InSb,GaSb, and GaInSb grown using trisdimethylaminoantimony

GalnSb alloys as well as the constituent binaries InSb and GaSb have been grown by organometallic vapor phase epitaxy using the new antimony precursor trisdimethylaminoantimony (TDMASb) combined with conventional group III precursors trimethylindium (TMIn) and trimethylgallium (TMGa). InSb layers were grown at temperatures between 275 and 425°C. The low values of V/III ratio required to obtain good morphologies at the lowest temperatures indicate that the pyrolysis temperature is low for TDMASb. In fact, at the lowest temperatures, the InSb growth efficiency is higher than for other antimony precursors, indicating the TDMASb pyrolysis products assist with TMIn pyrolysis. A similar, but less pronounced trend is observed for GaSb growth at temperatures of less than 500°C. No excess carbon contamination is observed for either the InSb or GaSb layers. Ga_1-xIn_xSb layers with excellent morphologies with values of x between 0 and 0.5 were grown on GaSb substrates without the use of graded layers. The growth temperature was 525°C and the values of V/III ratio, optimized for each value of x, ranged between 1.25 and 1.38. Strong photoluminescence (PL) was observed for values of x of less than 0.3, with values of halfwidth ranging from 13 to 16 meV, somewhat smaller than previous reports for layers grown using conventional precursors without the use of graded layers at the interface. The PL intensity was observed to decrease significantly for higher values of x. The PL peak energies were found to track the band gap energy; thus, the luminescence is due to band edge processes. The layers were all p-type with carrier concentrations of approximately 10¹⁷ cm³. Transmission electron diffraction studies indicate that the Ga_0.5In_0.5 Sb layers are ordered. Two variants of the Cu-Pt structure are observed with nearly the same diffracted intensities. This is the first report of ordering in GalnSb alloys.     

Gelation of poly(n-butylisocyanate) in benzene

Poly (n-butylisocyanate)-benzene solutions prepared by solubilization at 45°C, followed by aging at room temperature were found to be metastable for months, although, eventually, they separated into a birefringent polymer-rich phase and an isotropic solution. These metastable solutions, as well as isothermally phase-separated biphasic samples, flowed and exhibited dynamic moduli indicative of low polymer connectivity. By contrast samples prepared by a freeze-thaw cycle were uniformly and highly birefringent and showed network (gel) behavior at room temperature. The mechanism of gel formation is most likely the exclusion of the polymer from the benzene crystal during crystallization, forcing the polymer to align and exist at grain boundaries. Films formed from solutions have different moduli than those formed from gels, and are consistent with the proposed mechanism.     

轴端沟槽底部激光强化工艺参数优化研究

分析了选用不同激光能量密度对HT300进行表面强化处理时，材料表面呈现的四种状况；未相变硬化、相变硬化、表面微熔与表面熔凝的金相组织。根据工艺要求，选取相变硬化方法对轴端沟槽底表面进行处理。分析了工件激光处理方法并通过试验研究，寻找轴端沟槽底部激光强化工艺参数；激光功率（P）、光斑直径（D）及扫描速度（V）的优化组合。硬度测试及耐磨性能试验表明：激光相变处理和激光熔凝处理后轴端沟槽底部表面较表面感应淬火硬度分别提高7%和34%，绝对磨损体积分别下降了13%和25%。实践证实，对轴端沟槽底部激光相变硬化处理方法较其他表面处理方法工艺简单，加工工件符合技术要求，试验结果对零件表面处理提供了可靠依据。     

Formation of GaAsP interface layers monitored by reflectance anisotropy spectroscopy

Reflectance anisotropy spectroscopy (RAS) has been used to study As-by-P exchange during metalorganic vapor phase epitaxy. The study focuses on the processes occurring during switching from GaAs to GaInP, especially the effect of purging PH₃ over a GaAs surface. GaAsP/GaAs superlattices of different periodicity were grown and the P-content was determined by high-resolution x-ray diffraction and correlated to the RAS spectra. From the temperature dependence of the P-content, an activation energy of 0.56 eV was estimated for the incorporation mechanism. In addition to the insights into the processes at mixed group-V heterointerfaces, our study demonstrates the reproducibility of RAS transients that thus can be used for process monitoring.     

Quantitative evaluation of two-dimensional dynamic deformations using digital holography

An optical system for the parallel evaluation of in- and out-of-plane dynamical deformations will be described. A double pulse laser with pulse separation in the microsecond range is used for the investigations. Two separate interferograms of an object under test, in its undeformed and deformed state, are recorded in a few microseconds. The object is illuminated from two different directions and imaged onto a CCD sensor. This produces two sensitivity vectors. The reference beams have different directions in order to produce two directional spatial carriers. The Fourier method is used for quantitative evaluation, and the measurements along different sensitivity vectors are separated in the Fourier domain. The phases of the two interferograms are obtained from the complex amplitudes and the two dimensional deformation is calculated from the phases. Experimental results are presented.     

Determination of the liquidus lines and isotherms of the Hg-Zn-Te system by a modified direct observation method

The modified direct observation method is employed for the determination of the liquidus lines in the (Hg_{1_x}Zn_x)_{1_y}Te_y, ternary system. The liquidus temperatures of the ternary samples of various compositions withx from 0.05 to 0.30 andy from 0.5 to 0.9 are measured. The temperature-composition phase diagrams and some liquidus isotherms are established for this system.     

窄带中频数字接收机高速信号处理技术

窄带中频数字接收机在雷达对抗侦察中得到了广泛应用，其高速信号处理技术是目前研究的重点。本文详细介绍了数字雷达告警接收机高速信号处理技术的发展现状和关键技术，最后通过对该技术的全面分析指出了值得深入研究的领域。     

Quantitative theory of living free‐radical polymerization. III. Calculation of copolymerization products' spinodal

The problem of finding conditions of the loss of thermodynamic stability by the reaction system was solved on the basis of the developed theory of living free‐radical copolymerization. The spinodal's calculations were carried out for a significant number of systems differing in the values of kinetic, stoichiometric, and thermodynamic parameters. Analysis of the results of such calculations revealed some regularities in the spinodal curves' behavior and permitted us to classify their possible topological types. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 892–902, 2003     

Insight into chain dimensions in PEO/water solutions

Small‐Angle Neutron Scattering has been performed from poly(ethylene oxide) in deuterated water at temperature ranging from 10 to 80 °C. A simple fitting model was used to obtain a correlation length and a Porod exponent. The correlation length L characterizes the average distance between entanglements in the semidilute region and is proportional to the individual coil sizes in the dilute region. L was found to increase with temperature in the semidilute region but it decreases with temperature in the dilute region. This decrease is the precursor to the single‐chain collapse which applies to very dilute polymer solutions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2196–2200, 2007     

Solvothermal synthesis of TiO2: anatase nanocrystals and rutile nanofibres from TiCl4 in acetone

This work reports a new synthetic approach for single‐phase TiO₂ nanomaterials by solvothermal treatment of titanium tetrachloride in acetone at 80–110 °C. Small, uniform, and yet size‐tunable (5–10 nm) anatase titania nanocrystallites were obtained using a low concentration of TiCl₄ in acetone (i.e., at molar ratios of TiCl₄/acetone ≤ 1:15) in the temperature range of 80–110 °C, while rutile nanofibers were synthesized using a high concentration of TiCl₄ (e.g., TiCl₄/acetone = 1:10) at 110 °C. Copyright © 2007 John Wiley & Sons, Ltd.