高压下聚苯胺的结构和电性能研究

 以金刚石压腔高压装置为工具，用Ⅱ型金刚石作压砧兼红外窗口，对本征态聚苯胺进行了高压（0~8.4 GPa）就位红外光谱测试。结果表明：在4.8~5.2 GPa压力区间，代表醌环振动的吸收峰相对代表苯环振动的吸收峰变小，表明聚苯胺在此压力区间结构上发生了显著变化，且这种变化是不可逆的。聚苯胺的高压（0~14.5 GPa）电阻测量结果表明：当压力小于7.5 GPa时，电阻随压力升高而显著降低，据此认为聚苯胺为电子性导电物质；在7.5 GPa处电阻出现极小值，然后又缓慢升高，至10 GPa后基本不变。推测聚苯胺电阻极小值是由结构变化引起的。至于红外光谱与电阻测量结果反映聚苯胺结构变化的压力值不一致，可能是由于测试条件不同所致。     

Electrical characterization of very-narrow-gap bulk HgCdTe single crystals by variable magnetic field hall measurements

Variable-magnetic-field Hall measurements (0 to 1.5 T) are performed on very-narrow-gap bulk-grown Hg_1−xCd_xTe single crystals (0.165 ≤ x ≤ 0.2) at various temperatures (10 to 300K). The electron densities and mobilities are obtained within the one-carrier (electrons) approximation of the reduced-con-ductivity-tensor scheme. The present data together with the selected data set reported by other workers exhibit a pronounced peak when the electron mobility is plotted against the alloy composition x-value which has been predicted to be due to the effective-mass minimum at the bandgap-crossing (E_g ≈ 0). The observed position (x ≈ 0.165), height (≈4 x 10² m²Vs), and width (≈0.01 in x) of the mobility-peak can be explained by a simple simulation involving only ionized-impurity scattering. A lower bound of the effective mass is introduced as a fitting parameter to be consistent with the finiteness of the observed electron mobility and is found to be of the order of 10⁻⁴ of the mass of a free electron.     

高功率飞秒脉冲激光器的进展

概述了超短激光脉冲技术发展的历程。详尽的论述了啁啾脉冲放大技术的原理和一些关键技术 ,并对当今飞秒激光器研究发展的状况进行了综述。在分析其应用前景的基础上 ,进一步指出了这一技术领域未来的发展趋势。结果表明 ,脉冲激光放大系统以后的发展方向是 :更短脉冲 ;追求更高峰值功率 ;连续光谱调谐化 ;向小型化乃至全光纤化发展。     

An 8-bit, 200 MSPS Folding and Interpolating ADC

An 8-bit, 200 MSPS folding and interpolating analog-to-digitalconverter, ADC, has been implemented in a 1.2 µmBiCMOS-process. It achieves 7.5 effective bits with a power dissipationof 575mW. The active area is 4mm². The implementationand measured results are presented. A simple analytical modelfor the interpolation-induced nonlinearity in a folding and interpolatingADC using sinusoidal folding is presented. The bowing of thereference ladder due to interaction with the input stages isanalyzed, and analytical models are derived.     

Theory of a novel voltage-sustaining layer for power devices

The theory of a novel voltage-sustaining layer for power devices, called a Composite Buffer layer (CB-layer for short) is proposed. The CB-layer can be implemented in several ways, one particular implementation is used here, which consists of alternating n- and p-type regions, that are parallel to the direction of the applied electric field. In the off-state, the fields induced by the depletion charges of both region types compensate each other to allowing the doping in both n-regions and p-regions to be very high without causing a reduction of the breakdown voltage. In the onstate the heavy doping ensures the voltage drop is very low and that the saturation current density high. A simple relationship between the specific on-resistance and R_on and the sustaining voltage V_B can be shown to be R_on=2.53 × 10⁻⁷bV_B^1.23 ωcm², where the breadth b (in μm) of each region is much smaller than the thickness W. The design method of the CB-layer is discussed in some detail. The simulation results are shown to be in perfect agreement with the theory. The structure has application to a wide variety of different power devices. An RMOST structure has been used to demonstrate the benefits of the technique in the paper, for which excellent performance is demonstrated.     

大功率CO_2激光器非平衡态合成WO_3／Fe_2O_3新型陶瓷催化剂──Ⅱ．WO_3／Fe_2O_3烯烃歧化反应催化剂的催化活性

用大功率ＣＯ２激光器熔制ＷＯ３／Ｆｅ２Ｏ３新型烯烃歧化反应催化剂。考查了催化剂组成、激光功率及熔炼时间与丙烯歧化反应催化活性之间的关系。     

高功率激光器的光束质量及其对激光加工的影响

本文介绍了光束的模式、评价光束质量的几种方法,着重介绍了国际标准化组织(ISO)提出的光束传输系数M作为评价光束质量的方法。文中还讨论了光束质量对焊接、切割加工的影响;热透镜效应对加工的影响等。     

高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

彩色PDP用玻璃基板

本文讨论了彩色ＰＤＰ现用钠钙玻璃的热稳定性，指出由于这种玻璃在热处理过程中易变形和收缩，因而不适合作大面积彩色ＰＤＰ基板材料，介绍了彩色ＰＤＰ基板玻璃的制造方法和特点。最后介绍了日本旭硝子公司和美国康宁公司各自为彩色ＰＤＰ新开发的玻璃基板材料ＰＤ２００和ＣＳ２５。     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007