Anvendung und Perspektiven der Strahlungsvernetzung in der Volkswirtschaft der DDR

Zum angegebenen Thema wurde vom Zentralinstitut für Festkörperphysik und Werkstofforschung der Akademie der Wissenschaften der DDR (ZfFW) gemeinsam mit dem Bezirksvorstand Dresden der Kammer der Technik am 9. 10. 1975 ein Tageskolloquium veranstaltet. Es wurden 100 Teil-nehmer registriert, wobci Kombinate und Betriebe zur Anwendung von Plasten und Elasten stark vertreten waren.     

Survey of deep sub-barrier heavy-ion fusion hindrance phenomenon forpositive and negative Q-value systems using the proximity-type potential

A systematic survey of the accurate measurements of heavy-ion fusion cross sections at extreme sub-barrier energies is performed using the coupled-channels (CC) theory that is based on the proximity formalism. This work theoretically explores the role of the surface energy coefficient and energy-dependent nucleus-nucleus proximity potential in the mechanism of the fusion hindrance of 14 typical colliding systems with negative \begin{document}$Q$\end{document}-values, including ¹¹B+¹⁹⁷Au, ¹²C+¹⁹⁸Pt, ¹⁶O+²⁰⁸Pb, ²⁸Si+⁹⁴Mo, ⁴⁸Ca+⁹⁶Zr, ²⁸Si+⁶⁴Ni, ⁵⁸Ni+⁵⁸Ni, ⁶⁰Ni+⁸⁹Y, ¹²C+²⁰⁴Pb, ³⁶S+⁶⁴Ni, ³⁶S+⁹⁰Zr, ⁴⁰Ca+⁹⁰Zr, ⁴⁰Ca+⁴⁰Ca, and ⁴⁸Ca+⁴⁸Ca, as well as five typical colliding systems with positive \begin{document}$Q$\end{document}-values, including ¹²C+³⁰Si, ²⁴Mg+³⁰Si, ²⁸Si+³⁰Si, ³⁶S+⁴⁸Ca, and ⁴⁰Ca+⁴⁸Ca. It is shown that the outcomes based on the proximity potential along with the above-mentioned physical effects achieve reasonable agreement with the experimentally observed data of the fusion cross sections \begin{document}$\sigma_{\rm{fus}}(E)$\end{document}, astrophysical \begin{document}$S(E)$\end{document} factors, and logarithmic derivatives \begin{document}$L(E)$\end{document} in the energy region far below the Coulomb barrier. A discussion is also presented on the performance of the present theoretical approach in reproducing the experimental fusion barrier distributions for different colliding systems.     

P原子的光学模型势与核极化修正

基于SIC-X_α的较为严格的计算方法,对于Rydberg电子态的交换参数采用自洽场模型计算核极化,结果比文献[15[的计算方法要精确.另外文献[15]在计算P²³⁸U的能级跃迁时,模型还不够完善,存在着难以克服的弊端,计算结果也不可能准确.20世纪70年代初,Batty就进行强相互作用势模型的研究,经过二十几次不断探索与改进,在1997—2000年给出了光学模型势的正确形式.对Rydberg电子态的交换参数采用自洽场模型计算核极化,用以修正Batty光学模型势下的P²³⁸U能级跃迁,得到反质子原子的相应能级.结果与实验数据相当符合.连同π^-,K^-,∑^-,Ξ^-原子的情况支持了Batty光学模型势在描写核子间强相互作用的正确性,同时也表明计算核极化的方法是正确的,为反粒子原子及奇特原子的深入研究及应用提供了理论依据.     

Impact of substrate injected hot electrons on hot carrier degradation in a 180-nm NMOSFET

Although hot carriers induced degradation of NMOSFETs has been studied for decades, the role of hot electron in this process is still debated. In this paper, the additional substrate hot electrons have been intentionally injected into the oxide layer to analyze tile role of hot electron in hot carrier degradation. The enhanced degradation and the decreased time exponent appear with the injected hot electrons increasing, the degradation increases from 21.80% to 62.00% and the time exponent decreases from 0.59 to 0.27 with Vb decreasing from 0 V to -4 V, at the same time, the recovery also becomes remarkable and which strongly depends on the post stress gate bias Vg. Based on the experimental results, more unrecovered interface traps are created by the additional injected hot electron from the breaking Si-H bond, but the oxide trapped negative charges do not increase after a rapid recovery.     

