日本α－Al_2O_3粉体进展

综述了日本近１０多年来α－Ａｌ２Ｏ３粉体的发展状况。特别介绍了日本对α－Ａｌ２Ｏ３粉体的标准化工作。这对提高电子陶瓷等产品的质量是非常重要的。     

Preparation of ultra fine nickel-copper bimetallic powder for BME-MLCC

The preparation of ultra fine nickel-copper bimetallic powder with two-stage chemical reduction method was investigated. Reductive sugar and hydrazine hydrate were employed as reducing agent in different reductive stage, respectively. Reaction of CuSO₄·5H₂O with reductive sugar at 70 °C gives cuprous oxide and copper particles, then as-prepared mixture and nickelous hydroxide were reduced by hydrazine hydrate, and nickel-copper powder having excellent dispersibility was prepared. Influences of nickel added on composition and dispersibility of powder were studied. TG/DTG/DTA of nickel-copper powder, which is stable in room temperature, were discussed with thermal analyzer. Relation of nickel content to oxidation temperature was investigated. Ni-Cu bimetallic powder particles have a fully coated structure when nickel content is up to 30%. As-prepared nickel-copper powder was applied in base metal electrode-multilayer ceramic capacitor (BME-MLCC). The end termination has high adhesion force, fairly good densification, low resistivity, excellent solderibility behavior and resistance behavior to soldering.     

TiO2 粉末催化剂光催化降解室内 空气中有机污染物

本文制备了一系列 TiO2粉末催化剂, 用光催化法降解室内空气中各种微量有机污染物,最终降解率 接近 100%. 考察了晶型对光催化剂性能的影响, 结果表明,锐钛矿型 TiO2 的催化性能最好. 最后,分析了 TiO2 光催化反应机理.     

XPS对离子交换法光色玻璃中银的状态研究

本文介绍利用ｘ射线光电子能谱分析仪（ＸＰＳ），对玻璃表面银的存在状态进行研究，实验结果表明银以Ａｇ＾０、Ａｇ＾＋、Ａｇ＾＋＋三种状态存在，而Ａｇ＾＋的存在有利于玻璃光色性的提高。文中并提出了在工艺过程中应采用惰性或弱氧化性气氛。     

激光焊接超细基胎体金刚石薄壁钻

采用激光焊接超细预合金粉胎体，开发了新的薄壁钻产品，通过对与现有的产品工艺、性能测试以及实际使用分析对比，结果表明：激光焊接与普通钎焊相比结合强度提高2－3倍，克服了胎体脱落问题，胎体耐磨性提高了50％－120％，其中轴向磨损速率提高1．2倍；钻削速度提高30．4％，工矿适应性增加，使用寿命提高25％－108％。     

Rebuilding of metal components with laser cladding forming

Laser cladding forming (LCF) is a novel powerful tool for the repairing of metal components. Rebuilding of V-grooves on medium carbon steel substrates has been carried out with laser cladding forming technique using stainless steel powder as the cladding material. Microstructure of the deposited layers has been characterized using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray microanalysis (EDAX), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Mechanical properties of the rebuilt V-groove samples have been evaluated by tensile and impacting tests and microhardness measurement. Experimental results show that good fusion bonding between the rebuilt layers and the substrate has been formed, and the microstructure of the cladding layers is mainly composed of fine, dense and defect-free epitaxial columnar dendrites. Due to the effect of grain size refinement, the tensile strength, impacting toughness, elongation and microhardness of the rebuilt samples have been greatly enhanced compared to those of the substrate. Microhardness is also very uniform throughout the rebuilt regions. With the growth of the deposited layers, the microhardness increases gradually. The good ductility of the deposited regions is verified by the SEM fracture analysis.     

沉淀法制备CeO2超微粉末

采用过氧化氢－－氨水沉淀法在较低温度下制备ＣｅＯ２超微粉末。试验表明，溶液起始浓度及焙烧温度以形成粉素晶体粒径有一定影响。焙烧温度在２２０－８５０℃，所得ＣｅＯ２微粉均为立方晶系，透射电测试表明，粒子基本呈球形，晶体平均粒径随焙烧温度升高而增大。控制适当条件，可制得粒径范围在５－１３ｎｍ，比表面积１１１．８ｍ＾２／ｇ的ＣｅＯ２超微粉末。     

超高真空中银表面垂直谐波电流的实验测量

在超高真空的条件下,测量了清洁、自由银表面产生的光学二次谐波随基波电矢量与入射面之间夹角(?)的变化,从而通过理论公式,求得由Rudnick和Stern引入的,用于衡量垂直面电流密度的唯象参数a的值,在入射基频光波长为1.064μm时,被测定为-4.0±0.8.