激光除冰研究

架空输送电线路因覆冰而导致的事故危害性很大,本文总结了目前国内外输电线路导线覆冰的现状。统计国内外探索出来的各种预防,融化,除冰等很多解决方案。通过研究和探讨,分析导线覆冰的传热和能量,运用了多种激光器进行激光熔(除)冰实验,比较研究二氧化碳激光器的除冰情况。以及提出激光熔冰的方法、研究方向和前景。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

Effect of the Parameters of Three-Mirror Resonators on the Spectral Characteristics of Single-Pulse Laser Generation with Self-Injection of Priming Radiation

Based on a semiclassical theory, investigations were made of the dynamics and spectral composition of pulsed generation with self-injection of priming radiation from the active part of a three-mirror linear resonator, the passive part of which contains an active loss modulator and serves as the output reflector of the laser. It is shown that there exists a range of resonator parameters at which pulsed lasing has virtually a single frequency irrespective of the detuning of the frequencies of the priming radiation and of the nearest eigenmode of the composite resonator. Considering graphically the phase conditions of generation, it is established that among pulsed lasers with self-injection of priming radiation which are constructed on the basis of three-mirror linear and branched resonators, the most efficient for creating single-frequency generation are those in which the length of the main resonator, where generation of the pulse occurs, is larger than the length of the additional one intended for forming the priming radiation. With an inverse ratio of the lengths of the resonators, the conditions of single-frequency pulsed generation becomes dependent on the priming radiation frequency.     

在BEPC上建造γ束线站的分析

考虑电子的反冲并利用康普顿散射,研究了激光同步辐射光源(LSS)辐射的光子波长、光子能量。结果表明,对于不同的γ,LSS辐射的光子波长和能量有不同的近似公式。当γ<<λ1/4λe时,LSS辐射的光子波长λ2≈λ1/4γ2,能量(εc2≈4γ2εc1;当γ>>λ1/4λe时,LSS辐射的光子波长λ2≈λe/γ,能量cε2≈m0γc2;结果表明,LSS辐射的条件是种子激光的波长λ1大于电子的物质波波长λm;LSS辐射的极值波长是λ2m ax=h/m0γv,极值能量是cε2m ax=βeε;本文后半部分提出了利用北京正负电子对撞机的强流高亮度电子束与激光的康普顿背散射产生单色γ射线的建议。     

Diode-pumped 671 nm laser frequency doubled by CPM LBO

A design of diode-pumped high-efficiency Nd:YVO₄/LBO red laser is reported. Using critical phase-matching (CPM) LBO, 671 nm red laser was obtained from 1342 nm light by intracavity frequency doubling. With an incident pump laser of 800 mW, using type-I and type-II CPM LBO, 97 and 52 mWTEM₀₀ mode red laser outputs were obtained, with optical-to-optical conversion efficiencies of up to 12.1% and 6.5%, respectively.     

大口径宽视场双波段扫描红外相机光学设计

通过分析计算,设计了一种大口径宽视场折射式红外相机光学系统。该系统设计用于超长线阵扫描红外相机的地面演示成像,它能同时对短波2μm—3μm、中波3μm—4.5μm双波段成像,且同时具有24°的大视场和150mm的宽口径,成像质量接近衍射极限。该系统在航天遥感领域应用广泛。     

Luminescence investigations of the GaP-based dilute nitride Ga(NAsP) material system

Multi-quantum well heterostructures (MQWHs) of the novel Ga(NAsP)/GaP material system have been grown, pseudomorphically strained to GaP-substrate. The crystalline perfection is verified by transmission electron microscopy (TEM). For As-concentrations in excess of about 70%, a direct band structure and adequate luminescence efficiency for laser device application is observed. Temperature-dependent photoluminescence (PL) investigations show the influence of carrier localisation and non-radiative recombination processes typical for dilute nitride materials. With rising N content in the active material, the emission wavelength shifts towards longer wavelength, leading to Ga(NAs)/GaP MQW structures with photon energies below the indirect band gap of silicon (Si). At the same time the luminescence intensity drops due to an increase in non-radiative carrier traps and/or structural degradation.     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.     

测距仪中新型的脉冲激光光源

针对现有测距仪中脉冲激光器存在寄生多脉冲的问题，提出并实现新型的采用同步泵浦声光调Q方法的测距仪用激光器、消除了寄生脉冲并提高了激光器的峰值功率。