周视大像旋稳海天线向量角补偿算法

为使两轴周视光电探测系统在三自由度扰动和大像旋条件下搜索并跟踪水面目标,在虚拟天际线焦平面像五自由度解析表达式基础上,推导出焦平面坐标系铅直轴的方向向量和该坐标系下海天出射平面法向量夹角的余弦表达式.该式求反余弦后减π/2,得到焦平面铅直坐标轴的方向向量和海天出射平面法向量小于π/2的夹角,该夹角的0.5倍作为俯仰反射镜的净作动量,目的是克服非线性像旋使包含目标信息的虚拟海天线的像线通过焦平面中心.该算法与方位补偿算法联动能够使目标像点始终逼近焦平面原点.通过数学模型仿真和真实工况试验都验证了俯仰机构位置环海天线向量角补偿算法的合理性.     

Quantitative Surface Chirality Detection with Sum Frequency Generation Vibrational Spectroscopy: Twin Polarization Angle Approach

介绍了一种新的表面和频振动光谱方法: 定量手性检测中的双偏振角方法. 一般来讲表面光谱信号中非手性项贡献最强,而纯界面手性信号要比非手性信号弱两到三个数量级. 因此在和频振动光定量测量和分析界面手性的贡献问题上存在困难. 在和频振动光谱的双偏振角方法中,通过固定入射红外光偏振方向,并同时改变入射可见光和初涉和频信号光的偏振角进行测量. 这样所得到的偏振依赖的和频振动光谱信号能够直接给出界面手性贡献的特征,并 且能够用于准确测量界面的手性和非手性贡献. 对双偏振角方法进行了描述,并且通过S和R手性的柠檬烯空     

LCOS大屏幕薄型背投电视广角投影物镜的设计

为了满足67英寸大屏幕LCOS背投电视的需要,设计了一款广角投影物镜.此广角投影镜头采用远心反远距结构,通过合理选用非球面和光学材料,设计的镜头具有视场大、投影距离短、工作距离长、相对孔径大、无渐晕、辐照度均匀等优点.在LCOS芯片奈奎斯特空间频率处的调制传递函数值高于0.5,色差仅约1/4像元,畸变低于5‰.     

Fabrication of 2D–3D photonic crystal heterostructures by glancing angle deposition

We fabricate 2D–3D photonic crystal heterostructures based on the silicon [001]-diamond:1 square spiral geometry using glancing angle deposition. We compare the normal incidence reflection properties of the fabricated 2D–3D heterostructures to simulated spectra generated using finite-difference time-domain calculations. Reflection peaks are observed, resulting from the presence of a photonic band gap, and defect modes are created by the 2D layer. Deterioration of the reflectance peaks with increased number of vertical spiral periods is observed. A series of square spiral structures are fabricated with a varying number of vertical periods to quantify the degradation of reflection peaks. At normal light incidence, a maximum reflection peak is observed from the film with three vertical periods. Beyond three spiral rotations, deterioration of the substrate-plane periodicity causes scattering losses.     

开槽前扩孔及复合角对气膜冷却的影响

本文对开槽前扩孔及在此基础上加30°、45°和60°不同角度复合角的气膜冷却结构进行了数值模拟,计算了指定冷却壁面的温度场分布以及冷却效率.结果表明:引入复合角后,能够改善冷却气膜在壁面的横向分布,复合角越大,气膜分布越均匀.在高吹风比下,复合角结构能够产生较大的气膜覆盖范围和较好的冷却效果.     

