DSC Calibration During Cooling

A number of compounds are investigated for DSC calibration during cooling. Adamantane and Zn show fast reversible transitions and can be applied both for temperature and for heat calibration. A third compound, namely 4,4′-azoxyanisole, has a liquid crystal to isotropic liquid transition at 409 K. This compound can be used for temperature calibration. Heat calibration with this compound is more problematic because of the small heat effect and the construction of the baseline. Two other compounds, namely Hg and Pb, show a slight undercooling. Nevertheless they can be used for heat calibration, and possibly also for temperature calibration during cooling. This revised version was published online in August 2006 with corrections to the Cover Date.     

186Os和188Os双同位素溶液的制备及其中Os同位素丰度与含量的标定

在核反应堆中辐照高纯铼金属带 ,185Re和187Re通过 (n ,γ)反应后 ,经 β衰变产生186Os和188Os ,用H2 O2 和H2 SO4 将Re带溶解并同时将186Os和188Os蒸馏出 ,首先用 2 0 %NaOH溶液吸收 ,然后再将碱吸收液重新蒸馏 ,最后将186Os和188Os混合同位素保存在 2 5 %HCl介质中 ,用负离子热电离质谱仪 (NTIMS)标定其含量及同位素丰度。结果表明 ,91.4mg的高纯铼金属带 ,在辐照的累积通量为 1.32× 10 18n/cm2时 ,可产生Os 8.46 μg ,其186Os和188Os的同位素丰度分别为 6 0 .89%和 38.6 3%     

Elemental Analyses Using Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry (LA-ICP-MS) of Geological Samples Fused with Li2B4O7 and Calibrated Without Matrix-Matched Standards

 Laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) was used as a complementary technique to X-ray fluorescence (XRF), for multi-element analysis of geological samples fused with lithium-tetraborate Li₂B₄O₇). Different calibration strategies using external non-matrix matched reference materials were investigated. Various internal standards were tested, including the use of Li from the flux, and the use of the naturally occurring internal standards, Si or Ca. The use of a naturally occurring standard is not as efficient as this required a prior analysis of the samples using XRF. The obtained values for the analysis of geological reference materials were compared with consensus literature values, and satisfactory agreement was found. Laser pits, which were formed, had a diameter of 80 μm and 3–5 replicates on each fused disc were measured. The reproducibility of the method was better than 10% for concentrations above 1 μg/g and better than 15% for lower concentrations. The use of Li as the internal standard offers the possibility of multi-element determinations in geological samples, which have an unknown composition when the laser ablation analysis is carried out. However, using the calculated stoichiometric composition of the lithium-tetraborate for the calculation of the Li concentration leads to a constant deviation from the recommended values. Therefore, it was necessary to determine the Li concentration within each sample batch using at least one lithium tetraborate fused geological reference material. This resulting Li concentration in the beads was then used for all subsequent samples in a run. Limits of detection, reproducibility, deviation from reference values indicate the potential of LA-ICP-MS for such bulk analysis without matrix matched calibration standards.     

Determination of selected trace elements in marine biota samples with the application of fast temperature programs and solid sampling continuous source high resolution atomic absorption spectroscopy: method validation

Analytical procedure for the determination of As, Cd, Cu, Ni, Co and Cr in marine biota samples using solid sampling high-resolution continuum source atomic absorption spectrometry (HR CS AAS) and accelerated fast temperature programmes has been developed. Calibration technique based on the use of solid certified reference materials similar to the nature of the analysed sample and statistics of regression analysis were applied. A validation approach in line with the requirements of ISO 17025 standard and Eurachem guidelines was followed. Accordingly, blanks, selectivity, calibration, linearity, working range, trueness, repeatability and reproducibility, limits of detection and quantification and expanded uncertainty for all investigated elements were assessed. The major contributors to the combined uncertainty of the analyte mass fractions were found to be the homogeneity of the samples and the microbalance precision. Traceability to the SI system of units of the obtained with the proposed analytical procedure results was also demonstrated. The potential of the proposed analytical procedure based on solid sampling HR CS AAS technique was demonstrated by direct analysis of marine reference biota samples. Overall, the use of solid sampling HR CS AAS permits obtaining significant advantages for the determination of selected trace elements in marine biota samples, such as straightforward calibration, a high sample throughput, sufficient precision, a suitable limit of detection and reduced risk of analyte loss and contamination.     

