胃肠道激光内镜应用技术

本文结合作者的体验和文献，详细介绍了激光光导纤维检查与准备，激光内镜在胃肠道疾病应用的技巧、方法和注意事项等，可为临床医生和相关技术人员提供帮助。     

Effect of the Parameters of Three-Mirror Resonators on the Spectral Characteristics of Single-Pulse Laser Generation with Self-Injection of Priming Radiation

Based on a semiclassical theory, investigations were made of the dynamics and spectral composition of pulsed generation with self-injection of priming radiation from the active part of a three-mirror linear resonator, the passive part of which contains an active loss modulator and serves as the output reflector of the laser. It is shown that there exists a range of resonator parameters at which pulsed lasing has virtually a single frequency irrespective of the detuning of the frequencies of the priming radiation and of the nearest eigenmode of the composite resonator. Considering graphically the phase conditions of generation, it is established that among pulsed lasers with self-injection of priming radiation which are constructed on the basis of three-mirror linear and branched resonators, the most efficient for creating single-frequency generation are those in which the length of the main resonator, where generation of the pulse occurs, is larger than the length of the additional one intended for forming the priming radiation. With an inverse ratio of the lengths of the resonators, the conditions of single-frequency pulsed generation becomes dependent on the priming radiation frequency.     

Novel model of FM-noise conversion in a UMZI using RF external phase modulation of lasers: Theoretical and experimental results

In this paper, we propose and demonstrate a new and original model for theoretical calculation and experimental measurement of the noise power spectral density (NPSD) in phase-modulated optical links. The phase modulation is operated in the RF frequency range by an external phase modulator. The NPSD is derived for the first time in interferometric systems, by considering all effects such as the 1/f FM noise of the laser and white noise applied to light from a 1550 nm DFB laser, with phase modulation. The results show for the first time the influence of the phase modulation index, modulation frequency and interferometric delay in the phase-to-intensity noise conversion. The experimental and simulation results of conversion of FM-noise to intensity noise in an optical link by considering the external RF phase modulation are shown with good agreement.     

在BEPC上建造γ束线站的分析

考虑电子的反冲并利用康普顿散射,研究了激光同步辐射光源(LSS)辐射的光子波长、光子能量。结果表明,对于不同的γ,LSS辐射的光子波长和能量有不同的近似公式。当γ<<λ1/4λe时,LSS辐射的光子波长λ2≈λ1/4γ2,能量(εc2≈4γ2εc1;当γ>>λ1/4λe时,LSS辐射的光子波长λ2≈λe/γ,能量cε2≈m0γc2;结果表明,LSS辐射的条件是种子激光的波长λ1大于电子的物质波波长λm;LSS辐射的极值波长是λ2m ax=h/m0γv,极值能量是cε2m ax=βeε;本文后半部分提出了利用北京正负电子对撞机的强流高亮度电子束与激光的康普顿背散射产生单色γ射线的建议。     

红外热像仪参数的双黑体测量装置

对红外热像仪参数双黑体测量装置的工作原理进行了介绍。装置采用双黑体及反射型靶标为温差辐射源，可实现黑体温度温差准直辐射的定期校准和红外热像仪参数测量量值的溯源，也可实现红外热像仪参数的可控性，以及对它进行稳定的、可复现的精确测量。推导出利用红外热像仪参数双黑体测量装置测量信号传递函数SiTF数学模型，分析了红外热像仪参数测量装置的客观因素——仪器常数，针对仪器常数对SiTF测量的影响进行了试验。试验结果表明，仪器常数对红外热像仪SiTF参数测量精度影响较大，并同时影响时域与空域NETD及3D噪声的准确测量。     

Diode-pumped 671 nm laser frequency doubled by CPM LBO

A design of diode-pumped high-efficiency Nd:YVO₄/LBO red laser is reported. Using critical phase-matching (CPM) LBO, 671 nm red laser was obtained from 1342 nm light by intracavity frequency doubling. With an incident pump laser of 800 mW, using type-I and type-II CPM LBO, 97 and 52 mWTEM₀₀ mode red laser outputs were obtained, with optical-to-optical conversion efficiencies of up to 12.1% and 6.5%, respectively.     

动态激光衍射法测量细丝直径

基于夫琅禾费衍射理论和巴比涅互补原理,提出了利用激光衍射对细丝直径进行动态测量的方法.该方法具有测量精度高、速度快、非接触、使用方便且易于微机联接实现自动化测量等优点.     

The influence of pulse duration on the stress levels in ablation of ceramics: A finite element study

We present a finite element model to investigate the dynamic thermal and mechanical response of ceramic materials to pulsed infrared radiation. The model was applied to the specific problem of determining the influence of the pulse duration on the stress levels reached in human dental enamel irradiated by a CO₂ laser at 10.6 μm with pulse durations between 0.1 and 100 μs and sub-ablative fluence. Our results indicate that short pulses with durations much larger than the characteristic acoustic relaxation time of the material can still cause high stress transients at the irradiated site, and indicate that pulse durations of the order of 10 μs may be more adequate both for enamel surface modification and for ablation than pulse durations up to 1 μs. The model presented here can easily be modified to investigate the dynamic response of ceramic materials to mid-infrared radiation and help determine optimal pulse durations for specific procedures.     

Spectral and temporal characteristics of metallic nanoparticles produced by femtosecond laser pulses

We study the time of flight optical emission from titanium and tungsten nanosized particles, generated through femtosecond laser-matter interaction in vacuum, in the wavelength spectral range from 300 to 900 nm. Typical spectra consist of broadband structureless signals similar to black body emission from a macroscopic object. Nanoparticles temperature, deduced from their emission spectra, decreases drastically as a function of their time of arrival at a given distance from the target. This behaviour is seen to be independent of individual particle velocities.     

Fluorescence and absorption of polystyrene exposed to UV laser radiation

We show that when polystyrene is exposed (for 15–60 sec) to a UV laser light beam (λ = 248 nm), its absorption and luminescent properties change significantly. In the irradiated polymer, optical centers are formed with absorption bands in the 280–460 nm region and fluorescence bands in the 330–520 nm region. We have established the chemical structure of the optical centers for fluorescence of polystyrene. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 1, pp. 54–58, January–February, 2006.