Design considerations and an example of application of an in-house made TG-MS interface

The design, the abilities and a characteristic application of an in-house made interface for combining thermogravimetry (TG) with mass spectrometry (MS) are presented. The TG-MS interface consists mainly of three co-axial tubes. The position of the intermediate tube was determined after calculation of the temperature profile at the TG furnace exit tube. The inner tube position was determined taking into consideration its protection against condensation of heavy molecules and the time delay for the transfer of the evolved gases. This interface allows either continuous sampling and transferring of the evolved gases from the TG to the MS or repetitive introduction of short sampling pulses of TG evolved gases to MS. The interface is capable of coupling various commercial instruments. In the present work two configurations of this interface are demonstrated. Finally an example of application of this interface on forest fuel pyrolysis is presented. This revised version was published online in July 2006 with corrections to the Cover Date.     

Genetic engineering to enhance the selectivity of protein separations

The ability to recover and purify natural and recombinant proteins, and the costs of doing so remain a major task in introducing the potential products of biotechnology. The bases for separation range from specific binding onto tailored reagents to solubility and partitioning behavior governed by a mixed bag of size, charge, and hydrophobicity. In most cases, a combination of methods is used in sequence, and improvements in the selectivity at an early stage can enhance the effectiveness of subsequent (and usually more costly) steps. Genetic engineering provides a means of improving the selectivity within the context of existing separation methods. By this strategy, improvements in selectivity are sought by bestowing a distinctive property on the protein of interest. The primary sequence of amino acids is altered, such that the protein can be selectively removed from other components of the multicomponent mixture in which such products are commonly found. In this article, the range of these “distinctive properties” and their pairing with various separation methods will be reviewed. Specific examples from our work, in which a distinctive charge is provided via a polypeptide “purification” fusion tail, will be discussed. Separation methods we have used with these fusion proteins are precipitation, two-phase aqueous extraction, reversed micellar extraction, and ion exchange using both resins and membranes.     

Fibers and 3D mesh scaffolds from biodegradable starch-based blends: production and characterization

The aim of this work is the production of fibers from biodegradable polymers to obtain 3D scaffolds for tissue engineering of hard tissues. The scaffolds required for this highly demanding application need to have, as well as the biological and mechanical characteristics, a high degree of porosity with suitable dimensions for cell seeding and proliferation. Furthermore, the open cell porosity should have adequate interconnectivity for a continuous flow of nutrients and outflow of cell metabolic residues as well as to allow cell growth into confluent layers. Blends of corn starch, a natural biodegradable polymer, with other synthetic polymers (poly(ethylene vinyl alcohol), poly(epsilon-caprolactone), poly(lactic acid)) were selected for this work because of their good balance of properties, namely biocompatibility, processability and mechanical properties. Melt spinning was used to produce fibers from all the blends and 3D meshes from one of the starch-poly(lactic acid) blends. The experimental characterization included the evaluation of the tensile mechanical properties and thermal properties of the fibers and the compression stiffness, porosity and degradation behavior of the 3D meshes. Light microscopy picture of 3D meshes.     

Improved accuracy of quantitative XPS analysis using predetermined spectrometer transmission functions with UNIFIT 2004

The accuracy of quantitative XPS analysis can be improved using predetermined transmission functions. Two different calibration methods are used for estimating the transmission function T(E) of a photoelectron spectrometer, applying a survey spectra approach (SSA) and a quantified peak‐area approach (QPA) to minimize the quantification error. For the SSA method, Au, Ag and Cu spectra measured with the Metrology Spectrometer II have been used. The new QPA method was built up from Au 4f, Au 4d, Au 4p_3/2, Ag 3d, Ag 3p_3/2, Cu 3p, Cu 2p_3/2, Ge 3p and Ge 2p_3/2 standard peak areas, applying adequate ionization cross‐sections and mean free path lengths for different pass energies (10 and 50 eV), lens modes (large area, large area XL, small area 150) and x‐ray sources (Al/Mg Twin and Al Mono). In the energy range 200–1500 eV a transmission function T(E) = a₀ + b₁E (where a₀, b₁ and b₂ are variable parameters) was found to give an appropriate approximation for eight tested spectrometer settings, implementing the largest changes in the case of pass energy variations. Determination and application of the transmission functions were integrated in the XPS analysis software (UNIFIT 2004) and tested by means of an Ni90Cr10 alloy. The results demonstrate the practicability of the SSA and QPA methods, giving decreased errors of <8% in comparison with errors up to 38% obtained using Wagner's sensitivity factors. Copyright © 2005 John Wiley & Sons, Ltd.     