高强度钢板热成形本构理论与实验分析

热成形(热冲压)过程中硼钢的热、力、相变耦合关系是研究热成形理论的基础, 同时也是决定热成形工艺及数值模拟准确性的关键因素. 对热成形硼钢进行高温拉伸及淬火实验: 硼钢板材试样在奥氏体化(950℃)后保温一定时间, 然后在连续冷却的同时施加拉伸力, 记录此过程中力、位移、膨胀量及温度的变化. 通过对不同冷却速率及不同拉伸力情况下上述物理量的变化规律及微观组织性能的分析, 研究硼钢相变过程中的热、力、相变耦合关系. 建立了硼钢相变过程中的热、力、相变耦合模型. 通过引入混合定律对热成形过程中的多相材料热力学参数和力学性能进行等效分析; 对热成形应变组成及其形成机理进行了分析, 引入了相变体积应力及相变塑性应力等新概念. 硼钢高温流动应力采用修改的Norton-Hoff形式, 并通过实验确定了流动应力的材料常数. 在此基础上将热、力、相变耦合关系引入热成形本构方程中, 分别建立了高强度钢板热成形的全量形式及增量形式本构方程. 对U形零部件热成形过程进行了数值模拟, 并与实验结果进行比较, 结果证明建立的本构理论的有效性.      

片状hBN的制备及摩擦性能研究

以CaB2O4作为烧结助剂,采用热压烧结技术制备了片状hBN.通过SEM、XRD和摩擦磨损试验机对hBN块体的显微结构、物相组成和摩擦性能进行了表征.结果表明:在N2气气氛下,烧结温度为2000℃,保温时间为5h时,CaB2O4的加入可以有效的提高hBN的结晶性能.烧结hBN呈片状结构,其粒径约为0.5～2 μm,厚度约为200nm.hBN块体的摩擦系数和磨损量均随着温度的升高先增大后稍有降低,在600℃时,摩擦系数和磨损量均达到最高,其空气和水蒸气气氛下的摩擦系数分别为0.6和0.25,磨损量分别为9.1 mg和4.9 mg.在整个测试温度范围内,水蒸气气氛下的摩擦系数和磨损量均比空气气氛下低,这主要是因为:室温下,水蒸汽在hBN与摩擦副的摩擦表面形成一层水膜;高温下,hBN可以与水蒸汽发生反应,生成H3BO3.     

MgO-CeO2烧结助剂对高SiC含量SiC基复相陶瓷致密性与导热性能的影响

以MgO-CeO2为烧结助剂,采用热压烧结工艺在1850C制备了SiC含量为80wt;的SiC-AlN复相陶瓷.研究了不同助剂含量对复相陶瓷致密性与导热性能的影响.结果表明:适量的烧结助剂能够对SiC-AlN复相陶瓷起到促进烧结作用.烧结助剂含量为6wt;时,样品显气孔率偏大;当助剂含量提高至8wt;～14wt;时,样品显气孔率显著降低,能够完全烧结致密化.复相陶瓷在烧结助剂含量为1Owt;时获得最佳的致密性,其显气孔率仅为0.14;.在烧结助剂含量为8wt;时,样品具有最高的热导率51.72 W·m-1·K-1.复相陶瓷的热导率主要受样品致密性和晶界相的影响,不足或过量的烧结助剂都会使样品的热导率降低.     

热注入法合成PbX(X=S,Se)量子点的结构和性能研究

采用热注入的方法在空气氛围中合成PbX(X=S,Se)量子点,液体石蜡和磷酸三丁酯(TBP)作为不同的溶剂优化PbSe量子点的合成;使用六甲基二硅硫烷(TMS)作为硫源合成了第一激子吸收峰在900 ～ 1500 nm分布的PbS量子点.通过透射电镜(TEM)、X射线衍射(XRD)和吸收光谱等测试手段对合成的物质进行成分与光学性能分析表征,对比研究了Ⅳ-Ⅵ族化合物量子点在成核过程中的差异.结果表明在相同的实验条件下PbS量子点的反应条件相对温和,量子限域效应明显;而PbSe量子点的合成对环境的要求更加严苛,反应温度更高,量子点的尺寸分布更宽.     

Hot corrosion behavior of the spray-formed nickel-based superalloy

An investigation of low temperature hot corrosion is carried out on a spray-formed nickel-based superalloy FGH100pre-coated with Na_2SO_4~- NaCl at 700℃ for 100 h. Mass gain measurement, x-ray diffraction, scanning electron microscopy, and energy dispersive x-ray spectroscopy are used to study the corrosion behavior. Results reveal that corrosion behavior follows a sequence, that is, first rapidly proceeding, then gradually slowing down, and finally forming an outer layer composed of different types of oxides and an inner layer mainly comprised of sulfides. In-depth analysis reveals that the hot corrosion of FGH100 is a combined effect of oxidation-sulfidation and transfer of oxides.     

EAST 装置等离子体逃逸电子同步辐射行为的实验研究

通过红外可见内窥镜诊断系统对EAST 等离子体芯部逃逸电子的同步辐射功率谱进行了分析,得出低能段逃逸电子同步辐射主要在红外波段,随着逃逸电子能量的增加,同步辐射向短波方向移动进入可见光波段。在欧姆放电条件下,对逃逸电子同步辐射所产生的的红外可见光进行了成像分析,同时研究了EAST 等离子体在低杂波和中性束注入加热条件下的逃逸电子行为。实验结果显示,低杂波和NBI 的投入总体抑制电子的逃逸,但低杂波投入初期产生的快电子对逃逸电子的产生具有促进作用。