Effects of initial crystal size of diamond powder on surface residual stress and morphology in polycrystalline diamond (PCD) layer

Polycrystalline diamond compacts (PDC) were synthesized using diamond powder of average crystal size 3-20 μm by the Ni 70 Mn 25 Co 5 alloy infiltration technique at high temperature and high pressure (HPHT).The surface residual stress of polycrystalline diamond (PCD) layer was measured using micro-Raman spectroscopy with hydrostatic stress model and X-ray diffraction (XRD).Measurements of the stress levels of PCDs show that the residual compressive stresses range from 0.12 to 0.22 GPa,which increase with th...     

A Fast Electrochemical Quartz Crystal Microbalance,which Acquires Frequency and Bandwidth on Multiple Overtones

An electrochemical quartz crystal microbalance (EQCM) is described, which measures the shifts of frequency and bandwidth on multiple harmonics with a time‐resolution of 10 milliseconds. The technique requires the process under study to be repetitive. Examples are square wave amperometry and cyclovoltammetry. Data acquisition is fast because the raw data consist of traces of the electrical admittance at fixed frequencies . A few (∼10) such time traces are acquired sequentially at a set of frequencies evenly spaced around the crystal's resonance. Since all time‐traces are triggered by the same repetitive process, plots of the conductance G (ω_i , t ) and the susceptance B (ω_i , t ) from constant time delays, t , versus frequency can be produced a posteriori. The shifts, ΔG (ω_i ) and ΔB (ω_i ) quantify a difference between two resonance curves, pertaining to the sample's reference state and the state at time t . Fitting a difference of two resonance curves to these data, one obtains shifts of frequency, Δf (t ) and shifts of bandwidth, ΔΓ(t ), versus time. This procedure is repeated for the different overtones. Given the repetitive nature of the process, one may accumulate and average, which lowers the noise down to a few tens of mHz. The capabilities of this instrument are demonstrated with two examples, which are copper deposition/dissolution and electro‐responsivity of a polymer film containing weakly acidic side groups.     

A moving particle semi‐implicit method for free surface flow: Improvement in inter‐particle force stabilization and consistency restoring

The moving particle semi‐implicit (MPS) method has been widely applied in free surface flows. However, the implementation of MPS remains limited because of compressive instability occurred when the particles are under compressive stress states. This study proposed an inter‐particle force stabilization and consistency restoring MPS (IFS‐CR‐MPS) method to overcome this numerical instability. For inter‐particle force stabilization, a hyperbolic‐shaped quintic kernel function is developed with a non‐negative and smooth second order derivative to satisfy the stability criterion under compressive stress state. Then, a contrastive study is conducted on the contradiction between the common understanding of the conventional MPS hyperbolic‐shaped kernel function and its performance. The result shows that the conventional MPS hyperbolic‐shaped kernel function can easily cause violent repulsive inter‐particle force and then lead to the compressive instability. Therefore, the first order derivative of the modified hyperbolic‐shaped quintic kernel function is recommended as the form of the contribution of the neighbor particles to achieve a more stable inter‐particle repulsive force. For consistency restoring, the Taylor series expansion and the hyperbolic‐shaped quintic kernel are combined to improve the accuracy of the viscosity and pressure calculation. The IFS‐CR‐MPS algorithm is subsequently verified by the inviscid hydrostatic pressure, jet impacting, and viscous droplet impacting problems. These results can be used for choosing kernel function and the contribution of neighbor particles in particle methods. Copyright © 2016 John Wiley & Sons, Ltd.     

Compressive advection and multi‐component methods for interface‐capturing

This paper develops methods for interface‐capturing in multiphase flows. The main novelties of these methods are as follows: (a) multi‐component modelling that embeds interface structures into the continuity equation; (b) a new family of triangle/tetrahedron finite elements, in particular, the P₁DG‐P₂(linear discontinuous between elements velocity and quadratic continuous pressure); (c) an interface‐capturing scheme based on compressive control volume advection methods and high‐order finite element interpolation methods; (d) a time stepping method that allows use of relatively large time step sizes; and (e) application of anisotropic mesh adaptivity to focus the numerical resolution around the interfaces and other areas of important dynamics. This modelling approach is applied to a series of pure advection problems with interfaces as well as to the simulation of the standard computational fluid dynamics benchmark test cases of a collapsing water column under gravitational forces (in two and three dimensions) and sloshing water in a tank. Two more test cases are undertaken in order to demonstrate the many‐material and compressibility modelling capabilities of the approach. Numerical simulations are performed on coarse unstructured meshes to demonstrate the potential of the methods described here to capture complex dynamics in multiphase flows. Copyright © 2015 John Wiley & Sons, Ltd.     