Linking Chiral Clusters with Molybdate Building Blocks: From Homochiral Helical Supramolecular Arrays to Coordination Helices

The synthesis of four new oxo‐centered Fe clusters ( 1 a – c , 2 ) of the form [Fe^III₃(μ₃‐O)(CH₂=CHCOO)₆] with acrylate as the bridging ligand gives rise to potentially intrinsically chiral oxo‐centered {M₃} trimers that show a tendency to spontaneously resolve upon crystallization. For instance, 1 a , [Fe^III₃(μ₃‐O)(CH₂=CHCOO)₆‐(H₂O)₃]⁺, crystallizes in the chiral space group P3₁ as a chloride salt. Crystallization of 1 b , [Fe₃(μ₃‐O)(C₂H₃CO₂)₆(H₂O)₃]NO₃?4.5H₂O, from aqueous solution followed by recrystallization from acetonitrile also gives rise to spontaneous resolution to yield the homochiral salt [Fe₃(μ₃‐O)(C₂H₃CO₂)₆‐(H₂O)₃]NO₃?CH₃CN of 1 c (space group P2₁2₁2₁). Furthermore, the reaction of 1 a with hexamolybdate in acetonitrile gives the helical coordination polymer {[(Fe₃(μ₃‐O)L₆(H₂O))(MoO₄)‐(Fe₃(μ₃‐O)L₆(H₂O)₂)]?2CH₃CN?H₂O}_∞ 2 (L: H₂C?CHCOO), which crystallizes in the space group P2₁. The nature of the ligand geometry allows the formation of atropisomers in both the discrete ( 1 a – c ) and linked {Fe₃} clusters ( 2 ), which is described along with a magnetic analysis of 1 a and 2 .     

低热-高压法制备PLGA多孔支架及其体外降解研究

采用低热-高压法制备了聚(dl-丙交酯／乙交酯)75／25(PLGA75／25)组织工程多孔支架。该方法避免了使用有机溶剂，支架的孔隙率在90％以上，孔径大小分布均匀。多孔支架经过酒精处理后，支架表面产生许多微小的凹陷；用藻酸钙改性处理后，支架形态保持良好。两种处理都使支架的压缩强度有所增大，亲水性增强。虽然孔隙率高的支架降解速率稍慢，但其体外降解规律基本一致：特性粘数争力学强度衰减快，而质量损失较慢，降解6周后，支架的质量损失仅为3％左右；体外降解3周后，支架的形态保持良好，可望在细胞移植争组织修复的早期发挥支撑作用。     

Thermally produced biodegradable scaffolds for cartilage tissue engineering

A novel process was developed to fabricate biodegradable polymer scaffolds for tissue engineering applications, without using organic solvents. Solvent residues in scaffolds fabricated by processes involving organic solvents may damage cells transplanted onto the scaffolds or tissue near the transplantation site. Poly(L-lactic acid) (PLLA) powder and NaCl particles in a mold were compressed and subsequently heated at 180 degrees C (near the PLLA melting temperature) for 3 min. The heat treatment caused the polymer particles to fuse and form a continuous matrix containing entrapped NaCl particles. After dissolving the NaCl salts, which served as a porogen, porous biodegradable PLLA scaffolds were formed. The scaffold porosity and pore size were controlled by adjusting the NaCl/PLLA weight ratio and the NaCl particle size. The characteristics of the scaffolds were compared to those of scaffolds fabricated using a conventional solvent casting/particulate leaching (SC/PL) process, in terms of pore structure, pore-size distribution, and mechanical properties. A scanning electron microscopic examination showed highly interconnected and open pore structures in the scaffolds fabricated using the thermal process, whereas the SC/PL process yielded scaffolds with less interconnected and closed pore structures. Mercury intrusion porosimetry revealed that the thermally produced scaffolds had a much more uniform distribution of pore sizes than the SC/PL process. The utility of the thermally produced scaffolds was demonstrated by engineering cartilaginous tissues in vivo. In summary, the thermal process developed in this study yields tissue-engineering scaffolds with more favorable characteristics, with respect to, freedom from organic solvents, pore structure, and size distribution than the SC/PL process. Moreover, the thermal process could also be used to fabricate scaffolds from polymers that are insoluble in organic solvents, such as poly(glycolic acid). Cartilage tissue regenerated from thermally produced PLLA scaffold.     

