High purity gadolinium by the electrolysis of GdF3

The anodic overvoltage on carbon and platinum electrodes in the electrochemical production of high purity gadolinium from molten 75 LiF-25 mol% GdF₃ solutions is discussed. At the cell temperature of 840°C calciumimpregnated anodes led to the reduction of inert electrode films and to a current yield of nearly 100%.The deposited gadolinium contained 75, 22, 54 and less than 100 ppm of the interstitial elements H, N, O and C respectively; the concentrations of the highest other analysed impurities were: Si (89), Fe (15), Y (5), Zr (3), Nd (3), Tb (71), Ta (49), W (23) and Re (<3 ppm).Partly performed at the Ames Laboratory—U.S. Department of Energy.     

单分散交联聚甲基丙烯酸环氧丙酯树脂的制备及亲合纯化伴刀豆球蛋白-A

采用一步种子溶胀聚合法制备了颗粒呈单分散的交联聚甲基丙烯酸环氧丙南树脂，对其环氧基的组成比进行了表征，并以氨基葡萄糖为配基，首次制备了纯化粗品伴刀豆球蛋白-A(Ⅲ）(Con-A，Ⅲ)的聚合物基质的高效亲合色谱柱。配基在树脂上的键合量为8．2mg／g，对纯化后的Con-A（Ⅲ）的吸附量为13．4mg／g。使用该亲合色谱介质成功地从粗品Con-A中快速纯化了Con-A，电泳分析显示为一个主要的谱带，纯度从15％提高到95％。     

Electrochemical instability of bis(trifluoromethylsulfonyl)imide based ionic liquids as solvents in high voltage electrolytes for potassium ion batteries

1. Download : Download high-res image (153KB)
2. Download : Download full-size image

     

氰氟草酯及其代谢物在稻田水、土壤和稻株中的残留分析方法

研究并建立了氰氟草酯及其 4种代谢物在稻田水、土壤及稻株中的残留分析方法。在同一色谱分析条件下 ,同时检测 5种化合物 ,样品前处理过程简单 ,方法准确可靠 ,灵敏度和准确度达到了农药残留检测的要求。氰氟草酯及 4种代谢物在上述样品中的最低检知浓度在 0 .0 2～ 0 .0 0 4mg kg之间 ,方法的添加回收率(0 .0 1～ 5mg kg)在 80 .2 %～ 1 0 1 .2 %之间     

Microwave and RF surface wave sustained discharges as plasma sources for plasma chemistry and plasma processing

The surface wave produced plasma belongs to a class of RF and microwave induced plasmas. It results from the propagation of an electromagnetic wave which uses the plasma column it sustains and the plasma tube as its sole propagating media. This type of plasma offers several advantages compared to the positive column plasma of dc discharges or to other RF and microwave produced plasmas. Surface wave plasmas require no internal electrodes, and they can be applied over an extremely broad range of wave frequencies (27 MHz to 10 GHz demonstrated) and gas pressures (about 10^–4 Torr to a few times the atmospheric pressures). Using the surface wave plasma technique, a large variety of plasma column diameters have been created (0.5–150 mm demonstrated) and no limitation on plasma column length (column up to 6 m long demonstrated) has been found. The surface wave produced plasma is used in elemental analysis and to sustain emission in lasing media. This article is intended as a guide for potential users of surface wave plasmas in the field of plasma processing and plasma chemistry.     

Synthesis and properties of new crystalline poly(arylene ether nitriles)

Crystalline poly(arylene ether nitrile) could be prepared by the polycondensation of 2,6-dihalobenzonitrile with resorcinol at 200°C in N-methylpyrrolidone in the presence of sodium carbonate. A reaction temperature of at least 200°C was necessary to attain high molecular weight polymer. Spectral data indicated that the polymer had the structure of a poly(meta-phenylene ether) with pendent nitrile groups on every other phenylene unit. Despite this structure, the crystallinity and the crystallization rate of the polymer were greater than those of the corresponding polymer with a para-linked structure. The glass transition temperature and the melting temperature of the polymer were almost the same as those of poly(etheretherketone) (PEEK^TM). A series of other new poly(arylene ether nitriles) were also examined. The polymers derived from 4,4′-biphenol, dihydroxytetra-phenylmethane, dihydroxydiphenylsulfone, and 1,5-isoquinolinediol had high glass transition temperatures. The poly(arylene ether nitriles) exhibited excellent tensile strength compared with the corresponding ketone- or sulfone-containing polymers. Comparing the three different kinds of polymers containing the same bisphenol units, the order of glass transition temperature was found to be sulfone- > nitrile- > ketone-containing polymers, while the order of tensile strength was nitrile- > ketone- > sulfone-containing polymers. The excellent mechanical properties are attributable to dipole-dipole interactions of nitrile groups. © 1993 John Wiley & Sons, Inc.     

