N,N-Dimethyl formamide facilitated formation of hexagonal boron nitride from boric acid

In this paper, we report on a promoting novel process for the formation of h-BN plates by using N,N-dimethyl formamide-treated boric acid (DMF-BA). Using this B source, the formation of h-BN can be indeed improved greatly compared to using pure boric acid (BA). This method effectively reduces the content of boric acid and amorphous boric oxide, enhancing the transformation rate of h-BN. For preparation of pure h-BN, it can obviously lower the resultant temperature without further purification process. Via graphitization index (G.I.) calculation and thermostability analysis, the pure h-BN plates obtained from the DMF-BA would be a promising candidate for raw material of c-BN and low-temperature applications in the air.     

富锂层状正极材料Li2Mn1-xTixO3的合成及电化学性能

应用简单的高温固相烧结法合成了Ti掺杂改性的Li₂MnO₃材料。电子扫描显微镜、X射线衍射以及X射线光电子能谱分析表明Ti元素取代Mn离子掺入到Li₂MnO₃晶格中,且掺杂能有效地抑制一次颗粒的团聚。电化学阻抗和恒流充放电测试结果表明,在2.0~4.6 V的电压窗口下,掺杂改性的样品Li₂Mn_0.9Ti_0.03O₃的首圈放电比容量达到209 mAh·g^-1,库仑效率为99.5%,循环40圈后容量保持率为94%;当电流密度增大到400 mA·g^-1时,掺杂改性的样品仍然可以放出120 mAh·g^-1比容量,远高于同等电流密度下未掺杂的Li₂MnO₃原粉的比容量（52 mAh·g^-1）。Ti掺杂可有效地改善Li₂MnO₃的循环稳定性和倍率性能,有利于促进该材料的商业化应用。     

Sol-gel Synthesis and Electrochemical Performance of Li4-xMgxTi5-xZrxO12 Anode Material for Lithium-ion Batteries

The anode materials Li_4?xMg_xTi_5?xZr_xO₁₂ (x=0, 0.05, 0.1) were successfully synthesized by sol‐gel method using Ti(OC₄H₉)₄, CH₃COOLi·2H₂O, MgCl₂·6H₂O and Zr(NO₃)₃·6H₂O as raw materials. The crystalline structure, morphology and electrochemical properties of the as‐prepared materials were characterized by XRD, SEM, cyclic voltammograms (CV), electrochemical impedance spectroscopy (EIS) and charge‐discharge cycling tests. The results show that the lattice parameters of the Mg‐Zr doped samples are slightly larger than that of the pure Li₄Ti₅O₁₂, and Mg‐Zr doping does not change the basic Li₄Ti₅O₁₂ structure. The rate capability of Li_4?xMg_xTi_5?xZr_xO₁₂ (x=0.05, 0.1) electrodes is significantly improved due to the expansile Li⁺ diffusion channel and reduced charge transfer resistance. In this study, Li_3.95Mg_0.05Ti_4.95Zr_0.05O₁₂ represented a relatively good rate capability and cycling stability, after 400 cycles at 10 C, the discharge capacity retained as 134.74 mAh·g^?1 with capacity retention close to 100%. The excellent rate capability and good cycling performance make Li_3.95Mg_0.05Ti_4.95Zr_0.05O₁₂ a promising anode material in lithium‐ion batteries.     

Separation of five oligostilbenes from Vitis amurensis by flow‐rate gradient high‐performance counter‐current chromatography

A rapid and efficient high‐performance counter‐current chromatography (HPCCC) method was developed to separate five oligostilbenes from the roots of Vitis amurensis. An n‐hexane/ethyl acetate/methanol/water system (4:8:4:10, v/v/v/v) was selected as an optimal two‐phase solvent system of which the upper phase was used as the stationary phase and the lower phase was used as the mobile one. Partition coefficient values for the target compounds under these optimized conditions were 0.28 ( 1 , ampleosin A), 7.12 ( 2 , (+)‐g‐viniferin), 2.26 ( 3 , vitisin A), 5.38 ( 4 , wilsonol C), and 11.23 ( 5 , vitisin B). Flow‐rate gradient HPCCC (4 mL/min in 0–70 min, 8 mL/min in 70–250 min) was applied to isolate the target compounds in as high purity as possible within the shortest possible run time. Under these conditions, ampelopsin A (12.1 mg), (+)‐g‐viniferin (10.4 mg), vitisin A (2.8 mg), wilsonol C (3.2 mg), and vitisin B (37 mg) were isolated with >95% purity from 150 mg of enriched oligostilbene extract. Although the K_D of the last eluted compound, vitisin B (K_D = 11.23), was relatively large, it was eluted in 115–145 min using the two‐phase solvent system. This study shows that HPCCC is an efficient tool for the isolation and purification of natural products.     

