Perturbed angular correlation study of radiation-induced defects in Rh metal

Radiation-induced defects are studied in cubic rhodium metal, using the local probe technique ‘Time differential perturbed angular correlation’ (TDPAC) at liquid N₂ temperature. Isochronal annealing was done at 300, 1073 and 1473 K temperatures. The irradiated sample showed two quadrupole interaction frequencies at 1150 and 93 MHz. The low frequency disappeared at room-temperature annealing, which was assigned to In trapped at a vacancy, whereas the higher frequency remained up to high temperatures and was attributed to In trapped at Rh–C complexes in the Rh matrix.     

Determination of Lead in Human Hair by High Resolution Continuum Source Graphite Furnace Atomic Absorption Spectrometry with Microwave Digestion and Solid Sampling

The content of lead in human hair was measured by high resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GFAAS) combined with microwave-assisted digestion (MAD) and direct solid sampling (DSS). Hair strands were washed, dried, and then cut into three parts (root, middle portion, and tip). For MAD-GFAAS assays, approximately 0.25 g of hair was completely digested using a mixture of concentrated nitric acid and hydrogen peroxide in a closed system. In the DSS-GFAAS assays, 0.1–0.2 mg of dried hair was directly introduced into a graphite furnace using a solid autosampler. The temperature programs were optimized and the effects of various added modifiers were compared. The results indicated that NH₄H₂PO₄ was the optimal modifier for analysis of Pb using GFAAS. Use of the optimal modifier and temperature program gave similar limits of detection for MAD-GFAAS and DSS-GFAAS of 1.16 ng/g and 0.82 ng/g, respectively. Both methods also produced satisfactory recoveries ranging from 98.69% to 103.14%. There was no significant difference observed between the Pb contents of hair strands determined by the MAD-GFAAS and DSS-GFAAS assays, which both indicated that the Pb levels increased along the hair strands. Comparison of the two methods revealed that DSS-GFAAS had several advantageous characteristics over MAD-GFAAS, including the need for much less sample material and having a less time-consuming procedure, lower sample blank absorbance, lower memory effect, and no risk of environmental pollution by digesting chemicals. The direct solid sampling technique can be employed as a good alternative to conventional wet digestion in AAS assays.     

光伏电站设计智能优化

由于目前光伏电站设计目前没有相应的标准,因此以个人经验为指导的情况,无法保证电站建设的成本最优,鉴于此问题,本文提出了一种光伏电站优化设计方法,基于模拟退火算法,通过对光伏区域中的组件进行最优分组来实现两级电缆成本的最优。并通过实际项目对该算法进行检验,达到比较理想效果。     

NiuPt1-uSivGe1-v/Si0.72Ge0.28界面形貌的改善

针对锗硅在形成金属锗硅化物时存在部分应力释放、界面形貌特性变差的问题,提出了在Si0.72Ge0.28上分别外延薄硅(Si)覆盖层和锗硅(Si072Ge0.28)缓冲层的工艺方案.实验结果表明,通过两步快速热退火,两个方案的工艺条件都能形成低阻的NiuPt1-uSitGe1-v和改善NivPt1-uSitGe./Si0.72Ge0.28的界面形貌.但相比较而言,在Si0.72Ge0.28上外延10 nm Si覆盖层的方案能够形成更好的NiuPt1-uSivGe1-t/Si0.72Ge0.28界面形貌.与没有改进的方案相比,该方案形成的肖特基接触更具有更低的肖特基接触势垒高度,更易形成欧姆接触.     

太阳能建筑物外观及表面光伏组件铺设优化

针对太阳能建筑物外观图的设计及外表面太阳能光伏组件铺设优化问题,首先通过建立以建筑物5个外表面全年总辐射量最大为目标的单目标规划模型,并考虑建筑物的设计要求,基于模拟退火法给出了建筑物的外观设计图,并根据电池性能的优劣顺序及限制条件,利用贪心算法得到建筑物外表电池铺设方案,最后给出了这种方案下的投资收回年限及寿命期内的经济效益。     

高速传输系统用低损耗单模光纤的研究

介绍了国际上低损耗单模光纤的研究进展,从理论上分析了低损耗单模光纤实现的技术途径。通过对石英玻璃物理特性的研究,探索出石英玻璃光纤的退火工艺,以降低光纤的内应力从而降低光纤的衰减。采用自主知识产权的专利技术制造的光纤在1 310、1 550和1 625nm波长的衰减典型值分别为0.320、0.182和0.195dB/km。该光纤的技术指标优于ITU-T国际标准和GB/T规定的光纤指标值。     

Improved Photobleaching for (1,10-phenanthroline)tris[4,4,4-trifluoro-1-(2-thienyl)-1,3-butanedionato]europium(III) Particle Embedded in Sol-Gel Derived Glass Film

In this research, we investigated improved photobleaching characteristics of (1,10-phenanthroline)tris[4,4,4-trifluoro-1-(2-thienyl)-1,3-butanedionato]europium(III) by forming nano-particles embedded into a sol-gel derived silica glass film by a conventional sol-gel process. The relative photoluminescence intensities after the UV irradiation for 90 min were 88, 76, and 67% for nano-particles in the sol-gel derived glass film, powders in the sol-gel derived glass film, and raw powders, respectively. This result indicates that the phtobleaching of this Eu-complex can improved by forming nano-partcile structures by a reprecipitation method and embedding in the sol-gel derived silica glass.     

低温共烧陶瓷用硼硅酸盐玻璃的研究进展

概述了低温共烧玻璃陶瓷复合材料体系中所采用的硼硅酸盐玻璃的组成、工艺、应用技术参数。比较了锌、铅、钡硼硅酸盐玻璃组成、掺杂量对玻璃陶瓷的烧结特性的影响。指出了不同硼硅酸盐玻璃材料的优缺点和在低温共烧陶瓷技术中的适用范围。     

Hermetic Seal of Organic Light Emitting Diode with Glass Frit

The components of OLED encapsulation with hermetic sealing and a 1026-day lifetime were measured by PXI-1033. The optimal characteristics were obtained when the thickness of the TPBi layer was 20 nm. This OLED obtained a maximum luminance (Lmax) of 25,849 cd/m² at a current density of 1242 mA/cm², an external quantum efficiency (EQE) of 2.28%, a current efficiency (CE) of 7.20 cd/A, and a power efficiency (PE) of 5.28 lm/W. The efficiency was enhanced by Lmax 17.2%/EQE 0.89%/CE 42.1%/PE 41.9%. The CIE coordinates of 0.32, 0.54 were all green OLED elements with wavelengths of 532 nm. The shear strain and leakage test gave results of 16 kgf and 8.92 × 10⁻⁹ mbar/s, respectively. The reliability test showed that the standard of MIL-STD-883 was obtained.     

改进的PCVD工艺制造高掺硼材料的性能研究

介绍了一种用于制造光纤的高掺硼石英材料的性能.简单回顾基本的工艺条件和关键工艺参数之后,主要讨论材料性能,如玻璃结构、折射率、粘度、热膨胀系数和残余应力等.另外还介绍了两种高掺硼光棒的性能.