LD泵浦的Nd∶YAG腔内倍频激光器及其模式

用KTP晶体研制成LD泵浦的YAG腔内倍频激光器,得到0.532μm连续绿色线偏振激光输出,阈值泵浦功率为41mW,输出功率为1.4mW,斜效率为1.7％。研究了泵浦光对倍频激光横模的影响。     

Solid Ink Laser Patterning for High-Resolution Information Labels with Supervised Learning Readout

Tagging, tracking, or validation of products are often facilitated by inkjet-printed optical information labels. However, this requires thorough substrate pretreatment, ink optimization, and often lacks in printing precision/resolution. Herein, a printing method based on laser-driven deposition of solid polymer ink that allows for printing on various substrates without pretreatment is demonstrated. Since the deposition process has a precision of <1 µm, it can introduce the concept of sub-positions with overlapping spots. This enables high-resolution fluorescent labels with comparable spot-to-spot distance of down to 15 µm (444,444 spots cm⁻²) and rapid machine learning-supported readout based on low-resolution fluorescence imaging. Furthermore, the defined thickness of the printed polymer ink spots can be used to fabricate multi-channel information labels. Additional information can be stored in different fluorescence channels or in a hidden topography channel of the label that is independent of the fluorescence.     

New FIR laser lines and frequency measurements in CD3OD

Twenty-four new submillimeter laser lines in fully deuterated methyl alcohol (CD₃OD) in the wavelength range from 52 to 328 m have been obtained in a Fabry-Perot FIR resonator by optically pumping the methanol with a cw CO₂ laser. We have made accurate wavelength measurements and have determined the relative polarization of most of the known CD₃OD laser lines. The frequencies of 13 of the strongest lines were also measured.Contribution of the U.S. Government, not subject to copyright.     

Mixed Polymer‐Coated Magnetic Nanoparticles as Forward Osmosis Draw Agents of Tuned Hydrophilicity

We recently reported a polymer‐coated magnetic nanoparticle (MNP) draw agent for the forward osmosis (FO) water desalination process. The water flux was found to increase when the polymer poly(sodium acrylate) (PSA) was anchored to the MNP surface as compared to the polymer (or polyelectrolyte solution) alone, due to the polymer chains being stretched out and most of the hydrophilic groups on the polymer contributing to water flux. We herein report the use of a secondary polymer poly(N‐isopropylacrylamide) PNIPAM to manipulate the PSA polymer conformation and influence inter‐ and intrachain interactions to enhance the efficiency of the FO draw agent. These PSA–PNIPAM‐coated MNPs generated a much higher water flux of ～11.66 LMH when compared to the 100 % PSA‐coated MNPs featuring a value of ～5.32 LMH under identical FO conditions. The osmotic pressure and water flux driven by the mixed polymer‐coated MNPs were found to be a strong function of the net polymer coverage on MNPs, that is, net available hydrophilic groups. Our new draw agent demonstrates potential for use in the water industry due to its improved efficiency and cost effectiveness as it uses only ～0.062 % (w/v) of the draw agent solution.     

Performance analysis of multi‐antenna relay communication systems with MRC

The performance of multi‐antenna relay communication systems is investigated in this letter. The source broadcasts the signal to all the relays and the destination. Decode‐and‐forward scheme is adopted at the relays, and the destination employs maximum ratio combining (MRC) technique to maximize the received signal‐to‐noise ratio. Closed‐form expressions of outage probability are derived in the MRC case and minimum routes MRC case. An adaptive grouping algorithm of relay antennas is also presented under the constraint of total antenna number. Simulation results show that the analytical curves agree with the simulated ones very well, and the performance of the proposed grouping algorithm is very close to the upper bound mentioned in other papers. Copyright © 2012 John Wiley & Sons, Ltd.     

缓冲气体及温度对DPAL输出性能的影响

为进一步提高半导体激光泵浦碱金属蒸汽激光器输出功率,基于三能级速率方程的理论模型,对DPAL的运行进行了模拟,考虑泵浦光带宽,在纵向泵浦的情况下,对缓冲气体气压、增益池长度、温度等参量对激光器输出光强及光光效率的影响进行了计算机模拟,结果表明,一定泵浦光下光光效率随着乙烷气压和温度增加而增大,对一定氦气气压有最大值,模拟结果为实验研究提供了有益的参考。     

AlGaN中Mg掺杂对蓝光发光二极管光电性质的影响

采用金属有机化学气相沉积技术生长了GaN基多量子阱(MQW)蓝光发光二极管外延片,并采用高分辨率X射线衍射仪(HRXRD)和光致光谱仪(PL)表征晶体质量和光学性能,其他的光电性能由制成芯片后测试获得,目的是研究外延片p型AlGaN电子阻挡层Mg掺杂的优化条件.结果表明,在生长p型AlGaN电子阻挡层的Cp2Mg流量为300 cm3/min时,蓝光发光二极管获得最小正向电压VF,而且在此掺杂流量下的多量子阱蓝光发光二极管芯片发光强度明显高于其他流量的样品.因此可以通过优化AlGaN电子阻挡层的掺杂浓度,来显著提高多量子阱蓝光发光二极管的电学性能和光学性能.     

同向抽运光纤拉曼放大器功率转换效率的理论分析

为了对同向抽运光纤拉曼放大器的功率转换效率进行研究,由耦合方程出发,首先理论推导出功率转换效率的解析解,然后采用数值计算的方法详细分析不同物理因素对功率转换效率的影响。结果表明：功率转换效率先随着光纤长度和单位面积的拉曼增益系数增加而增加,当增加到最大值时保持数值不变;小信号时,初始信号光功率对功率转换效率的影响较小;大信号时,功率转换效率随着初始信号光功率增加而快速增加;功率转换效率和初始抽运光功率呈抛物线曲线关系;抽运光与信号光的频率比增加时,功率转换效率减小。     

基于PI迟滞模型的压电陶瓷复合控制算法研究

为减小压电陶瓷的迟滞非线性对系统跟踪精度的影响,该文采用经典的存在逆解析的PI迟滞模型对压电陶瓷的迟滞特性进行建模,将PI模型的逆模型用于压电陶瓷的前馈控制算法中,然后设计了神经元比例、积分、微分(PID)反馈控制算法,将前馈控制算法与神经元PID反馈控制算法结合得到了压电陶瓷的复合控制算法。将仅含前馈的控制算法和复合控制算法在压电陶瓷的控制器上执行,实验结果表明,仅含前馈的控制算法的跟踪误差为1.256μm,而复合控制算法的跟踪误差仅为0.092μm,该复合控制算法使跟踪精度提高了1.164μm。     

准谐振正激变换器零电压开关设计

准谐振有源箝位正激变换器的有源箝位电路与常规的有源箝位正激变换器的结构类似,但实际工作过程存在许多差异。通过分析准谐振有源箝位正激变换器的工作过程,研究了准谐振有源箝位正激变换器的开关管零电压导通的边界条件,并进行了仿真和实验验证。