel mid-infrared thermally stimulated narrow band emitter with a spectral bandwidth of less than 10%. To achieve this, we utilize a metallized-surface 2D photonic crystal of air voids in a silicon background with hexagonal structure symmetry. Our results are based on the generation of discrete surface plasmon (SP) modes in the thin metallized layer residing on the top surface. This yields a series of adequately spaced discrete peaks in the reflection spectrum, dominated by a single sharp feature corresponding to the lowest plasmon order, in an otherwise uniform highly reflective spectrum (>90%) over most of the IR spectrum. This, in turn, gives rise to a sharp absorption feature with a correspondingly narrow thermal emission peak in the emission spectrum. Transfer matrix calculations simulate well both the position and strengths of the absorption peaks. By altering the period of the surface photonic lattice, the SP peak and emissive band can be tuned to the desired wavelength. These devices promise a new class of tunable infrared emitters with high power in a narrow spectral bandwidth. Such narrow band sources are critical to achieving high efficiency gas sensors.     

舰艇电子战综合对抗系统应用探讨

通过对现代海上电子战特点深刻探讨。分析了现代海战条件对舰船电子战对抗能力需求。并对现代舰船电子战综合对抗系统所采用的新技术情况进行探讨。     

Layout-Specific Circuit Evaluation in 3-D Integrated Circuits

In this paper, we describe a comprehensive layout methodology for bonded three-dimensional integrated circuits (3D ICs). In bonded 3D integration technology, parts of a circuit are fabricated on different wafers, and then, the wafers are bonded with a glue layer of Cu or polymer based adhesive. Using our layout methodology, designers can layout such 3D circuits with necessary information on inter-wafer via/contact and orientation of each wafer embedded in the layout. We have implemented the layout methodology in 3DMagic. Availability of 3DMagic has led to interesting research with a wide range of layout-specific circuit evaluation, from performance comparison of 2D and 3D circuits to layout-specific reliability analyses in 3D circuits. Using 3DMagic, researchers have designed and simulated an 8-bit encryption processor mapped into 2D and 3D FPGA layouts. Moreover, the layout methodology is an essential element of our ongoing research for the framework of a novel Reliability Computer Aided Design tool, ERNI-3D.