加氢脱氮催化剂中硫化钼结构的表征

众所周知,重油加氢脱氮(HDN)所用Mo-Ni/Al2O3催化剂需经预硫化后始有显著的活性,关于硫化的条件工业上已较成熟,但在持续反应过程中硫化催化剂的结构与活性间的关系则很复杂,如硫化钼的价态和结构、金属组分和担体间的相互作用、反应条件及原料对催化剂组分的影响,以及硫化态催化剂中MoS2结晶的形貌等都可以引起催化剂活性本质的变化.     

聚烯烃（聚乙烯）低温热氧化与降解

综述了近年来聚烯烃特别是聚乙烯的低温热氧化机理，动力学以及氧化降解研究现状及发展，指出现今低温热氧化与降解研究意义。     

甲烷氧化偶联催化反应的特征

应用程序升温反应（ＴＰＲ）及质谱分析表征了ＣａＯ，Ｓｍ２Ｏ３，０．５－１０％Ｓｍ／ＣａＯ催化剂上的甲烷氧化偶联反应特性。谱图分析表明，在４００－１０００℃范围内，甲烷氧化偶联反应产物的变化呈现三个反应温度区域：（１）完全氧化区，反应主要为ＣＨ３·在催化剂表面完全氧化形成ＣＯｘ和Ｈ２：（２）偶联区，主要为ＣＨ３·的氧化和偶联竞争反应，Ｈ２谱线出现明显的低温峰；（３）氧耗尽区，反应为高温气相反应，产物     

DEHYDROGENATION AND AROMATIZATION OF METHANE IN THE ABSENCE OF OXYGEN OVER DOPED Mo/HZSM-5 CATALYSTS

研究了在Ｍｏ／ＨＺＳＭ－５催化剂上添加助剂以及不同的反应预处理温度对甲烷无氧脱氢芳构化反应的影响。实验结果表明，由于第二组分的添加，Ｍｏ／ＨＺＳＭ－５催化剂的活性和选择性都得到了较大程度的改善。预处理温度是影响催化剂反应性能的关键因素。Ｍｏ－Ｒｕ／ＨＺＳＭ－５催化剂经过８７３Ｋ空气预处理后，甲烷在９７３Ｋ的转化率约为１０％，催化剂的稳定性也得到较大程度的提高。ＴＰＳＲ实验结果表明，Ｒｕ的加入降低了芳烃生成的温度。ＴＰＯ和ＤＴＡ实验结果表明，在Ｍｏ－Ｒｕ／ＨＺＳＭ－５催化剂上可生成较多的碳物种，结合反应结果，可以认为反应过程中生成的碳物种对甲烷的无氧脱氢芳构化反应是起积极作用的     

GaPO4 high temperature crystal microbalance demonstration up to 720°C

Quartz-homeotypic gallium (ortho-) phosphate, GaPO₄, is of special interest for resonator applications asking for temperature compensated cuts with higher electro-mechanical coupling than quartz and operational temperatures up to 970°C. The crystal microbalance technique, well known for quartz (QCM) which can be used only at moderate temperatures, can now be extended to much higher temperatures using GaPO₄ crystals, benefiting from all three advantages mentioned above. Two different experiments were done to demonstrate the advantages of a crystal microbalance based on GaPO₄. First, the GaPO₄ resonator was used for film thickness determination and compared with a commercial QCM. This experiment demonstrated that the measuring range can be extended by using GaPO₄ resonators instead of quartz. The second experiment demonstrates the possibility for thermogravimetric analysis up to 720°C by using a new concept for resonator mounting.This revised version was published online in November 2005 with corrections to the Cover Date.     

高电导率的a—SiHY合金的低温电导特性

用射央求地在硅单晶衬底上沉积出电导率高达６０Ｓ／ｃｍ的ａ－ＳｉＨＹ合金薄膜。在２０－３００Ｋ，对于钇含量高的样品，其电导仍是热激活的。ｌｇσ与１／Ｔ的关系曲线能够被拟合成斜率不同的两条直线，直线的斜率和两直线间拐点所地 温度依赖于膜中钇的含量。但对钇含量低的薄膜，电导对温度的依赖关系度为σ∝ｅｘｐ（－１／Ｔ＾１／４）。结果表明，这些钇含量不同的样品在没的温度范围内具有不同的导电机制。     

Influence of molecular characteristics on overall isothermal melt-crystallization behavior and equilibrium melting temperature of syndiotactic polypropylene

Overall isothermal melt-crystallization and subsequent melting behavior of metallocene-catalyzed syndiotactic polypropylene resins of various molecular weights were investigated using differential scanning calorimetry (DSC) technique. Two sets of molecular weight range were synthesized with two different metallocene catalyst systems. The kinetics of the overall isothermal melt-crystallization process was analyzed based on various macrokinetic models, i.e. the Avrami, Malkin and Urbanovici-Segal models. The effective activation energy describing the overall isothermal crystallization process over the crystallization temperature range studied was estimated based on an Arrhenius approximation of the obtained Avrami crystallization rate constants. The equilibrium melting temperature for each of these resins was estimated based on the linear and non-linear Hoffman-Weeks extrapolative methods.     

Lu2O3对球形Ni(OH)2高温充放电性能的影响

为了改善镍电极的高温充电效率，采用机械混合的方式将球形Ni(OH)2与不同比例的Lu2O3混合后制成粘结式镍正极。充放电测试、循环伏安和XRD等实验结果表明，掺杂Lu2O3后镍电极的析氧过电位明显提高，高温充电效率得到了很大改善，在充电后的电极中β-NiOOH生成；而且Lu2O3的掺杂比例对镍电极的高温性能在不同的充放电倍率下有不同程度的影响，3．5％是最好的掺杂比例，掺杂对高温小电流充电效率的改善作用要大于高温大电流充电。     

Wärmekapazitätsmessungen Nach Scanning-Methoden Bis Zu Hohen Temperaturen

Scanning calorimetric methods permit determination of heat capacities at high temperatures up to 1600°C. For disk systems with power compensation application limits are in order of 700°C, and for cylindrical systems with electrical calibration up to 1000°C. For the high temperature range above 1000°C DSC plates and a cylindrical calorimetric systems based on the CALVET principle ('MULTI HTC’) are known. For cylindrical calorimetric systems the precision of the Cp data is between 2 and 5% even at high temperatures without any requirements on the kind and shape of samples. These results are better than data provided by DSC plate systems. This revised version was published online in July 2006 with corrections to the Cover Date.