部分相干厄米-高斯列阵光束通过湍流大气传输的方向性

推导出了部分相干厄米-高斯(H-G)列阵光束通过湍流大气传输的二阶矩束宽和远场发散角的解析公式。采用远场发散角作为光束方向性的评价参数,研究了部分相干H-G列阵光束通过湍流大气传输的方向性。研究表明:在一定条件下,部分相干H-G列阵光束与对应的高斯光束不论在自由空间还是湍流大气中均具有相同的方向性。此外,进一步研究发现,在自由空间中,由远场发散角和归一化远场平均光强分布所表征的部分相干H-G列阵光束的方向性是不一致的,但湍流可以使得两种描述相一致。这一结论与高斯-谢尔模型(GSM)列阵光束的相关结论存在差异。在自由空间中,与高斯光束具有相同远场发散角的非相干合成的GSM列阵光束与对应的高斯光束具有相同的归一化远场光强分布。     

Planar Hall effect in biosensor with a tilted angle of the cross-junction

A typical planar Hall effect (PHE) sensor junction consists of two Hall bars that the bars appear normal to each other and the junction can have the required four terminals for current and voltage measurements. We are now introducing a tilted angle of the cross-junction and studying the role of the PHE therein. The results show that although there is a tilted angle of the cross-junction, the PHE voltage is remained constant. The result is interpreted by assuming the sensor material with the behavior of a basic single domain structure under the external magnetic field reversals. The calculations of the model are found to be in good concurrence with the experimental results.     

Characterization of electrodeposited Bi2S3 thin films by holographic interferometry

Optical non destructive evaluation methods, using lasers as the object illumination source, include holographic interferometry. It is widely used to measure stress, strain, and vibration in engineering structures. Double exposure holographic interferometry (DEHI) technique is used to determine thickness and stress of electrodeposited bismuth trisulphide (Bi₂S₃) thin films for various deposition times. The same is tested for other concentration of the precursors. It is observed that, increase in deposition time, increases thickness of thin film but decreases stress to the substrate. The structural, optical and surface wettability properties of the as deposited films have been studied using X-ray diffraction (XRD), optical absorption and contact angle measurement, respectively. The X-ray diffraction study reveals that the films are polycrystalline with orthorhombic crystal structure. Optical absorption study shows the presence of direct transition with band bap 1.78 eV. The water contact angle measurement shows hydrophobic nature of Bi₂S₃ thin film surface.     

Counterion Association and Structural Conformation Change of Charged PAMAM Dendrimer in Aqueous Solutions Revealed by Small Angle Neutron Scattering

Our previous study of the structure change of poly(amidoamine) starburst dendrimers (PAMAM) dendrimer of generation 5 (G5) have demonstrated that although the overall molecular size is practically unaffected by increasing DCl concentration, a configurational transformation, from a diffusive density profile to a more uniform density distribution, is clearly observed. In the current paper, the focus is placed on understanding the effect of counterion identity on the inter-molecular structure and the conformational properties by studying the effect due to DBr using small angle neutron scattering (SANS) and integral equation theory. While the overall molecular size is found to be essentially unaffected by the change in the pD of solutions, it is surprising that the intra-molecular configurational transformation is not observed when DBr is used. The overall effective charge of a dendrimer is nearly the same for α < 1, independent of the type of acids. However, when α > 1, the effect of counterion identity becomes significant, the effective charge carried by a charged G5 PAPAM protonated by DBr becomes smaller than that of solutions with DCl. As a consequence, a counterion identity dependence of counterion association is revealed: Under the same level of molecular protonation, the specific counterion association, which is defined as the ratio of bound chloride anions to positively charged amines per molecule, is larger for the G5 PAMAM dendrimer charged by DBr than the one by DCl.     

采用CCD技术的微型光机电系统光开关测试方法

在研制基于微型光机电系统技术的光电器件过程中,需要精确测定器件在给定驱动条件下的运动情况。在对制作完成的光开关进行性能测试时,由于微型光机电系统光开关的几何尺寸的限制,如果要准确测定光开关微反射镜的运动位移。将会有一定的困难。提出了一种采用线阵CCD技术的光学测量方法,实现了对光开关悬臂梁在驱动电压作用下的旋转角度的精确测量。通过理论推导得到了悬臂梁扭转角度与可测量物理量的关系．通过求解方程得到了各个物理量的数值选择对于测量结果的影响,并且给定了测量时各个物理量的参考值。通过实验测量,误差小于10％,表明这是一种具有实际意义的测量方案。