Novel photopolymerizable biodegradable triblock polymers for tissue engineering scaffolds: synthesis and characterization

For use in micro-patterned scaffolds in tissue engineering, novel diacrylated triblock macromers (PLA-b-PCL-b-PLA, PGA-b-PCL-b-PGA and PCL-b-PEO-b-PCL) were synthesized and characterized by Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR) and gel permeation chromatography (GPC). All diacrylated polymers were designed as triblock copolymers and involved biodegradable blocks of relatively non-polar epsilon-caprolactone (CL) and polar monomers such as glycolide (GA), lactide (LA) or ethylene oxide (EO). All triblock polymers were prepared in molecular weights of a few kilo daltons via the anionic ring-opening polymerization (ROP) of the corresponding lactide, glycolide or caprolactone using stannous octoate [Sn(Oct)(2)] as catalyst. The polymers had low polydispersity indices, ranging from 1.23 to 1.56. Biodegradable polymeric networks were prepared with conversions of 72-84% via photopolymerization of the triblock diacrylated polymers with 2,2-dimethoxy-2-phenylacetophenone (DMPA) as photoinitiator. PLA-b-PCL-b-PLA copolymers crumbled easily and were not suitable for micro-patterning. PGA-b-PCL-b-PGA copolymers had higher water contact angles than PCL-b-PEO-b-PCL and were also cytocompatible with Fibroblasts 3T3.     

球状蛋白质分子中氨基酸紧密接触对性质的研究

采用CSU软件 (Contactsofstructuralunits) ,对 61种球状蛋白质分子中氨基酸紧密接触对 (Residue residuecontact)进行了研究 .重点研究了不同氨基酸在形成远程紧密接触对 (Long rangecontact)和近程紧密接触对 (Short rangecontact)时的不同能力 .发现氨基酸Leu,Val,Ile,Met,Phe,Tyr,Cys,Trp(疏性氨基酸 ,H)比较容易形成远程紧密接触对 ,氨基酸Glu,Gln ,Asp ,Asn,Lys,Ser,Arg,Pro(亲水氨基酸 ,P)比较难形成远程紧密接触对 ,而氨基酸Ala,Gly,Thr,His(中性氨基酸 ,N)在形成远程紧密接触对时能力一般 .它们平均每个氨基酸可形成 6 0 3 ,3 64和 4 43个远程紧密接触对 .同时它们在形成近程紧密接触对时能力非常接近 ,平均每个氨基酸可形成的近程紧密接触对数目在 2 3 4～ 2 85变化 ,差别非常小 .亲水氨基酸 (P) ,中性氨基酸 (N)和疏水性氨基酸 (H)在蛋白质分子结构稳定性上起着不同的作用     

A study on the bioactivity of chitosan/nano-hydroxyapatite composite scaffolds for bone tissue engineering

In order to increase the biocompatibility and bioactivity of chitosan, hydroxyapatite had been in situ combined into chitosan scaffolds. The bioactivity of the composite scaffolds was studied by examining the apatite formed on the scaffolds by incubating in simulated body fluid and the activity of preosteoblasts cultured on them. The apatite layer was assessed using scanning electronic microscope (SEM), X-ray diffraction (XRD), Fourier-Transformed Infrared spectroscopy (FTIR) and weight measurement. Composite analysis showed that after incubation in simulated body fluid on both of the scaffolds carbonate hydroxyapatite was formed. With increasing nano-hydroxyapatite content in the composite, the quantity of the apatite formed on the scaffolds increased. Compared with pure chitosan, the composite with nano-hydroxyapatite could form apatite more readily during the biomimetic process, which suggests that the composite possessed better mineralization activity. Furthermore, preosteoblast cells cultured on the apatite-coated scaffolds showed different behavior. On the apatite-coated composite scaffolds cells presented better proliferation than on apatite-coated chitosan scaffolds. In addition, alkaline phosphatase activities of cells cultured on the scaffolds in conditioned medium were assessed. The cells on composite scaffolds showed a higher alkaline phosphatase activity which suggested a higher differentiation level. The results indicated that the addition of nano-hydroxyapatite improved the bioactivity of chitosan/nano-hydroxyapatite composite scaffolds. On the other hand, that is to say composition of substrates could affect the apatite formation on them, and pre-loaded hydroxyapatite can enhance the apatite-coating. It will also be significant in preparation of apatite-coating polymer scaffolds for bone tissue engineering.