Reducing Average and Peak Test Power Through Scan Chain Modification

Parallel test application helps reduce the otherwise considerable test times in SOCs; yet its applicability is limited by average and peak power considerations. The typical test vector loading techniques result in frequent transitions in the scan chain, which in turn reflect into significant levels of circuit switching unnecessarily. Judicious utilization of logic in the scan chain can help reduce transitions while loading the test vector needed. The transitions embedded in both test stimuli and the responses are handled through scan chain modifications consisting of logic gate insertion between scan cells as well as inversion of capture paths. No performance degradation ensues as these modifications have no impact on functional execution. To reduce average and peak power, we herein propose computationally efficient schemes that identify the location and the type of logic to be inserted. The experimental results confirm the significant reductions in test power possible under the proposed scheme.     

A Diepoxide Belonging to the Rare C1 Point Group

2,6- and 2,7-Dimethylanthracenes were reduced seriatim with lithium in liquid ammonia and lithium in methylamine to their 1,4,5,8,9,10-hexahydro derivatives. Two-fold epoxidation of these tetraenes provided the cis and trans diepoxides resulting from electrophilic attack at the inner double bonds. Trans diepoxide 1 has the very unusual characteristic of lacking a σ plane of symmetry but possessing an inversion center. As a consequence, the ¹H NMR spectrum of C₁-symmetric 1 is simplified relative to those of its isomers 5, 9, and 10.     

一种高并行度的H.264帧内预测器的VLSI设计

分析了帧内预测的17种模式,对于每个4×4大小块的16个像素点的不同模式的预测公式之间的相同运算,采用数字强度缩减的方法去除计算的冗余,提出了一种高并行度的帧内预测器,可以每个时钟周期处理16个像素点的预测值。基于SMIC0.18μm工艺,用verilog对该设计进行了VLSI实现,综合后的电路的关键路径最大时延为10ns,电路规模不超过1.4万门,数据吞吐率可以达到1600Msamples/s。从实现结果来看,与采用可重构方法的设计相比,该设计在相同的并行度下减小了电路面积,简化了控制逻辑。     

坦克红外特征控制技术评述

坦克红外特征控制对于提高坦克的战场生存能力具有重要意义。控制的主要方法有遮障、表面处理、外形技术、主动冷却、总体设计等。坦克红外特征的控制必须与其他波段，特别是射频波段的特性控制兼容。遮障和低发射率涂料是现役坦克红外特征控制的主要措施。而对未来的主战坦克，设计应是减少其系统特性的重要途径。     

Preparation of ultra fine nickel-copper bimetallic powder for BME-MLCC

The preparation of ultra fine nickel-copper bimetallic powder with two-stage chemical reduction method was investigated. Reductive sugar and hydrazine hydrate were employed as reducing agent in different reductive stage, respectively. Reaction of CuSO₄·5H₂O with reductive sugar at 70 °C gives cuprous oxide and copper particles, then as-prepared mixture and nickelous hydroxide were reduced by hydrazine hydrate, and nickel-copper powder having excellent dispersibility was prepared. Influences of nickel added on composition and dispersibility of powder were studied. TG/DTG/DTA of nickel-copper powder, which is stable in room temperature, were discussed with thermal analyzer. Relation of nickel content to oxidation temperature was investigated. Ni-Cu bimetallic powder particles have a fully coated structure when nickel content is up to 30%. As-prepared nickel-copper powder was applied in base metal electrode-multilayer ceramic capacitor (BME-MLCC). The end termination has high adhesion force, fairly good densification, low resistivity, excellent solderibility behavior and resistance behavior to soldering.     

置换环上的稳定矩阵

本文证明了置换环上的正则稳定矩阵是幂等矩阵和可逆矩阵的积,进一步证明了置换环上的正则稳定矩阵可以对角化。     

苯部分加氢制环己烯的非晶态Ru-M-B/ZrO2催化剂的表征

采用化学还原法，制备了高活性，高选择性非晶态RU-M-B/ZRO2催化剂，并将其用于催化苯部分加氢制环己烯，在140℃、5.0Mpa氢压下，苯转化40%时，环己烯选择性达到85%左右。环己烯最高收率达到52.1%，用XRD、SEM、BET比表面积测定等手段对摧化剂进行表征，XRD和SEM测试表明，RU-U-B/ZRO2属于非晶态，活性组分高度分散，XRD结果证实，在加氢过程中，非晶分解，RU晶化；温度愈高，RU晶化愈快，催化剂的活性、选择性与RU微晶的粒径有关，RU微晶粒径应控制在5nm左右，BET比表面积测定表明，ZRO2的负载提高了催化剂的比表面积，从而有利于活性组分的高度分散，并可阻止RU微晶的长大，讨论了B和ZRO2对提高选择性的作用。     

溶剂热还原合成Cr2O3纳米管(英)

Cr₂O₃ nanotubes with diameters of 80 nm and lengths of 550 nm were synthesized in a solvothermal reduction system at 180 ℃. The acetyl acetone (AcAc) and ethylene glycol (EG) were used as the chelate agent and the reductant respectively in the system. An intermediate compound-Cr(Ⅲ)(C₅H₇O₂)₃ was formed to force Cr₂O₃to crystallize along one direction.     

还原温度对超细K－Co－Mo催化剂合成低碳醇性能的影响

 用溶胶－凝胶法合成了K－Co－Mo催化剂．样品经不同温度还原后，用于低碳醇的合成．XRD和HRTEM结果表明，样品是超细粒子，粒子尺寸为2～5nm．考察了催化剂的还原温度和反应条件对催化剂性能的影响．实验结果表明，还原温度对催化剂的活性有较大的影响，最佳还原温度为500℃．最佳反应温度范围为310～330℃．升高压力和空速可以提高醇的收率和选择性．在空速14400h－1，压力6．0MPa和温度310℃的条件下，醇的选择性为55．8％，收率为520．0g／（kg·h），MeOH／C2＋OH为0．27．催化剂稳定性良好，在200h的寿命实验中，活性基本不变．与文献中催化剂相比，超细K－Co－Mo催化剂对合成醇具有较高的活性和选择性，尤其是对C2＋OH的合成明显高于其他合成醇催化剂体系．     

碲氢化钠还原亚胺的方法

本文报道一种还原亚胺的新方法。取代的芳基和脂肪基亚胺可以在较温和的条件下被碲氢化钠顺利地还原为相应的仲胺。