Coprecipitation with metal hydroxides for the determination of beryllium in seawater by graphite furnace atomic absorption spectrometry

Coprecipitation first with magnesium hydroxide, next with tin(IV) hydroxide is developed for the determination of traces of beryllium in sea-water. To a 200-ml sample is added a sodium hydroxide solution to form magnesium hydroxide at pH 11.5, on which beryllium is quantitatively coprecipitated. The precipitate is separated by centrifugation and dissolved in 2 ml of 12 mol/l hydrochloric acid. The resulting solution (ca. 10 ml) is mixed with 2 mg of tin (IV) carrier and the pH is adjusted to 5.0 to collect the beryllium on tin (IV) hydroxide, leaving magnesium ions in the solution. The tin (IV) hydroxide is centrifuged, dissolved in 0.1 ml of 5 mol/l hydrobromic acid, and then diluted to 1 ml with water. Magnesium is so added as to be 500 g/ml for increasing the sensitivity about four times, and the beryllium in the solution is determined by graphite furnace atomic absorption spectrometry. The experiments with synthetic seawater samples showed that pg — g amounts of beryllium can be coprecipitated on the metal hydroxides and beryllium at the low ng/1 level can be determined with reasonable precision (RSD < 10%). The detection limit of the proposed method is 0.5 ng/l of beryllium in seawater.     

Corrugated single-layer graphite sheet as a model of stepped surface of a crystal

Electronic structure calculations have been performed for flat graphite sheets and periodically distorted sheets with different values of deformation angle and hydrogen adsorption. These characteristics do not all behave monotonically with increasing deformation angle. At small deformation angles, the electrons pass from the atoms of terraces to those of edges, while at larger angles the reverse pattern is observed. The position of the Fermi level also varies nonmonotonically. The binding energy of hydrogen depends significantly on the adsorption site, and the difference can be doubled. Based on the ata obtained, it was concluded that a priori statements derived from the “general concepts” on the difference in the physicochemical properties of, for example, terrace and edge atoms on high-index facets are unreliable.     

石墨炉原子吸收法中热解涂层石墨管在无标准分析法测定环境样品中铬的应用

本文探讨了热解涂层石墨管测定铬的最佳实验条件,研究了各种酸和干扰物质的基体效应,提出用浓氨水为基体改进剂克服高氯酸的干扰。比较了各原子化温度时的理论和实验特征量。使热解涂层石墨管有可能用于无标准分析法测定各种环境样品中的铬。     

石墨炉原子吸收法测定钒的研究

本文比较了在标准石墨管,热解涂层和全热解石墨管中钒的吸收信号形状。用全热解石墨管和EDTA铵盐作基体改进剂,直接测定水系沉积物中痕量钒。方法的特征量为61pg/0.0044A。     

Nafion化学修饰圆盘预富集-石墨炉 原子吸收联用法对牛血超氧化物歧化酶中铜、锌分布状态的研究

本文研究了Nafion化学修饰钨丝圆盘预富集-石墨炉原子吸收(GFAAS)方法测定牛血超氧化物歧化酶(SOD)中游离态Cu～(2+)及Zn～(2+)的方法,并用GFAAS法直接测定SOD中铜、锌的总量,证实了牛血SOD中金属辅基铜、锌原子个数比为1:1,初步探讨了一定浓度的牛血SOD中Cu～(2+)、Zn～(2+)的表观离解平衡常数。为提高SOD的活性和稳定性的研究,提供了一种有效的方法。     

原子吸收光谱法测定拉伸断口铬镍钼钛钢样品中主成分

研究了毫克级铬镍钼风样品中主成分镍的火焰原子吸收光谱法（FAAS法）和铬、钼、钒、钛、铝的塞曼恒温平台石墨炉原子吸收光谱法（ZSTPF－AAS法）。采用了微波溶样技术作为防污染样品预处理技术，采用石墨管硅涂层改进技术提高了仪器的测试精度。其中铬、镍、钼、钒、钛、铝的相对标准偏差分别为2.7%,0.97%,8.6%,7.3%,1.7%,7.3%。其加标回收率分别为96.5%,97%,96.7%,93%,98%,91%。通过分析，发现在较低温度下铬镍钼钛钢断面上有轻微的钼偏析现象，可能是拉伸断裂的主要化学影响因素。     

石墨炉原子吸收法测定生物样品中镉的几种基体改进剂的比较

本文比较了磷酸二氢铵、氟化铵、硫酸铵、氯化钯、氯铂酸以及氯铂酸与多种有机酸的混合试剂在测定ＧＢＷ猪肝标准物质中镉时基体改进效果，其中，氯铂酸的基体改进能力最强，猪肝标准物质的回收率在９０％     

蒙脱石-石墨-聚氯乙烯复合电极测定制药废水中苯酚

报道了当制药废水PH8．0时，用蒙脱石－石墨－聚氯乙烯复合电极可以直接测定苯酚的含量而不受水杨酸存在的干扰，苯酚浓度在1．0μg/mL-25.0μg/mL范围内峰电流与浓度有良好的线性关系，I＝1．262c-0.046，相关系数r=0.998，检出限为0．1μg/mL，用该方法测定模拟制药废水中苯酚，其平均回收率为101．7％。     

Surface film formation on a graphite electrode in Li‐ion batteries: AFM and XPS study

The formation of a passivation film (solid electrolyte interphase, SEI) at the surface of the negative electrode of full LiCoO₂/graphite lithium‐ion cells using LiPF₆ (1M ) in carbonate solvents as electrolyte was investigated by means of x‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The analyses were carried out at different potentials of the first and the fifth cycles, showing the potential‐dependent character of the surface‐film species formation. These species were mainly identified as Li₂CO₃ up to 3.8 V and LiF up to 4.2 V. This study shows the formation of the SEI during charging and its partial dissolution during discharge. Copyright © 2005 John Wiley & Sons, Ltd.     

Cyclic Voltammograms of Ferrocene on Multi‐Walled Carbon Nanotubes (MWCNTs)‐Modified Edge Plane Pyrolytic Graphite (EPPG) Electrode in Room Temperature Ionic Liquids (RTILs) of 1‐Ethyl‐3‐Methylimidazolium Tetrafluoroborate (EMIBF4)

In this work, the electrochemical behavior of ferrocene (Fc) was investigated by cyclic voltammetry (CV) in room temperature ionic liquids (RTILs) of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIBF₄) on glass carbon (GC), edge plane pyrolytic graphite (EPPG) and multi‐walled carbon nanotube (MWCNTs)‐modified EPPG electrodes, respectively. The results demonstrated that on GC electrode, pairs of well‐defined reversible peaks were observed, while for the electrode of EPPG, the peak potential separation (ΔE_p) is obviously larger than the theoretical value of 59 mV, hinting that the electrode of EPPG is distinguished from the commonly used electrode, consistent with the previous proposition that EPPG has many “defects”. To obtain an improved electrochemical response, multi‐walled carbon nanotubes (MWCNTs) were modified on the electrode of EPPG; the increased peak current and promoted peak potential separation not only proved the existence of “defects” in MWCNTs, but also supported that “creating active points” on an electrode is the main contribution of MWCNTs. Initiating the electrochemical research of Fc on the MWCNTs‐modified EPPG electrode in RTILs and verifying the presence of “defects” on both EPPG and MWCNTs using cyclic voltammograms (CVs) of Fc obtained in RTILs of EMIBF₄, is the main contribution of this preliminary work.