InSb红外探测器芯片粘接工艺研究

基于InSb红外探测器的封装特点,采用正交试验法研究了芯片粘接过程中基板平整度、粘接剂抽真空时间、配胶时间、固化条件等工艺参数对芯片性能及可靠性的影响。通过计算极差和方差分析了各因素对芯片可靠性的影响大小。结果表明,固化条件对粘接后芯片的性能影响最大,其次是配胶时间,而抽真空时间和基板平整度影响相对较小。针对极差分析得出的较优参数组合和较差参数组合,利用X射线衍射(XRD)研究了不同参数组合对晶片粘接的应力大小,所得结果与正交试验一致。     

水胁迫下典型盐生植被梭梭光谱特征分析

荒漠地区由于气候干燥，降水稀少，水分常成为制约植被生长的因素之一，水分胁迫对植物长势和产量的影响比任何其他胁迫都要大。随着高光谱技术的发展，国内外已有众多学者利用高光谱数据研究植被遭受胁迫作用，然而这些研究对象多集中于甜菜、棉花、玉米、水稻等作物，针对干旱区盐生植被遭受胁迫作用的研究较少。梭梭作为荒漠、半荒漠地区的典型盐生植被之一，具有极高的经济和生态效益。选择梭梭作为研究对象，培育一年生梭梭，并设置三个水分梯度，形成受不同水分量胁迫的梭梭。使用原始光谱、红边位置参数，结合植被指数及二维相关光谱研究其叶片光谱特征，为干旱区利用高光谱遥感监测盐生植被提供借鉴。结果表明：(1)分析梭梭叶片反射光谱曲线发现，在可见光至中红外各波段范围内，受不同水分量胁迫作用的梭梭叶片光谱反射率有显著差异。在可见光(350～610 nm)波段，各水分处理的梭梭叶片反射率依次为100 mL>500 mL>200 mL，这是由于100和200 mL水分促进梭梭内部叶绿素合成，使该波段反射率降低，而过多的水分(500 mL)对梭梭内部的叶绿素合成没有更大的促进作用。在红光区(611～738 nm)，随着水分量的增多，受不同水分量胁迫的梭梭叶片光谱反射率依次减小。在738～1 181和1 228～1 296 nm波段，受不同水分量胁迫作用的梭梭叶片光谱反射率为：200 mL>100 mL>500 mL；在1 182～1 227 nm波段，受不同水分量胁迫作用的梭梭叶片光谱反射率为：100 mL>200 mL>500 mL。这是由于植被细胞结构对近红外区域的反射率影响较大，因而受不同水分胁迫作用的梭梭叶片光谱反射率有显著差异。在1 300～1 365和1 392～1 800 nm波段，受各水分胁迫作用的梭梭叶片反射率为：100 mL>200 mL>500 mL。这表明在500 mL水分胁迫量范围内，水分越多，叶子的细胞液、细胞膜对水分的吸收能力越强，使得反射率下降。通过对原始光谱求取一阶导数并提取红边位置参数发现，各水分处理下的梭梭叶片一阶微分光谱曲线中红边位置未发生移动。这是由于梭梭在长期的干旱环境影响下，形成了特殊的适应机制，水分对其红边位置影响不敏感。(2)选取若干植被指数分析各水分处理下的梭梭光谱指数变化。当水分胁迫量由100 mL增至200 mL时，WI/NDWI，MSI和NDII指数值变化显著，可用于研究水分胁迫下梭梭的光谱特征。(3)使用二维相关光谱技术分析受各水分胁迫作用的梭梭光谱特征，得出在100 mL水分胁迫下，在536，643，1 219和1 653 nm波段处，吸收峰对水分的微扰敏感；在200 mL水分胁迫下，在846和1 083 nm波段处，吸收峰对水分的微扰敏感；在500 mL水分胁迫下，在835和1 067 nm波段处，吸收峰对水分的微扰敏感。总之，在近红外波段，与100 mL水分量相比，梭梭受200和500 mL水分量胁迫时，吸收峰对水分的微扰敏感度上升。由100 mL水分胁迫下梭梭的二维同步相关谱图可知，1 044和1 665 nm，1 072和903 nm，903和1 264 nm，1 230和1 061 nm波段处形成正交叉峰，表明这些波段处光谱强度随水分的干扰同时变化。     

