大气状态下AFM阳极氧化加工Si的研究

Si纳米氧化线是构筑基于Si的纳米器件的基础。通过AFM针尖诱导阳极氧化加工的n型Si(100)的实验得到凸出的n型Si(100)氧化物高度和偏置电压成线性关系,与针尖扫描速度成负对数关系,并在前人的基础上深化了AFM针尖诱导氧化加工的机理和理论模型,得到了合适的加工条件为偏压8 V和扫描速度1μm/s。     

Fast handoff with reducing waste rate approach for wireless resources management in UMTS mobile networks

3G Wideband CDMA systems adopt the Orthogonal Variable Spreading Factor code tree as the channelization codes management for achieving high data rate transmission in personal multimedia communications. It assigns a single channelization code for each accepted connection. Nevertheless, it wastes the system capacity when the required rate is not powers of two of the basic rate. One good solution is to assign multiple codes for each accepted connection but it causes two inevitable drawbacks: long handoff delay and new call setup delay due to high complexity of processing with multiple channelization codes, and high cost of using more number of rake combiners. Especially, long handoff delay may result in more call dropping probability and higher Grade of Service, which will degrade significantly the utilization and revenue of the 3G cellular systems. Therefore, we propose herein an adaptive efficient codes determination algorithm based on the Markov Decision Process analysis approach to reduce the waste rate and reassignments significantly while providing fast handoff. Numerical results demonstrate that the proposed approach yields several advantages, including the lowest GOS, the least waste rate, and the least number of reassignments. Meanwhile, the optimal number of rake combiners is also analyzed in this paper. This research was supported in part by the National Science Council of Taiwan, ROC, under contract NSC-93-2213-E-324-018.     

质量控制图系统的实现及在SMT中的应用

本文将控制图理论与计算机技术相结合,开发了质量控制图系统.介绍了该系统的设计方案和关键技术问题,并以电子产品制造中监控SMT机的焊膏厚度为例说明了系统的应用.     

有线电视工程建设流程再造设计

从理论与实际工作相结合的角度出发,以淄博广电青鸟公司为研究对象,对有线电视网络工程建设流程的现状、存在的问题和原因进行细致深入分析,然后按照提出的再造方案的设计原则,设计了工程建设流程的再造方案,并对新旧流程进行比较。     

焊膏印刷工艺参数的选择与优化

表面贴装工艺流程的关键工序之一就是焊膏印刷,其工艺控制的好坏直接影响着装配的线路板的质量。通过对印刷工艺参数的分析,利用试验设计的方法来找出关键工艺参数,并加以优化设定,从而为控制工序参数奠定基础。     

积层板的制造方法

概述了积层板的开发背景、制造工艺和最近的开发动向。     

从RC5到RC6

论文详细描述并分析了从RC5到RC6的演化设计过程,在详细研究了RC6性能的同时,指出了应该如何从一个旧的密码设计出好的新密码。最后对RC6和Rijndael作了一些比较,指出各自在性能上的优缺点。     

On the effects of the packet size distribution on the packet loss process

Real-time multimedia applications have to use forward error correction (FEC) anderror concealment techniques to cope with losses in today’s best-effort Internet. The efficiency of these solutions is known however to depend on the correlation between losses in the media stream. In this paper we investigate how the packet size distribution affects the packet loss process, that is, the distribution of the number of lost packets in a block, the related FEC performance and the average loss run length. We present mathematical models for the loss process of the MMPP+M/D/1/K and the MMPP+M/M/1/K queues; we validate the models via simulations, and compare the results to simulation results with an MPEG-4 coded video trace. We conclude that the deterministic packet size distribution (PSD) not only results in lower stationary loss probability than the exponential one, but also gives a less correlated loss process, both at a particular average link load and at a particular stationary loss probability as seen by the media stream.Our results show that for applications that can only measure the packet loss probability, the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior. Our results show that the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior and thus can improve the queuing performance by decreasing the variance of its PSD.     

DC/DC电源中的电磁干扰及其对策

概述了电磁干扰(EMI)和电磁兼容(EMC)的基本知识，对DC／DC电源中的电磁干扰进行了综合分析，并给出了各自的解决方案。     

一个基于相邻像素兼容度的模糊加权平均滤波器

在文献[1]的基础上，提出几个改进的模糊加权平均滤波器。本文的方案不仅同时考虑了相邻像素对中心像素的兼容性以及中心像素对相邻像素的兼容性，而且还考虑到了权系数对局部环境的适应性。实验结果表明，该方法相比文献[1]中的模糊加权平均滤波器以及标准的均值滤波器、中值滤波器在噪声消除与边缘保留方面具有更好的性能。