Selective area epitaxy of CdTe

We have performed selective area epitaxy (SAE) of CdTe layers grown by molecular beam epitaxy using a shadow mask technique. This technique was chosen over other SAE techniques due to its simplicity and its compatibility with multiple SAE patterning steps. Features as small as 50 microns × 50 microns were obtained with sharp, abrupt side walls and flat mesa tops. Separations between mesas as small as 20 microns were also obtained. Shadowing effects due to the finite thickness of the mask were reduced by placing the CdTe source in a near normal incidence position. Intimate contact between the mask and the substrate was essential in order to achieve good pattern definition.     

Formation of GaAsP interface layers monitored by reflectance anisotropy spectroscopy

Reflectance anisotropy spectroscopy (RAS) has been used to study As-by-P exchange during metalorganic vapor phase epitaxy. The study focuses on the processes occurring during switching from GaAs to GaInP, especially the effect of purging PH₃ over a GaAs surface. GaAsP/GaAs superlattices of different periodicity were grown and the P-content was determined by high-resolution x-ray diffraction and correlated to the RAS spectra. From the temperature dependence of the P-content, an activation energy of 0.56 eV was estimated for the incorporation mechanism. In addition to the insights into the processes at mixed group-V heterointerfaces, our study demonstrates the reproducibility of RAS transients that thus can be used for process monitoring.     

本征吸除硅片特性研究

本文描述硅本征吸杂片的特性参数,如吸除区宽度、洁净度,氧沉淀密度、MOS电容寿命,介绍了表面态密度及残余间隙氧浓度的检测方法和工艺对参数的影响及参数之间的内在联系,文章还实验论证了不同参数水平对器件成品率的影响,建立了以MOS电容寿命为主导的参数控制方法,利用本文提供的控制参数,可使CCD-512器件成品率达60％,以上优品率≥85％。     

Rapid thermal chemical vapor deposition of in-situ boron doped polycrystalline SIxGe1-x

In-situ doped polycrystalline Si_xGe_1-x (x = 0.7) alloys were deposited by rapid thermal chemical vapor deposition (RTCVD) using the reactive gases SiH₂Cl₂, GeH₄ and B₂H₆ in a H₂ carrier gas. The depositions were performed at a total pressure of 4.0 Torr and at temperatures 600° C, 650° C and 700° C and different B₂H₆ flow rates. The conditions were chosen to achieve high doping levels in the deposited films. Our results indicate negligible effect of B₂H₆ flow on the deposition rate. The depositions follow an Arrhenius type behavior with an activation energy of 25 kcal/mole. Boron incorporation in the films was found to follow a simple kinetic model with higher boron levels at lower deposition rates and higher B₂H₆ flow rates. As-deposited resistivities as low as 2 mΩ-cm were obtained. Rapid thermal annealing (RTA) in the temperature range 800-1000° C was found to reduce the resistivity only marginally due to the high levels of boron activation achieved during the deposition process. The results indicate that polycrystalline Si_xGe_1-x films can be deposited by RTCVD with resistivities comparable to those reported for in-situ doped polysilicon.     

Parallelization of population-based multi-objective meta-heuristics: An empirical study

In single-objective optimization it is possible to find a global optimum, while in the multi-objective case no optimal solution is clearly defined, but several that simultaneously optimize all the objectives. However, the majority of this kind of problems cannot be solved exactly as they have very large and highly complex search spaces. Recently, meta-heuristic approaches have become important tools for solving multi-objective problems encountered in industry as well as in the theoretical field. Most of these meta-heuristics use a population of solutions, and hence the runtime increases when the population size grows. An interesting way to overcome this problem is to apply parallel processing. This paper analyzes the performance of several parallel paradigms in the context of population-based multi-objective meta-heuristics. In particular, we evaluate four alternative parallelizations of the Pareto simulated annealing algorithm, in terms of quality of the solutions, and speedup.     

