A novel method for crack detection in beam-like structures by measurements of natural frequencies

A novel method is proposed for calculating the natural frequencies of a multiple cracked beam and detecting unknown number of multiple cracks from the measured natural frequencies. First, an explicit expression of the natural frequencies through crack parameters is derived as a modification of the Rayleigh quotient for the multiple cracked beams that differ from the earlier ones by including nonlinear terms with respect to crack severity. This expression provides a simple tool for calculating the natural frequencies of the beam with arbitrary number of cracks instead of solving the complicated characteristic equation. The obtained nonlinear expression for natural frequencies in combination with the so-called crack scanning method proposed recently by the authors allowed the development of a novel procedure for consistent identification of unknown amount of cracks in the beam with a limited number of measured natural frequencies. The developed theory has been illustrated and validated by both numerical and experimental results.     

Radiation effect on the optical and electrical properties of CdSe(In)/p-Si heteroj unction photovoltaic solar cells

The efficiency and radiation resistance of solar cells are graded.They are then fabricated in the form of n-CdeSe（In）/p-Si heterojunction cells by electron beam evaporation of a stoichiomteric mixture of CdSe and In to make a thin film on a p-Si single crystal wafer with a thickness of 100μm and a resistivity of～1.5Ω·cm at a temperature of 473 K.The short-circuit current density(j_sc),open-circuit voltage(V_oc),fill factor（ff） and conversion efficiency（η） under 100 mW/cm²（AMI） intensity,are 20 mA/cm²,0.49 V,0.71 and 6%respectively. The cells were exposed to different electron doses（electron beam accelerator of energy 1.5 MeV,and beam intensity 25 mA）.The cell performance parameters are measured and discussed before and after gamma and electron beam irradiation.     

DLTS characterization of defects in GaN induced by electron beam exposure

The deep level transient spectroscopy (DLTS) technique was used to investigate the effects of electron beam exposure (EBE) on n-GaN. A defect with activation energy of 0.12 eV and capture cross section of 8.0×10^–16 cm² was induced by the exposure. The defect was similar to defects induced by other irradiation techniques such as proton, electron, and gamma irradiation. In comparison to GaN, the EBE induced defects in other materials such as Si and SiC are similar to those induced by other irradiation methods.     

Application of electromagnetic processing for development of high-performance sintered powder metal parts

Electromagnetic processing was used to study the effects of electro-magneto forming on the dimensional control and thermal stability of sintered powder metal (PM) parts. The investigation was carried out on sinter-hardened, low chromium-molybdenum bainitic steel. The results show an increase in the microhardness of about 14% for the electromagnetic processed parts compared to the as-sintered parts. This was attributed to the 2% increase in the density, 17% and 29% reduction in the volume fraction of porosity and width of the bainitic lath, respectively, due to the electromagnetic processing. Dimensional characterization was carried out using a vertically aligned push-rod dilatometer. After four thermal cycles of heating and cooling, at a controlled rate of 5 °C/min to 1000 °C, the electromagnetic processed parts exhibited reduced dimensional change of about 44% lower than for the as-sintered parts. This is significantly important for applications that demand high dimensional tolerance and performance, especially at elevated temperatures.     

Some effects of foaming of the poly(butylene adipate‐co‐terephthalate) modified by electron radiation

Investigation of the effect of electron radiation and foaming agent on some properties of poly(butylene adipate‐co‐terephthalate) (PBAT) was the aim of the present paper. The mass flow rate, weight‐average molecular weight of irradiated PBAT as well as the morphological structure of foamed samples, their density, tensile strength, and specific strength were determined. It was found that irradiation of PBAT induces growth in weight‐average molecular weight and decrease in mass flow rate, and as a consequence of this increase in viscosity of this polymer. It was also found that foaming of irradiated PBAT causes formation of homogeneous cellular structure or structure with a clear separation of large and small cells. Simultaneously, the irradiated and foamed PBAT shows smaller density than that of non‐irradiated and foamed PBAT. Moreover, electron radiation does not influence tensile strength of the foamed PBAT; however, it increases its specific strength, although only if the content of foaming agent is 1 wt%.     

微水导激光切割玻璃的耦合装置设计

为了解决激光切割钢化玻璃过程中由于热应力导致产生裂纹并发生破裂的技术难题，建立了光液耦合模型，采用FLUENT软件进行了耦合腔内多场分析，获得了微水导激光切割钢化玻璃的工艺参量。结果表明，在喷口口径为0.4mm、水束压力为20MPa、激光功率为48W、切割速率为20mm/s的工艺条件下，厚度为0.5mm及1.0mm的玻璃试样的切割表面均比较光滑、基体内无微裂纹存在，切缝宽度约为100μm。该双注水口耦合装置的设计是合理的，能够满足钢化玻璃切割工艺的要求。     

Effects of multi-Schell beams on orbital angular momentum of entangled signal photons in low-order turbulence aberration channels

We model the detection and crosstalk probability of orbital angular momentum (OAM) states of the entangled signal photon in the Kolmogorov channels of the low-order turbulence aberrations and by the Rytov approximation. The results show that lower OAM mode number of signal photons and larger sub-beam number of multi-Gaussian Schell-model pump beam, the less susceptible of the detection probability of the signal photon to spatial coherence of source and turbulence aberrations is achieved. The maximum crosstalk probability is decrease as the decreasing of the sub-beam number of multi-Gaussian Schell-model. Enlarging OAM difference value or decreasing sub-beam number of multi-Gaussian Schell-model pump beam results in a lower crosstalk probability of the OAM of entangled signal photons.     

线型光束可燃气体探测器的校准

介绍线型光束可燃气体探测器的的校准方法。对线型光束可燃气体探测器的示值误差、报警功能、响应时间、光强衰减性能和抗日光干扰性能等主要计量特性及技术指标进行校准,给出了各主要计量特性的校准条件、试验设备和具体校准方法。对两台线型光束可燃气体探测器进行了校准,其示值误差用相对误差表示分别为–5%和4%,用引用误差表示分别为–4%FS和3%FS。经验证,上述结果均未超出设定指标,响应时间等其它主要计量特性也符合方法要求。该方法校准后的计量特性及技术指标较为合理,校准方法切实可行,可以用于线型光束可燃气体探测器的校准。     

Dispersion and localisation in structured Rayleigh beams

This paper brings a comparative analysis between dynamic models of couple-stress elastic materials and structured Rayleigh beams on a Winkler foundation. Although physical phenomena have different physical origins, the underlying equations appear to be similar, and hence mathematical models have a lot in common. In the present work, our main focus is on the analysis of dispersive waves, band-gaps and localised waveforms in structured Rayleigh beams. The Rayleigh beam theory includes the effects of rotational inertia which are neglected in the Euler–Bernoulli beam theory. This makes the approach applicable to higher frequency regimes. Special attention is given to waves in pre-stressed Rayleigh beams on elastic foundations.