Atmospheric degradation mechanisms of a simulant organophosphorus pesticide isopropyl methyl methylphosphonate: A theoretical consideration

Calculations using density functional theory were performed to explore the mechanisms for atmospheric degradation of isopropyl methyl methylphosphonate (IMMP). The potential energy surface profiles for OH‐initiated reaction of IMMP were constructed, and all possible degradation channels were considered. Rate constants were further calculated using transition state theory. It was established from these calculations that H‐abstractions from alkyl groups have much lower energy barriers than substitutions of alkoxyl groups, and four possible H‐abstraction channels are competitive. Investigations into the secondary reactions under the presence of O₂/NO were also performed. It is shown that O₂ addition, reaction of peroxide radicals with NO to form RO radicals, and removal of ·RO are the major degradation pathways for alkyl radicals. Four selected products, CH₃OP(O)(CH₃)OC(O)CH₃, CH₃OP(O)(O)CH₃, (CH₃)₂CHOP(O)(CH₃)OH, and (CH₃)₂CHOP(O)(CH₃)OCH?O, are predicted to be the major products in this study. © 2013 Wiley Periodicals, Inc.     

Influence of oxygen flow rate on the surface chemistry and morphology of radio frequency (RF) magnetron sputtered zinc oxide thin films

Zinc oxide thin films were deposited, by radio frequency magnetron sputtering, on heated and unheated substrates. The oxygen flow rate was varied during deposition, and its effects on the structural and chemical properties of the films were investigated. The films had oriented c‐axis growth with nano‐crystallite size. Their surfaces manifested columnar microstructure, with a surface roughness that was suppressed by the introduction of oxygen. Chemical analysis showed that deposition under an oxygen atmosphere resulted in substantial reduction of oxygen vacancies, with a corresponding incorporation of chemisorbed species. Copyright © 2013 John Wiley & Sons, Ltd.     

Mathematical Modeling and Simulation of Corrosion Processes in Nigerian Crude Oil Pipelines

In this work, a corrosion prediction mathematical model for risk assessment in oil and gas production and transportation facilities has been created. This work focuses on partial pressure of carbon (iv) oxide, CO₂ and the operating temperature in process equipment and transportation facility pipes as a function of corrosion rate. The model equation formulated was based on the principle of multiple linear regressions of data. The final model representing the corrosion rate of crude oil equipment was obtained CR = b _o + b ₁ T + b ₂ P (CO ₂). The model was simulated using polymath software. The correlation between the experimental and simulated resulted obtained using root mean square deviation (coefficient of determination) was 99.74% which is high, suggesting that the relationship between the predictor and response variables is linear. The variation in the model equation is 0.0066374. This low value of the variance shows that the model is accurate.     

Study of Sorption of 2,4‐D on Outer Peristaltic Part of Waste Tire Rubber Granules

From this study it was evident that outer peristaltic parts of waste tire granules gave the highest removal. Film and pore diffusions are the major factors controlling rates of sorption from solution by porous adsorbents. For sorption of 2,4‐D on waste tire rubber granules, the sorption rate coefficient of second‐order kinetic equation was utilized indirectly to determine the rate‐limiting step. The diffusion coefficient lies in the scale of 10^?8 cm²/s, and the pore diffusion coefficient is in the range of 10^?9–10^?10 cm²/s. So both film and pore diffusion are rate limiting. Considering external mass transfer from fluid to particle, using the effect of initial concentration, and using the effect of adsorbent size, no conclusion was reached regarding rate‐controlling steps. It is apparent from the study that external mass transfer (film diffusion) as well as intra‐particle diffusion (pore diffusion) play significant roles in the sorption process for 2,4‐D removal from water onto rubber granules.     

基于变结构理论的中制导律设计方法研究

对于采用复合制导的空地导弹,中末制导交接班问题是影响命中概率的关键因素。针对这一问题,采用变结构理论设计中制导律。首先建立滑模面,保证滑模面上速度矢量与视线重合,且零化视线角速率,然后设计到达函数,使到达条件得到满足,可以保证交班时刻导弹可靠捕获目标,并为末制导提供最优初始条件。建立了导弹六自由度数学模型和目标捕获模型,进行全系统数字仿真,实验结果表明：在中末制导交接时刻,弹目视线与导弹速度矢量基本重合,误差为0.12°,视线角速度为-0.02°/s,在±20°视场下满足捕获需求,并且为末制导提供最优初始条件。该方法可以满足中末制导交接班要求,具有较强鲁棒性,且中制导段弹道平滑,需用过载小。     

基于MetropolisQ学习的蜂窝网络在线信道分配

针对现有的蜂窝网络的在线动态分配模型具有的信道需求量大、呼叫动态变化时阻塞率高和收敛速度慢的缺点,设计了一种基于MetropoisQ学习的蜂窝网络的在线信道分配方法。首先,在考虑同信道限制、邻居信道限制和同小区限制的基础上,设计了在线信道分配的数学模型,然后在Q-Learning算法基础上的设计了一种基于资格迹的Q(λ)算法实现信道的在线分配,为了进一步提高收敛速度,采用Metropois规则对算法中动作的选择方式进行改进,实现探索和利用的平衡。为了验证文中方法,采用Matlab工具上进行实验,仿真实验结果表明文中方法能实现蜂窝通信网络的在线信道分配,且与其它方法比较,具有较少的信道需求量、较低的阻塞率和收敛速度,较其它方法具有较大优越性。