SYNTHESIS, CHARACTERIZATION, METAL-UPTAKE BEHAVIOR OF BIS（BENZIMIDAZOLE） RESIN SUPPORTED ON EPOXIDE POLYMER

The new chelate resins, abbreviated as PNBMZs and PBBMZs based on epoxide polymer, were synthesized by polycondensation of N,N-diglycidyl-4-glycidyloxyaniline or 1,4-bis（2,3-epoxypropyl）benzene with the primary amine group of 1,3-bis（benzimidazol-2yl）propylamine （BBPAH）. The ion exchangers contain 2.71-3.23 mmol of the ligand contents per gram of the resin. Batch extraction capacities were determined for the metal chloride salts in buffer solutions in the pH range from -1 to 6.0. The chelate resins were very selective for Cu^2＋, Zn^2＋, Cd^2＋ in the presence of other divalent transition metal ions. The maximum uptake capacities of PNBMZ （synthetic molar ratio = 1：1.5） under non-competitive condition were found to be 0.94 mmol/g for Cu^2＋ at pH = 2, 1.3 mmol/g for Cd^2＋ at pH = 1 and 1.75 mmol/g for Zn^2＋ at pH = -1 respectively. While in the case of PBBMZ, it was 1.39 mmol/g for Cd〉 at pH = 1. The metal-uptake behaviors for both of them showed strong pH dependence, and their extraction capacities increase with decreasing pH. The uptake of Cu^2＋ by the resin PNBMZs at pH = 1 was found to be rather fast with t1/2 = 18 min. Metal-uptake experiments under competitive conditions also confirm that the chelate resins have a high selectivity for Cu^2＋, Zn^2＋, Cd^2＋ and the contrary pH dependence.     

INTROMISSION OF WATER-REPELLENT AND HYDROSCOPIC PROPERTIES SIMULTANEOUSLY TO PP BY PLASMA DISCHARGE METHOD

Plasma-induced surface graft copolymerization of acrylic acid on polypropylene non-woven fabric (PP-g-AA) and polypropylene membrane were reported. The extents of grafting were controlled by the plasma and polymerization condition. Hexadecyltrimethyl ammonium bromide was then coupled with the carboxyl group of PP-g-AA to obtain a polyion complex (PIC). At last, CF4 plasma was used to give PICs hydrophobic property. The moisture regain and water-repellency of the processed PICs was investigated. The surfaces were characterized using ATR FT-IR and XPS. The result indicates that the products have very high ability to adsorb moisture, even better than cotton fiber. At the same time, the products show excellent hydrophobic property, which can‘t be wetted by those reagents whose surface tensions were higher than 327mN/m.     

Apparent molar volumes of aqueous calcium chloride to 250°C, 400 bars,and from molalities of 0.242 to 6.150

Relative densities of CaCl ₂ (aq) with 0.22ml(mol-kg^–1)6.150 were measured with vibrating- tube densimeters between 25 and 250°C and near 70 and 400 bars. Apparent molar volumes V calculated from the measured density differences were represented with the Pitzer ioninteraction treatment, with appropriate expressions chosen for the temperature and pressure dependence of the virial coefficients of the model. It was found that the partial molar volume at infinite dilution V ^o , and the second and third virial coefficients B ^V and C ^V , were necessary to represent V near the estimated experimental uncertainty. The ionic-strength dependent ^(1)v term in the B ^V coefficient was included in the fit. The representation for V has been integrated with respect to pressure to establish the pressure dependence of excess free energies over the temperature range studied. The volumetric data indicate that the logarithm of the mean ionic activity coefficient, ln ±(CaCl ₂ ), increases by a maximum of 0.3 at 400 bars, 250°C, and 6 mol-kg^–1 as compared with its value at saturation pressure.     

Towards advanced circuit board materials: adhesion of copper foil to ultra‐high molecular weight polyethylene composite

Polyethylene based composites are attractive materials for advanced circuit board applications because of their unique combination of properties: low dielectric constant and loss factor, light weight, high flexural modulus and low thermal expansion coefficient controlled in all spatial directions. This investigation describes a process to consolidate chopped fibers of ultra‐high molecular weight polyethylene concurrently with its bonding to a copper foil. Bonding is affected by a thin sheet of low‐density polyethylene, incorporating a crosslinking agent with a concentration gradient across the sheets thickness. In this single step process, the composite material is formed and bonded to the metal foil, achieving good adhesion without the use of extraneous glue. Copyright © 2002 John Wiley & Sons, Ltd.