光纤传感振动检测系统及其实验研究

实际工程结构中的振动检测是十分重要的，也是十分复杂的，常用的结构振动检测传感器易受工程现场恶劣环境的影响．而光纤传感器具有小巧、抗电磁干扰、灵敏度高、适合长期监测等优点。本文建立了基于马赫—曾德(Mech-Zehnder)干涉原理的光纤传感振动检测系统．研制了运用先进的数字信号处理技术采集和处理数据的专用软件，并在典型结构件——钢制悬臂梁结构上进行了外加信号作用下的强迫振动检测和冲击载荷作用下的自由衰减振动检测，测量了该结构件的频率及振幅，其结果与同时进行的成熟的电测结果相近，说明光纤传感器用于结构件的振动测量是可靠的。本文为光纤传感器应用于实际工程的振动检测提供了新的技术装置，具有工程应用前景。     

Color Zone Map in Peripheral Vision at Various Illuminance Levels

We measured the entire region of mesopic and photopic vision to determine the color zone covering the visual field with unique red, yellow, green, and blue hue components. Eight kinds of test stimuli in the natural color system (NCS) color notation system were used. These stimuli were presented at horizontal and vertical meridians, and at meridians inclined at 45° angles. The illuminance level was set at six levels: 0.01 lx-1000 lx. The evaluation method measured chromatic, white, and black components as well as the hue component of the stimuli. Results show that the color zone of the retina extended further into the periphery with increasing illuminance; the response of opponent colors y-b was shown to be greater than that of the opponent colors r-g.     

Light Diffraction of Aligned Polymer Fibers Periodically Dispersed by Phase Separation of Liquid Crystal and Polymer

We have confirmed light diffraction of aligned polymer fibers obtained by a phase separation of an anisotropic-phase solution of liquid crystal and polymer. He—Ne laser light passing through the polymer fibers was scattered in the axis vertical to the fibers, and had two peaks of light intensity symmetrical to the center of the transmitting laser spot. The two peaks were found to be caused by light diffraction due to the periodic polymer-fiber dispersion because the peaks corresponded to values calculated by intervals between the fibers. The periodical fiber networks are considered to be formed by anisotropic spinodal decomposition. This effect can be used to measure the dispersion order of the polymer fibers. © 2004 The Optical Society of Japan     

Completely biodegradable composites of poly(propylene carbonate) and short,lignocellulose fiber Hildegardia populifolia

The composites of biodegradable poly(propylene carbonate) (PPC) reinforced with short Hildegardia populifolia natural fiber were prepared by melt mixing followed by compression molding. The mechanical properties, thermal properties, and morphologies of the composites were studied via static and dynamic mechanical measurements, thermogravimetric analysis, and scanning electron microscopy (SEM) techniques, respectively. Static tensile tests showed that the stiffness and tensile strength of the composites increased with an increasing fiber content. However, the elongation at break and the energy to break decreased dramatically with the addition of short fiber. The relationship between the experimental results and the compatibility or interaction between the PPC matrix and fiber was correlated. SEM observations indicated good interfacial contact between the short fiber and PPC matrix. Thermogravimetric analysis revealed that the introduction of short Hildegardia populifolia fiber led to a slightly improved thermooxidative stability of PPC. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 666–675, 2004     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

用楔形柱面光纤微透镜耦合的1.3μm SOA组件

运用激光模式耦合理论分析了半导体光放大器(SOA)与单模通信光纤的连接损耗,并设计制作了楔形柱面光纤微透镜用来实现两者的模斑匹配,有效地降低了器件的光耦合损耗.本文介绍了楔形柱面光纤微透镜耦合的1.3 μm半导体光放大器(SOA)组件及其制作方法.该组件的最大增益不小于14 dB,其偏振灵敏度小于1 dB,增益波动不大于0.5 dB.     

两段级联掺铒光纤放大器的优化研究

基于Giles模型,研究了980 nm和1480 nm泵浦的两段级联掺铒光纤放大器(EDFA)的设计,得出了掺铒光纤(EDF)的最佳长度和光隔离器的最佳位置随泵浦功率和信号功率的变化关系.比较980 nm和1480 nm泵浦的两段级联EDFA,可以发现,前者的最佳EDF长度短,而光隔离器最佳位置距EDFA输入端远.     

Nd~(3+):YAG激光的光纤传输

首先叙述了光纤传输Nd~(3+): YAG激光的优点,接着分析了不同光纤和其传输Nd~(3+): YAG激光的特点。然后通过对光纤传输系统各部分的分析与设计,结合实际,设计了光纤耦合机构。最后,对来自于工件反射光问题提出了解决方案。     

Integrated Smart Sensor Calibration

In many applications electronic sensors are used toimprove performance and reliability of measurement systems. Suchsensors should provide a correct transfer from the physical signalto be measured to the electrical output signal. One importantstep to achieve this, is to calibrate each sensor by applyingdifferent reference input signals and adjusting the sensor transferaccordingly. Besides expensive reference equipment the calibrationprocess takes much time and attention per individual sensor,which means a considerable increase in sensor production costs.By including at the sensor or sensor interface chip a programmablecalibration facility the calibration of such smart sensors caneasily be automated and can be executed for a batch of sensorsat a time, thus minimizing the calibration time and costs. Thispaper presents a calibration method and options for integrationin the smart sensor concept, in hardware as well as in software.An advantage of the proposed method is that it does not needa large matrix of calibration data, which needs to be storedin a look-up table or converted into a correction formula, butinstead it uses a step-by-step approach to correct the sensortransfer at each calibration measurement until the error is sufficientlysmall.     

Optical bistability in an all-optical fiber nonlinear fabry-perot resonator with linear absorption

An all-optical fiber nonlinear Fabry-Perot resonator is proposed. The steady-state model for describing this resonator is developed. The transmission and refection bistabilities are shown numerically. Our results show that the bistability in this system is similar to that in a normal nonlinear Fabry-Perot etalon, except that the characteristics of the bistability can be changed not only by the cavity length but also by the phase shifts of the fiber loop mirrors.