双组元姿控发动机反流特性的DSMC模拟

为准确获得双组元姿控发动机的羽流及其反流特性,采用直接模拟蒙特卡罗(DSMC)方法结合可变软球(VSS)模型数值模拟以N2O4/MMH为推进剂的真空羽流。喷口参数由喷管流动的DSMC法计算得到。与文献比较表明本文计算程序可信。模拟结果表明,分子质量越小的气体越容易进入反流区;本文的计算条件下,在偏离X轴正向116°~140°范围内,组分数密度和质量流率以及温度均出现了最大值。     

狭义相对论效应──运动时钟变慢的计算机模拟演示实验

利用精炼的C语言进行程序设计，定量模拟狭义相结论的运动时钟变慢，并对处于两种不同时空观的时钟运行进行对比，使得时间膨胀效应变得直观。     

拼接式彩色等离子体大屏幕显示驱动电路的研究

针对拼接结构的高分辨率彩色等离子体大屏幕系统的应用，指出了刷新型电路模式的不足之处，提出了一种混合型模式的驱动电路。从彩色模块ＡＣＰＤＰ的结构特性出发，详细讨论了该电路的工作原理，驱动波形以及放电过程。     

三维目标旋转畸变不变光学相关滤波器组的设计

研究了三维目标旋转畸变不变光学相关滤波器组的设计原理，完成了滤波器组参数的计算和编码，以及光学相关识别的计算机模拟。     

Size dependence of self-diffusion in the hard-square lattice gas

A striking size dependence of the mean-square displacement of diffusing particles in the two-dimensional lattice gas of hard squares has been observed by Monte Carlo simulation. It is shown that the size effect is due to the formation of a stable cage structure in small lattices when the particle concentration is high. The formation of cages is governed by a new type of percolation problem related to bootstrap percolation.     

人工神经网络在激光加工温度场模拟中的应用

研究了人工神经网络在激光加工温度场模拟用的参数推算中的应用方法；并设计了相应的BP神经网络模型及软件；研究表明BP神经网络适用于对激光加工模拟的参数推算，其准确性优于回归分析法和函数插值法。     

Numerical Analysis and Simulation Analysis for Space‐Time Data

Spatio temporal dynamics of the positive column of a dc neon glow discharge is studied and investigated experimentally and theoretically. Spatio temporal analysis by means of biorthogonal decomposition method (BOD) gives insights into the mechanism of irregularity and can be employed for characterization of spatio‐ temporal complexity. In the weak nonlinear region, the wave dynamics is approximated by an amplitude equation of the Ginzburg‐Landau equation (CGLE) with complex coefficients and an additional integral term based on a fluid model. In the present work we deal with irregular spatio‐temporal data. A comparison between the numerical analysis of the experimental data and simulation results are studied. A good agreement between the dynamical behaviour for experimental space‐time data and theoretical simulation space‐time results was obtained. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A tentative approach to the direct simulation of drag reduction by polymers

An efficient technique for drag reduction uses dilute solutions of a few p.p.m. of polymers. A possible reduction in drag of up to 80% is achieved. Several experimental observations have been made which tend to indicate that the polymers modify the turbulence structures within the buffer layer. Flow visualisations have shown that the changes consist of a weakening of the strength of the streamwise vortices. Existing literature reveals no attempts of numerical simulation of this phenomenon. In this paper an approach is pursued by using a constitutive equation which relates the elongation viscosity to the local properties of the flow. According to this model this viscosity is large in zones where the amount of strain rate is greater than the amount of vorticity, and is zero when the vorticity exceeds the strain rate. Simulations have been performed in a “minimal channel” to give good resolution with a limited number of grid points. The accuracy of the method is tested by comparison with the results of other techniques. For simulations with polymers, quantitative comparisons cannot be made, but the results reproduce the qualitative outputs of the experiments. The mean streamwise velocity is modified in the buffer layer; the peak of the streamwise turbulent intensity, in wall units, increases and its maximum moves far from the wall; and the vertical turbulent intensity is largely reduced in the wall region. An interesting outcome from both the simulation and the experiments is that the strength of the longitudinal vortices is reduced when the polymers are present.     

二元合金微观偏析的相场法数值模拟

使用耦合溶质场的相场模拟研究了Ni-Cu二元合金枝晶生长过程中固相溶质扩散系数D_s 对枝晶形貌和微观偏析等的影响.计算结果表明，随着D_s的减少，固液界 面前沿溶质扩散层越薄，枝晶生长越有利，枝晶尖端生长的速度越大，侧向分支越发达；D< sub>s越小，固相中溶质成分的波动越强烈，随着D_s的增大，固相中溶质 成分的波动相应减小；溶质微观偏析程度随D_s的增大而减小. 关键词： 相场方法 微观偏析 固相扩散系数 数值模拟     

多级轴流压气机全工况特性计算

本文使用三维粘性流动计算软件Fine／Numeca,对某十五级轴流压气机进行了内流流场和全工况特性的数值计算尝试。分析了该压气机在设计工况和非设计工况的性能,同时把整机计算结果和前七级叶片的计算结果进行了比较。计算结果表明,当计算的级数较少时,目前的软件和硬件平台可以比较合理地预测压气机的全工况特性;而当计算的级数较多时,准确的数值模拟仍需要更为准确的多级模型和数值方法。