Frequency and voltage-dependent electrical and dielectric properties of Al/Co-doped PVA/p-Si structures at room temperature

In order to investigate of cobalt-doped interracial polyvinyl alcohol （PVA） layer and interface trap （Dit） effects, A1/p- Si Schottky barrier diodes （SBDs） are fabricated, and their electrical and dielectric properties are investigated at room temperature. The forward and reverse admittance measurements are carded out in the frequency and voltage ranges of 30 kHz-300 kHz and -5 V-6 V, respectively. C-V or er-V plots exhibit two distinct peaks corresponding to inversion and accumulation regions. The first peak is attributed to the existence of Dit, the other to the series resistance （Rs）, and interfacial layer. Both the real and imaginary parts of dielectric constant （er and err） and electric modulus （Mr and Mrr）, loss tangent （tan~）, and AC electrical conductivity （aac） are investigated, each as a function of frequency and applied bias voltage. Each of the M~ versus V and Mrr versus V plots shows a peak and the magnitude of peak increases with the increasing of frequency. Especially due to the Dit and interfacial PVA layer, both capacitance （C） and conductance （G/w） values are strongly affected, which consequently contributes to deviation from both the electrical and dielectric properties of A1/Co-doped PVA/p-Si （MPS） type SBD. In addition, the voltage-dependent profile of Dit is obtained from the low-high frequency capacitance （CLF-CHF） method.     

Deposition of ZnS thin film by ultrasonic spray pyrolysis: effect of thickness on the crystallographic and electrical properties

Zinc sulfide (ZnS) thin films have been deposited on Si (1 0 0) substrate using ultrasonic spray pyrolysis. X-ray diffraction (XRD) analysis revealed that the films are (0 0 2) preferentially oriented with c-axis-oriented wurtzite structure. The crystallinity has been found to improve with film thickness in the 180–6000 nm range. Film structure has been analyzed by XRD, scanning electron microscope, FTIR, and Raman spectroscopies, while the stoichiometry has been verified by energy-dispersive spectroscopy and particle-induced X-ray emission techniques. Electrical properties of the grown films were characterized by current–voltage and capacitance–voltage measurements where, the films show better conducting behavior at higher thickness.     

Reliability of flexible electrically conductive adhesives

Based on our previous work about electrically conductive adhesives (ECAs), a flexibilizer named 1,3‐propanediol bis (4‐aminobenzoate) was used to fabricate flexible ECAs (FECAs). ECAs, FECAs, and electronic devices connected by them were carried out the hot and humid aging test under constant humidity level of 85% relative humidity at 85 °C for 600 h. After aging, the bulk resistance change of ECAs was about 26%, that of FECAs was a little higher, about 29%. The contact resistance change of devices connected by ECAs and FECAs was very great, about 450% and 410%, respectively. The bonding area at connection interface between colloids and devices had delamination, even cracks. The delamination of ECAs was calculated about 60%, the average shear strength of ECAs was reduced about 45%, and those of FECAs were about 50% and 30%, respectively, so FECAs had a higher bonding stability in hot and humid environment. Copyright © 2012 John Wiley & Sons, Ltd.     

The effects of etching and deposition on the performance and stress evolution of open through silicon vias

The effects of silicon etching using the Bosch process and LPCVD oxide deposition on the performance of open TSVs are analyzed through simulation. Using an in-house process simulator, a structure is generated which contains scalloped sidewalls as a result of the Bosch etch process. During the LPCVD deposition step, oxide is expected to be thinner at the trench bottom when compared to the top; however, additional localized thinning is observed around each scallop. The scalloped structure is compared to a structure where the etching step is not performed, but rather a flat trench profile is assumed. Both structures are imported into a finite element tool in order to analyze the effects of processing on device performance. The scalloped structure is shown to have an increased resistance and capacitance when compared to the flat TSV. Additionally, the scalloped TSV does not perform as well at high frequencies, where the signal loss is shown to increase. However, the scallops allow the TSV to respond better to an applied stress. This is due to the scallops’ enhanced range of motion and displacement, meaning they can compensate for the stress along the entire sidewall and not only on the TSV top, as in the flat structure.     