Degradation of a polyester‐urethane coating: Physical properties

In this article we studied the evolution of thermomechanical properties of a polyester‐urethane coating during degradation under different degradation conditions, i.e., aerobic and anaerobic conditions with and without dry/wet cycling during degradation. Dynamic mechanical and thermal analyses show that under aerobic conditions the coatings become stiffer and more brittle in the glassy state. This stiffening is probably due to the increase in the amount of hydrogen bonding and the formation of oxidized groups which increase the polarity of the material and enhance the interactions of the polymer segments. However, oxidation reactions result in a considerable decrease in cross‐link density and stiffness in the rubbery state. Both changes, in the glassy and rubbery states, give rise to development of internal stresses. These stresses increase as the degradation process proceeds. Nevertheless, for samples exposed to anaerobic conditions, the stiffness remains constant in the glassy state and the cross‐link density slightly increases as a result of degradation. This reconfirms the dominance of the effect of oxidation reactions on the mechanical failure of the coatings. Oxygen permeation measurements show a more‐or‐less time‐independent diffusion coefficient and a gradual decrease in solubility of oxygen as a function of exposure time. This results in a slight decrease in oxygen permeation (mainly in the early stage of the degradation) as degradation proceeds. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 659–671     

Improved bias stress stability of In–Ga–Zn–O thin film transistors by UV–ozone treatments of channel/dielectric interfaces

Possibility of improving the bias stress stability of amorphous In–Ga–Zn–O thin film transistors (a-IGZO TFTs) was explored by irradiating the channel/dielectric interface with ultraviolet (UV) light during the device fabrication process. The UV treatment of the channel/dielectric interface did not cause significant changes in the device performance itself. However, when the TFTs were tested under prolonged gate bias stress, the device with longest UV treatment showed the smallest time dependence of threshold voltage shift. This accompanied the smallest changes in the field effect mobility and subthreshold swing with extended bias stress. Such improvements in bias stress stability are attributed to the modification of the channel/dielectric interface due to the UV-generated ozone that in turn decreased the interface trap density and structurally modified the interface region on the dielectric side to prevent the redistribution of the trapped charges.     

硅衬底GaN基LED薄膜芯片的应力调制

将Si衬底GaN基LED外延薄膜经晶圆键合、去硅衬底等工艺制作成垂直结构GaN基LED薄膜芯片,并对其进行不同温度的连续退火,通过高分辨X射线衍射(HRXRD)研究了连续退火过程中GaN薄膜芯片的应力变化。研究发现:垂直结构LED薄膜芯片在160~180℃下退火应力释放明显,200℃时应力释放充分,GaN的晶格常数接近标准值。继续升温应力不再发生明显变化,GaN薄膜的晶格常数只在标准晶格常数值附近波动。扫描电子显微镜给出的bonding层中Ag-In合金情况很好地解释了薄膜芯片应力的变化。     

Geometric derivation of the microscopic stress: A covariant central force decomposition

We revisit the derivation of the microscopic stress, linking the statistical mechanics of particle systems and continuum mechanics. The starting point in our geometric derivation is the Doyle–Ericksen formula, which states that the Cauchy stress tensor is the derivative of the free-energy with respect to the ambient metric tensor and which follows from a covariance argument. Thus, our approach to define the microscopic stress tensor does not rely on the statement of balance of linear momentum as in the classical Irving–Kirkwood–Noll approach. Nevertheless, the resulting stress tensor satisfies balance of linear and angular momentum. Furthermore, our approach removes the ambiguity in the definition of the microscopic stress in the presence of multibody interactions by naturally suggesting a canonical and physically motivated force decomposition into pairwise terms, a key ingredient in this theory. As a result, our approach provides objective expressions to compute a microscopic stress for a system in equilibrium and for force-fields expanded into multibody interactions of arbitrarily high order. We illustrate the proposed methodology with molecular dynamics simulations of a fibrous protein using a force-field involving up to 5-body interactions.