Adhesion studies of latex film surfaces on the meso- and nanoscale

In this paper the effects of surface roughness and annealing temperature (T) of latex coating films on adhesion are discussed for the different stages of the film formation process. The surface free energy of latex films was assessed in terms of practical work of adhesion (W) (or adherence) using a custom-built adhesion-testing device (ATD), atomic force microscopy (AFM), and contact angle measurements. For preannealed latex films surface roughness averages (R_a) were determined from AFM height images and were related to the values of W obtained from ATD measurements at room temperature. The results obtained using these tests exhibiting surface behavior on different length scales indicate a dependence of the measured adhesion on surface roughness and temperature, as well as on the length scale of the measurements.First preannealed samples were studied, which were obtained by heat treatment above the respective glass transition temperatures (T_g). Increasing the temperature of preannealing resulted in a decrease of the adherence observed in ATD experiments at room temperature. However, on the nanoscale, using AFM, no significant variation of the adherence was observed. This observation can be explained by roughness arguments. Preannealing decreases roughness which results in lower adherence values measured by ATD while for essentially single asperity AFM experiments roughness has an insignificant effect. Specimens were also annealed over a constant period of time (90 min) at different temperatures. At the end of the heat treatment, adhesion was measured at the treatment temperature by ATD. The amplified effect of temperature observed in this case on adherence is attributed to the combination of roughness decrease and increasing test temperature. In a third set of experiments completely annealed samples were studied by ATD as well as by AFM as a function of temperature. With increasing T values ATD showed a decrease in adherence, which is attributed to a decreasing surface free energy of the annealed films at elevated T values. AFM, on the other hand, showed an opposite trend which is assigned to increasing penetration of the tip into the tip/wetting polymer samples versus increasing temperature. Finally, annealing isotherms as a function of time were investigated by ATD in situ at different temperatures. This last set of experiments allowed us to optimize annealing time and temperature to achieve complete curing.     

模拟退火法在吸收薄膜的椭偏反演算法中的应用

将一种广泛用于求解复杂系统优化问题的技术－－模拟退火法－－用来求解椭偏反演方程。首先假设一个薄膜模型，计算出其相应的椭偏参数（Ψ，Δ）的值，在这个计算值的基础上加入不同标准偏差的高斯噪声；然后将加入噪声后的值（Ψm,Δm)作为模拟的测量数据，采用模拟退火算法进行求解，验证得知这种方法求得的薄膜参数很接近于假设的薄膜模型参数的真值，与其他文献的报道结果一致，而且在扩大搜寻范围时，仍然可以得到准确解，从而证明了该方法的可行性以及有效性。     

Parking Capacity and Pricing in Park'n Ride Trips: A Continuous Equilibrium Network Design Problem

In this paper we consider the problem of designing parking facilities for park'n ride trips. We present a new continuous equilibrium network design problem to decide the capacity and fare of these parking lots at a tactical level. We assume that the parking facilities have already been located and other topological decisions have already been taken.The modeling approach proposed is mathematical programming with equilibrium constraints. In the outer optimization problem, a central Authority evaluates the performance of the transport network for each network design decision. In the inner problem a multimodal traffic assignment with combined modes, formulated as a variational inequality problem, generates the share demand for modes of transportation, and for parking facilities as a function of the design variables of the parking lots. The objective is to make optimal parking investment and pricing decisions in order to minimize the total travel cost in a subnetwork of the multimodal transportation system.We present a new development in model formulation based on the use of generalized parking link cost as a design variable.The bilevel model is solved by a simulated annealing algorithm applied to the continuous and non-negative design decision variables. Numerical tests are reported in order to illustrate the use of the model, and the ability of the approach to solve applications of moderate size.     

退火温度对低温生长MgxZn1－xO薄膜光学性质的影响

用射频磁控溅射法在80℃衬底温度下制备出Mg_xZn_1-xO(x=0.16)薄膜，用X射线衍射(XRD)、光致发光(PL)和透射谱研究了退火温度对Mg_xZn_1-xO薄膜结构和光学性质的影响.测量结果显示，Mg_xZn_1-xO薄膜为单相六角纤锌矿结构，并且具有沿c轴的择优取向；随着退火温度的升高，(002)XRD峰强度、平均晶粒尺寸和紫外PL峰强度增大，(002)XRD峰半高宽(F 关键词： xZn_1-xO薄膜')" href="#">Mg_xZn_1-xO薄膜 射频磁控溅射 退火     

Analysis of Static Simulated Annealing Algorithms

Generalized hill climbing (GHC) algorithms provide a framework for modeling local search algorithms to address intractable discrete optimization problems. This paper introduces a measure for determining the expected number of iterations to visit a predetermined objective function level, given that an inferior objective function level has been reached in a finite number of iterations. A variation of simulated annealing (SA), termed static simulated annealing (S²A), is analyzed using this measure. S²A uses a fixed cooling schedule during the algorithm execution. Though S²A is probably nonconvergent, its finite-time performance can be assessed using the finite-time performance measure defined in this paper.