激光冲击处理提高铝合金性能的研究

研究了高功率密度激光冲击处理对Ｌｙ１２ＣＺ铝合金力学性能的影响，研究结果表明激光冲击处理可大幅度提高铝合金的疲劳寿命，疲劳寿命的提高是由于微观组织中位错密度的明显增加，使得材料表层的强度和硬度也明显增加所致。     

An accurate method to predict the stress concentration in composite laminates with a circular hole under tensile loading

The paper presents a theoretical-numerical hybrid method for determining the stresses distribution in composite laminates containing a circular hole and subjected to uniaxial tensile loading. The method is based upon an appropriate corrective function allowing a simple and rapid evaluation of stress distributions in a generic plate of finite width with a hole based on the theoretical stresses distribution in an infinite plate with the same hole geometry and material. In order to verify the accuracy of the method proposed, various numerical and experimental tests have been performed by considering different laminate lay-ups; in particular, the experimental results have shown that a combined use of the method proposed and the well-know point-stress criterion leads to reliable strength predictions for GFRP or CFRP laminates with a circular hole. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 43, No. 4, pp. 531–570, July–August, 2007.     

A procedure for measuring the flexibility of single wood-pulp fibres

A way of determining the flexibility of wood-pulp fibres is developed, which involves i) a precise measurement of the topology of single-fibres by using a confocal laser scanning microscope and ii) the measurement of the elastic modulus of the fibres by using a single-fibre fatigue cell. Reported in this paper are the initial results of tests carried out on black spruce fibres, which have been subjected to three different levels of mechanical refining energy, namely ∼1100, 2300, and 3500 kWh/t. It is found that the fibre flexibility rises significantly between the first and second energy levels, but it does not change to the same degree between the second and third ones. The described procedure of measuring the flexibility of fibres may be used to establish the appropriate refiner energy necessary for the production of a specific grade of paper. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 115–128, January–February, 2006.     

环形线电荷的电场分布

给出了圆环形线电荷电场分布的理论公式，并利用计算机计算出其具体分布规律。     

气密性碳涂覆光纤筛选强度与电阻关系研究

通过实验分析确立了把光纤电阻作为衡量气密性碳涂覆光纤通过２％应变筛选的过渡标准。要拉制２％应变筛选的碳涂覆光纤，其电阻值应小于３０ｋΩ／ｃｍ。     

双相位共轭镜的工作条件参数分析

本文讨论了纯扩散机制的光折变晶体用作单作用区的双相位共轭镜（ＤＰＣＭ）时的阈值耦合强度和允许的输入光强比范围，并与双作用区的情况进行比较后，给出了在输入光强比远离１的条件下，双相位共轭镜的正常工作的条件参数。     

稀土复合变质对新型铸造热锻模具钢组织与性能的影响

研究了稀土复合变质对新型铸造热锻模具钢（CHD钢）组织与性能的组织。结果表明，稀土复合变质能细化晶粒，并且随着稀土量的增加。细化效果明显；加入适量的稀土复合变质后，夹杂物数量明显减少，夹杂物趋于球化并均匀地分布在钢中，形态和分布得以了改善，向钢中加入稀土进行复合变质，能促进贝氏体、奥氏体和位错亚结构的形成，细化马氏体板条。当残留稀土含量为0.02%时，CHD钢的硬度、强度变化不大，断裂韧性（KIC）和疲劳裂纹扩展门槛值（△Kth）有所提高，冲击韧性、延伸率、断面收缩率提高了近一倍，抗热疲劳性能也最好。     

Mg-Nd-Zr-Zn合金的制备及钕对合金组织性能的影响

在RJ-2溶剂和Be的联合保护下制备了Mg-Nd-Zr-Zn系合金. 通过对合金组织的分析, 以及Nd对组织性能影响的研究, 试制出了Nd添加量合理的Mg-Nd-Zr-Zn合金. 经过测试, 认为Nd添加量的增加提高了合金的250 ℃高温抗拉强度, 当Nd添加量超过2.8%时, 合金的高温强化作用不十分显著. Mg-Nd-Zr-Zn合金在250 ℃时的拉伸断裂方式主要是韧性断裂.     

儿童易疲劳与血清中微量元素含量的相关性研究

测定了1562名儿童(其中包括153名易疲劳儿童)血清中Zn、Fe、Cu、Ca、Mn和Pb的含量。研究发现,易疲劳儿血清Ca含量(84.4±12.5μg/mL)显著低于对照组儿童(88.5 4±13.4μg/mL),P<0.05;Fe含量(1.094±0.22μg/mL)显著高于对照组儿童(1.07 4±0.22μg/mL),P<0.05;Mn含量(0.040 4±0.035μg/mL)非常显著高于对照组儿童(0.035 4±0.013μg/mL),P<0.001。