A simple polymer electrolyte membrane system for enrichment of low-level tritium (3H) in environmental water samples

Tritium (³H) is an essential tracer of the Earth's water cycle; yet widespread adoption of tritium in hydrologic studies remains a challenge because of analytical barriers to quantification and detection of ³H by electrolytic pre-concentration. Here, we propose a simple tritium electrolytic enrichment system based on the use of solid polymer electrolyte membranes (PEMs) that can be used to enrich ³H in 250–3000?mL environmental water samples to a 10-mL final volume. The IAEA PEM-³H system reported here can produce high enrichment factors (>70-fold) and, importantly, removes some of the deterrents to conventional ³H enrichments methods, including the use of toxic electrolysis and neutralization chemicals, spike standards, a complex electrolysis apparatus that requires extensive cooling and temperature controls, and improves precision by eliminating the need for tracking recovery gravimetrics. Preliminary results with varying operating conditions show ³H enrichments to 70-fold and higher are feasible, spanning a wide range of tritium activities from 5 to 150 TU with a precision of ～4.5?%. Further work is needed to quantify inter-sample memory and to establish lower ³H detection limits. The IAEA PEM-³H system is open source, with 3-D CAD and design files made freely available for adoption and improvement by others.     

Quantitative leak test for microholes and microtears in whole gloves and glove pieces

The current leak tests for gloves are qualitative. The developed quantitative leak test uses vacuum pressure to draw measured volumes of water to detect microholes/tears in whole gloves and glove pieces. A modified plastic vacuum desiccator interfaced with a Frazier air permeability tester allowed exposure of disposable unsupported/unlined/powderless Kimtech Blue nitrile to 50 mL of water for glove pieces or to 600 mL within a whole glove at vacua of 8–9 in. (20–23 cm) and 11–12 in. (28–30 cm) water gauge, respectively. Punctures of known dimensions were made before testing in specific glove areas using 21-, 22-, 26-, 30-, and 33-gauge needles (outer/inner diameters in micrometres of 873/514, 794/413, 635/311, 476/127, 318/159 and 238/133, respectively). The length of the punctures varied from 0.13 ± 0.01 to 0.80 ± 0.11 mm. Flow rates of water through the holes/tears ranged from 2.5 ± 0.4 to 106 ± 7 mL/min for glove pieces. For whole gloves, the ranges were from 31 ± 9 to 543 ± 110 mL/min in the palm area; and 0.23 ± 0.06 to 82 ± 18 mL/min in the finger/fingertip area. The method quantified tear lengths as short as 0.13 ± 0.01 mm.     

A Repaid Procedure for Preparing Oxyen-18 Determination in Water Samples

An equipment for the speed δ¹⁸O analysis of water samples is described. It used the equilibrium isotopic exchange reaction between water and CO₂ gas. Outgasing of samples through capillary without freezing down the samples, together with shaking during the equilibrium time, reduced considerably time for sample preparation.

Apparatus is air termostated with hand valves. Measured δ values are not very sensitive to precision of preparation work and reaction conditions, except of temperature. With good temperature control the standard reproducibility of single measurement is better than 0,1‰     

程控交换设备安装与维护教学内容的设计

实践教学是理论教学的有效补充，是专业技能的具体表现。在理论教学的基础上，结合现场工作的实际步骤，分析了程控交换设备的安装、业务开通及程控交换设备的维护三个业务情景的具体内容，最终使学习者掌握专业技能的具体流程和工作要点。     

真空冷却过程中实验条件对真空冷却速率的影响

以熟肉为实验材料,对实验条件对真空冷却速率的影响进行了理论分析和实验研究。实验结果表明:真空室有效容积越小、真空泵抽速越高,则真空冷却时间就会越短;冷阱温度对真空冷却速率有着明显的影响;当真空室内的最终压力在0.4～0.61kPa变化时,熟肉的表面温度一直在0℃以上,其真空冷却的时间随着真空室内压力的升高而增加。而真空室内的最终压力在0.3kPa左右时,熟肉的表面温度在真空冷却过程会低于0℃。     

基于LPC2378的天调匹配性能检测仪的设计及实现

为了解决生产中短波天调配谐过程存在的劳动强度大,统计不够准确等问题,设计了一种检测仪。该检测仪以嵌入式技术为基础,利用短波电台所提供的遥控命令,实现短波天调自动配谐功能,并根据统计得到的配谐数据判断天调匹配性能是否合格。经生产验证,该测试仪在提高劳动效率的同时,还能减少人工统计数据可能带来的误差。     

船载特种设备基点轨迹测量的误差分析

对船载特种设备基准点的空间位置进行测量,得到该基准点的运动轨迹并进行测量误差分析,是某项工程数据处理的重要内容.提出了利用三台船载GPS接收机测量船载特种设备基准点的原理和误差分析方法,介绍了该方法的误差源构成,依据测量原理模型,推导出定位精度的估算公式,并叙述了仿真计算与测量实施.     

Online induction heating for determination of isotope composition of woody stem water with laser spectrometry: a methods assessment

Application of stable isotopes of water to studies of plant–soil interactions often requires a substantial preparatory step of extracting water from samples without fractionating isotopes. Online heating is an emerging approach for this need, but is relatively untested and major questions of how to best deliver standards and assess interference by organics have not been evaluated. We examined these issues in our application of measuring woody stem xylem of sagebrush using a Picarro laser spectrometer with online induction heating. We determined (1) effects of cryogenic compared to induction-heating extraction, (2) effects of delivery of standards on filter media compared to on woody stem sections, and (3) spectral interference from organic compounds for these approaches (and developed a technique to do so). Our results suggest that matching sample and standard media improves accuracy, but that isotopic values differ with the extraction method in ways that are not due to spectral interference from organics.     

HL-2M 真空室保温层设计及安装

基于 HL-2M 真空室烘烤保温要求，通过有限元分析和原型件实验确定采用陶瓷纤维与纳米级微孔材 料组合作为 HL-2M 真空室保温材料。在 30℃时，保温层的导热系数小于 0.027W⋅m⁻¹·℃⁻¹；300℃时，导热系数 小于 0.038W⋅m⁻¹·℃⁻¹。在保温层厚度 25mm、热面温度 300℃且达到稳态时，冷面可控制在 85℃以下，线圈侧的 温度低于 60℃，整体热损失小于 12kW，满足 HL-2M 真空室烘烤需求。      

Vacuum Ultraviolet Spectrum of IBr

Rydberg transitions for the interhalogen IBr, are reported in the wavelength region 160-130 nm.