基于信捷PLC对细石混凝土泵电气系统的设计

为了推进细石混凝土泵的国产化,在保证产品性能的前提下,降低其电气系统的生产成本,采用以国产信捷PLC(Programmable Logic Controller)为主的控制元件对细石混凝土泵电气系统进行了设计。在保证细石混凝土泵使用稳定性的同时,降低了其电气系统的制造成本,提高了适用性。所设计电气系统经菏泽永安机械制造有限公司检验使用,实际应用情况良好。     

Non‐contact evaluation of the electrical conductivity of thin metallic films by eddy current microscopy

An eddy current microscopy technique to evaluate the electrical conductivity of thin metallic films in a non‐contact manner is reported. A narrow track formed in an approximately 100 nm thick Au film was prepared, and a Co–Cr coated magnetic tip was driven to oscillate above the track both with and without current passing through the track. Despite the absence of current, the electromagnetic interaction between the tip and the stray magnetic field from the track gave rise to a phase delay in the probe. This was due to an eddy current being induced within part of the track. Moreover, measurements of the phase change in the probe oscillation for different metallic films with thicknesses of about 100 nm found this to be proportional to the electrical conductivity of the film. Finally, the electrical conductivity of an Al film was evaluated using the eddy current microscopy technique. Copyright © 2012 John Wiley & Sons, Ltd.     

Kinetics of carbon steel dissolution in ammonium chloride solution containing sodium thiosulfate

The dissolution behavior of carbon steel in ammonium chloride (NH₄Cl) solution containing sodium thiosulfate (Na₂S₂O₃) of various concentrations (0.01 and 0.1 M) was investigated using electrochemical impedance spectroscopy (EIS) and other nonelectrochemical techniques. The weight loss and polarization measurements indicate a significant increase in the NH₄Cl corrosion rate of carbon steel on addition of Na₂S₂O_3. The EIS measurements exhibited two capacitive loops at multiple direct current (dc) potentials for both the concentrations. Electrical equivalent circuit (EEC) and reaction mechanism analysis (RMA) were employed to analyze the impedance data. A four-step mechanism with two intermediate adsorbate species of same charge was proposed to explain the dissolution behavior of carbon steel in the given system. The surface coverage values enumerated that the surface was entirely covered with adsorbed species unlike in the pure NH₄Cl system. Charge transfer resistance and polarization resistance values estimated from RMA parameters indicate the increase in a dissolution rate with dc potential. The surface morphology was inspected via field emission scanning electron microscopy, and the corrosion products including surface state of carbon steel electrode were analyzed using energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy.     

Vacancy-like defects in nanocrystalline SnO2: influence of the annealing treatment under different atmospheres

The study of electronic and chemical properties of semiconductor oxides is motivated by their several applications. In particular, tin oxide is widely used as a solid state gas sensor material. In this regard, the defect structure has been proposed to be crucial in determining the resulting film conductivity and then its sensitivity. Here, the characteristics of vacancy-like defects in nanocrystalline commercial high-purity tin oxide powders and the influence of the annealing treatment under different atmospheres are presented. Specifically, SnO₂ nanopowders were annealed at 330 °C under three different types of atmospheres: inert (vacuum), oxidative (oxygen) and reductive (hydrogen). The obtained experimental results are discussed in terms of the vacancy-like defects detected, shedding light to the basic conduction mechanisms, which are responsible for gas detection.     

Deflagration-to-detonation transition process for spherical aluminum dust/epoxypropane mist/air mixtures in a large-scale experimental tube

The deflagration-to-detonation transitions (DDTs) for clouds of spherical aluminum dust (SAD) mixed with air or epoxypropane mist (EPM) and air were investigated in a 29.6-m-long experimental tube of 199 mm in diameter. The clouds formed through the injection of SAD and SAD/liquid epoxypropane samples into the experimental tube. Explosions of the SAD/air mixture were initiated using a 7-m-long EPM/air cloud explosion ignited by a 40-J electric spark. Explosions in SAD/EPM/air clouds were initiated using a 1...