双程放大技术在光纤放大器中的应用

双程放大技术是一种高效率、低成本的实用化放大技术。本文介绍了双程放大技术的优点及在各种放大器中的应用。     

基于片上DC-DC的CMOS光接收机前置放大器

利用CSMC 0.6μm CMOS工艺,设计了基于片上DC-DC转换器的光接收机前置放大器。电路采用可调跨阻放大器与片上DC-DC结构,有效地克服了单端跨阻放大器易受电源波动的干扰,并解决了高灵敏度与低失真相互矛盾的问题。模拟结果表明,输入动态范围为83 dB(峰-峰值=0.2μA~3 mA),等效输入电流噪声为1.2 pA/Hz(155 MHz),可稳定工作在155 Mb/s速率上;在5 V电源电压下,功耗为95 mW。     

供电器可供放大器最大级数的计算

有线电视电缆网采用供电器进行集中供电，要计算一个额定容量的供电器可供放大器的最大级数，算式是很复杂的，而用VisaulFOXPRO6．0编写一个小程序，利用电脑对上述问题进行处理，就变得简单易用。     

视频特技切换台的原理与功能

本文较系统、通俗地介绍了模拟视频特技切换台的矩阵输入、混合/效果放大器(M/E)、下游键、系统控制和同步发生器等电路单元,介绍了特技切换台的切换、混合、扫变、键控的基本原理和功能。     

磷酸盐激光玻璃非激活吸收系数测量研究

介绍了高功率激光放大器系统中磷酸盐激光玻璃的静态透过率测量。在正常运行条件下,4片长按布儒斯特角放置的国产N31钕玻璃片对1.054um的激光波长平均静态透过率为94.5%,介质的损耗系数为0.294%cm-1,平均非激活吸收系数为0.146%cm-1。在此基础上对片状放大器的增益系数的测量结果进行了修正,获得了5.25%cm-1的小信号增益系数。     

Broadband spectral shaping in a Ti:sapphire regenerative amplifier

A birefringent crystal quartz plate of known thickness has been used as a spectral filter for spectral shaping in a Ti:sapphire regenerative amplifier. The spectral profile of the amplified pulse ejected from the regenerative amplifier was observed while adjusting the birefringent crystal plate in the cavity. By altering the gain spectrum, the bandwidth of the regeneratively amplified pulse was increased from 18 to 35 nm by using a 0.34-mm thick birefringent plate. The output pulse spectrum from the regenerative amplifier neared the bandwidth of the seed pulse. As a comparison, we used a coated filter outside the regenerative amplifier cavity, and the bandwidth of the regeneratively amplified pulse was stretched to 28 nm. When the bandwidth was stretched to 35 nm, the pulse was compressed to 35 fs.     

相对论速调管放大器辐射频率可调性机理

 用场方法研究了相对论速调管放大器辐射频率的可调性。发现调制电流频率的可调性与一阶Bessel函数的周期相关，对应相同的一阶Bessel函数值，可以有多个不同数值的宗量，调制电流的频率与Bessel函数宗量数值包括中间腔与提取腔之间的距离和电子束的传输速度等因素相联系。理论估计的调制电流频率可调范围与实验测得的结果符合得很好。相对论速调管放大器辐射频率的可调性还取决于提取腔的设计。     

开关型霍尔传感器的原理与工程实现

介绍了开关型霍尔传感器的工作原理，设计了适用于工程测量的具体线路，并分析了该线路的特点。     

直接求线性规划可行基的一种方法

本文给出直接求线性规划问题基可行解的一种简易方法,该方法既避免了引入人工变量,减少存储,一般又能较快地得到一个较好的基可行解.     

10-GHz Optical Comb in L-Band Region With Brillouin/Erbium-Doped Fibre Laser

A multiwavelength Brillouin/erbium fibre laser (BEFL) which operates in the long wavelength (L-band) region is demonstrated for potential applications in an L-band wavelength division multiplexing (WDM) communication system. The laser configuration consists of a long erbium-doped fibre to enable L-band amplification where two 3-dB couplers take a portion of the generated BEFL signal and re-inject it into the single mode fibre to seed a cascaded BEFL line in the same direction as the first BEFL line. A stable and strong laser comb of up to five lines with 10-GHz spacing has been obtained with a Brillouin pump (BP) of 9.2 mW and a 980 nm pump of 92 mW. The BEFL has shown a broad tuning range with a tuning characteristic for line #1 which is flat over a range greater than 9.9 nm.