Structure of a poly(2,5‐benzimidazole)/phosphoric acid complex

As‐cast films of poly(2,5‐benzimidazole) exhibit uniplanar orientation in which the planes of the aromatic rings lie parallel to the film surface. Upon doping with phosphoric acid, the original crystalline order is lost, but the doped film can be stretched to produce films with uniaxial orientation. After thermal annealing at 540 °C, nine Bragg reflections are resolved in the fiber diagram, and these are indexed by an orthorhombic unit cell with the dimensions a = 18.1 Å, b = 3.5 Å, and c = 11.4 Å, containing four monomer units of two chains. The absence of odd‐order 00l reflections points to a 2₁ chain conformation, which is probably planar so that the aromatic units can be stacked along the b axis. The water and phosphoric acid contents of the crystalline structure cannot be determined exactly because of the presence of extensive amorphous regions that probably have different solvation. The best agreement between the observed and calculated intensities is for an idealized structure containing two phosphoric acids and two water molecules per unit cell. However, the phosphoric acid is probably present mainly in the form of pyrophosphoric acid and its higher oligomers. In addition, the X‐ray data are consistent with a more disordered structure containing chains with random (up and down) polarity and a lack of c‐axis registry. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2576–2585, 2004     

螺旋线径向挤压变形对其慢波结构冷测特性的影响

 介绍了用MAFIA软件的准周期边界条件计算螺旋线行波管慢波结构的色散和耦合阻抗，以及用ANSYS软件对螺旋线径向挤压变形建模的方法，并对螺旋线受挤压径向变形对其冷测特性的影响进行了详细的分析。结果表明:螺旋线径向挤压变形会导致相速增大，而在通常的变形范围内耦合阻抗也会增加；当变形继续增大时耦合阻抗上升到最大值后开始下降。     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

辐射加热金X光再发射时间测量

利用星光Ⅱ三倍频激光打双盘靶，研究了辐射加热材料的Ｘ光发射时间。激光脉冲能量４０～６０Ｊ、脉冲宽度６００～７００ｐｓ。通过两台时间关联的亚千Ｘ光能谱仪分别监测双盘靶初、次级发射Ｘ光谱，给出了辐射加热次级Ｘ光再发射时间。     

点状屏彩色显示管校正透镜优化设计

本文在条状屏彩色显象管校正透镜设计的基础上，提出了蹼状屏彩色显示管校正透镜的优化设计方法并给出了设计实例，通过计算机模拟电子束轨迹和光线追迹，分析了校正透镜面型修正程序的精度。     

折射率温敏式光纤温度传感器的理论模型

提出了折射率温敏式光纤温度传感器的理论模型，包括子午光线和偏射光线的影响，讨论了多模光纤的弯曲损耗，理论的分析和结果与实验相当一致。     

Dielectric effect on the rf characteristics of a helical groove travelling wave tube

A new type of partial-dielectric-loaded helical groove slow-wave structure (SWS) for millimetre wave travelling wave tube (TWT） is presented in this paper.The radio-frequency characteristics including the dispersion properties,the longitudinal electric field distribution and the beam-wave coupling impedance of this structure are analysed.The results show that the dispersion of the helical groove circuit is weakened,the phase velocity is reduced and the position of the maximum Ez is moved from the mouth to the inside of the groove after partially filling the dielectric materials in the helical groove SWS.Therefore,the dielectric-loaded helical groove SWS is suitable for a multi-beam TWT with broad band and high gain.     

显像（示）管阴极像黑洞状缺陷形成的原因及消除对策

本文通过有关理论依据和试验数据，着重阐述了在显像（示）管测试中，阴极像中心黑洞状缺陷产生的原因以及消除这种缺陷的处理方法。通过这种处理方法处理过的显像（示）管，其整体质量水平（尤其是真空度）将会得到明显的提高。     

A Tin(IV) Porphyrin with Two Axial Organometallic NCN‐Pincer Platinum Units

A tin(IV) porphyrin was combined with two axial NCN‐pincer platinum(II) fragments by utilizing the oxophilicity of the apical positions on the tin atom and the acidic nature of the NCN‐pincer platinum derived benzoic acid. The solid‐state structure determined by X‐ray crystallography revealed some close contacts between the pincer complexes and the meso‐p‐tolyl subsitutents of the porphyrin. It was shown by ¹H NMR spectroscopy that these close contacts were not present in solution and that this compound can potentially act as a novel building block for supramolecular architectures.