Novel Approach to Two-Component Analysis Based on the Generalized Calibration Strategy

The generalized calibration strategy (GCS), developed and previously applied to chemical analysis, has been adapted to two-component (2C) analysis. According to the 2C-GCS procedure, a set of 10 calibration solutions containing a sample and standards of two analytes in well-defined composition was diluted. The measurements performed at a given dilution stage allow the concentration of both analytes in a sample to be evaluated with six apparent concentrations calculated with various mathematical approaches. As a result, the method allows the detection, examination, and elimination of nonlinear and interference effects with multiplicative and additive characteristics. To perform 2C-GCS automatically and effectively, a dedicated flow sequential injection system was designed to be fully controlled by a computer. Caffeine and paracetamol were determined in synthetic and pharmaceutical samples using this calibration approach. The analytes were determined with good precision and accuracy with low consumption of sample and standard solutions. On the basis of this experimental model, the influence of effects and tendencies in the examined analytical system was detected and evaluated.     

Economic evaluation for the optimal introduction of flexible manufacturing technology under rivalry

Unless procedures for the economic evaluation of flexible manufacturing technology are revamped, much of U.S. industry could repeat the experience of American automobile and steel companies from the recent past. The dynamic character of flexible manufacturing technology in terms of associated developments in microelectronics, a trend toward equipment modularity, and the increasing diversity of relevant markets make flexible manufacturing especially vulnerable to the weaknesses of conventional procedures for the justification of capital expenditures. Building on the work of V. Smith, M.I. Kamien and N.L. Schwartz, this paper presents optimization models from which economically reasonable plans can be derived for the implementation of flexible manufacturing technology. Although the assumptions of these models are not focused on the situation of a specific plant, model implications and the overall perspectives here on the economic evaluation of flexible system options should provide general guidance for manufacturing planners.     

A model for the economic evaluation of master city plans: a pilot study of Västerås,Sweden

The paper introduces the framework, problems addressed, objective function, types of variables and so on for a model designed to facilitate the economic evaluation of master city plans. The model presented here has been used in a pilot study of the city of Västerås, Sweden. It consists of three main parts, data, results and method. Some conclusions are drawn.     

The design of robust value-creating supply chain networks: A critical review

This paper discusses Supply Chain Network (SCN) design problem under uncertainty, and presents a critical review of the optimization models proposed in the literature. Some drawbacks and missing aspects in the literature are pointed out, thus motivating the development of a comprehensive SCN design methodology. Through an analysis of supply chains uncertainty sources and risk exposures, the paper reviews key random environmental factors and discusses the nature of major disruptive events threatening SCN. It also discusses relevant strategic SCN design evaluation criteria, and it reviews their use in existing models. We argue for the assessment of SCN robustness as a necessary condition to ensure sustainable value creation. Several definitions of robustness, responsiveness and resilience are reviewed, and the importance of these concepts for SCN design is discussed. This paper contributes to framing the foundations for a robust SCN design methodology.     

Metric inequalities for routings on direct connections with application to line planning

We consider multi-commodity flow problems in which capacities are installed on paths. In this setting, it is often important to distinguish between flows on direct connection routes, using single paths, and flows that include path switching. We derive a feasibility condition for path capacities supporting such direct connection flows similar to the well-known feasibility condition for arc capacities in ordinary multi-commodity flows. The condition can be expressed in terms of a class of metric inequalities for routings on direct connections. We illustrate the concept on the example of the line planning problem in public transport and present an application to large-scale real-world problems.     

MODELING HARVEST SCHEDULING IN MULTIFUNCTIONAL PLANNING OF FORESTS FOR LONGTERM WATER YIELD OPTIMIZATION

In this study, wood production and hydrologic functions of forests were accommodated within a planning procedure for separate working circles (areas dedicated to certain forest functions) that were delineated according to an Ecosystem‐Based Functional Planning approach. Mixed integer goal programming was used as the optimization technique. The timing and scheduling of a maintenance cutting (partial harvest) was the decision variable in the modeling effort, and an original formulation was developed as a multiobjective planning procedure. Four sample planning strategies were developed and model outputs were evaluated according to these strategies. Spatial characteristics of stands were considered, and used to prohibit the regeneration of adjacent stands during the same time period. Because of the positive relationship between qualified water production and standing timber volume in the forest, the model attempts to maximize qualified water production levels by increasing standing volume stocks in the forest through the delay of regeneration activities.