Surface and interfacial properties of PVDF/acrylic copolymer blends before and after UV exposure

Morphological and chemical properties of both the surface and interface of poly(vinylidene fluoride)/poly(methyl methacrylate)-co-poly(ethyl acrylate) (PVDF/PMMA-co-PEA) blend films have been investigated before and after the samples were exposed to ultraviolet (UV) irradiation using a xenon arc lamp at 50 °C and 9% relative humidity (RH) for 7 months. Surface and interfacial morphologies were studied by atomic force microscopy (AFM). Chemical composition information was obtained by confocal Raman microscopy, attenuated total reflection-FTIR spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. Results show an enrichment of the PVDF material at the air surface, while the acrylic copolymer enriches the interface. Blends having greater than 50% mass fraction of PVDF show little change in the surface morphology after UV exposure for 7 months. However, for a lower PVDF content, blends exhibit significant degradation of PMMA-co-PEA copolymer and a much rougher surface after UV exposure. Microstructural changes in the PVDF spherulites are also observed after UV degradation. It is found that the surface and interfacial morphologies are correlated with the chemical properties.     

On the excitation of a closely spaced array by a line source

An infinite row of periodically spaced, identical rigid circularcylinders is excited by an acoustic line source which is parallelto the generators of the cylinders. A method for calculatingthe scattered field accurately and efficiently is presented.When the cylinders are sufficiently close together, Rayleigh–Blochsurface waves that propagate energy to infinity along the arrayare excited. An expression is derived which enables the amplitudesof these surface waves to be computed without requiring thesolution to the full scattering problem.     

Contact angle hysteresis of liquid drops as means to measure adhesive energy of zein on solid substrates

Adhesion of zein to solid substrates has been studied using surface energy profiles as indices and by adhesion mapping using atomic force microscopy (AFM). Different plasticizers like glycerol and sorbitol have been used to form mixed films with zein and properties of these films are studied using surface energy profiles. Comparison of the results from the different mixed samples with those from the pure zein films showed that force mapping could identify areas rich in protein. The adhesion maps produced were deconvoluted from sample topography and contrasted with the data obtained from contact angle measurements. A comparison of the two methods shows that the extent of contact angle hysteresis is indicative of both hydrophobicity of the surface as well as the force of adhesion. Mechanical properties and microstructure of zein films prepared by casting from solutions and using Langmuir-Blodgett film technique have been investigated. Pure zein seemed brittle and exhibited an essentially linear relationship between stress and strain. Films with plasticizer were tougher than these films. In general, mixed films showed better mechanical properties than pure films and had higher ultimate tensile strength and increased per cent elongation. Further, the mixed films of zein showed a higher force of adhesion compared to the pure films.     

Electron beam induced modification of poly(ethylene terephthalate) films

Electron beam processing of poly(ethylene terephthalate) (PET) films is found to promote significant changes in the melting heat, intrinsic viscosity and polymer film-liquid (water, isooctane and toluene) boundary surface tension. These properties are featured with several maximums depending on the absorbed dose and correlating with the modification of PET surface functionality. Studies using adsorption of acid-base indicators and IR-spectroscopy revealed that the increase of PET surface hydrophilicity is determined by the oxidation of methylene and methyne groups. Electron beam treatment of PET films on the surface of N-vinylpyrrolidone aqueous solution provided graft copolymerization with this comonomer at optimum process parameters (energy 700 keV, current 1 mA, absorbed dose 50 kGy).     

Effect of plasma treatment on interface property of BCN/GaN structure

Interface properties of BCN/GaN metal-insulator-semiconductor (MIS) structures are investigated by X-ray photoelectron spectroscopy (XPS) and capacitance versus voltage (C-V) characteristics measurements. The BCN/GaN samples are fabricated by in situ process consisting of plasma treatment and deposition of BCN film in the plasma-assisted chemical vapor deposition (PACVD) apparatus. XPS measurement shows that the oxide formation at the BCN/GaN interface is suppressed by nitrogen (N₂) and hydrogen (H₂) plasma treatment. The interface state density is estimated from C-V characteristics measured at 1 MHz using Terman method. The minimum interface state density appears from 0.2 to 0.7 eV below the conduction band edge of GaN. The minimum value of the interface state density is estimated to be 3.0 × 10¹⁰ eV⁻¹ cm⁻² for the BCN/GaN structure with mixed N₂ and H₂ plasma treatment for 25 min. Even after annealing at 430 °C for 10 min, the interface state density as low as 6.0 × 10¹⁰ eV⁻¹ cm⁻² is maintained.     

Surface polarity of cellulose derivates observed by coumarin 151 and 153 as solvatochromic and fluorochromic probes

Solvent‐dependent ultraviolet–visible (UV–vis) absorption and Stokes shifts including strong hydrogen‐bond‐donating (HBD) solvents such as 2,2,2‐trifluoroethanol and 1,1,1,3,3,3‐hexafluoro‐2‐propanol of two coumarine dyes (Co 151 and Co 153) were analyzed with multiple‐square analyses of linear solvation energy relationships and the Kamlet–Taft solvent parameter set to α (HBD capacity), β (hydrogen‐bond‐accepting capacity), and π* (dipolarity/polarizability). The UV–vis absorption and emission spectra of Co 151 and Co 153 were measured when adsorbed on various polysaccharides such as different cellulose batches, carboxymethylcelluloses with different degrees of substitution, and chitine. As a result of this evaluation, Co 153 is recommended as an alternative UV–vis probe for evaluating the dipolarity/polarizability of cellulose and cellulose derivates. Multiple adsorption of Co 153 on Linters cellulose took place indicating a wide‐surface polarity distribution, which makes the determination of a rigid polarity parameter questionable. Thus, fluorescence measurements of adsorbed Co 153 are suitable to detect inhomogenities on a surface but not for the determination of empirical polarity parameters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1210–1218, 2003     

Depth profile analysis of polyimide film treated by potassium hydroxide

The structural change in the depth direction of a polyimide (UPILEX‐S) film treated in alkaline solution, which was a representative surface treatment used to form a seed layer for plating and to improve the adhesive strength, was analyzed by means of micro Fourier transform infrared attenuated total reflection (FTIR‐ATR) line analysis with gradient shaving preparation. The polyimide film was treated with KOH. The imide ring opened through the alkaline treatment, and the amide structure and carboxylic acid salt were formed. The attainment depth of this structural change was almost proportional to the treatment time, and it reached about 8 μm after a 30‐min treatment. The degree of structural change through the alkaline treatment was almost constant after it reached a considerably degraded stage, and the chemically changed region penetrated into the inner part of the film from the surface. An intermediate layer before the final degraded stage appeared in the treated layer, and its thickness increased with the treatment time. The region that was changed chemically by the alkaline treatment progressed to the inner part simultaneously and continuously as the treatment time increased. The combined use of gradient shaving preparation and micro FTIR‐ATR line analysis was found to be extremely effective for the depth profiling of organic materials. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2071–2078, 2003     

Numerical calculations of temperature distribution of double layer metallic surface treated by laser beams

A mathematical model of laser beam treatment of double layer alloys (Ni/Fe, Al/Fe and Cr/Fe systems) describing the effect of laser beam on different physical and geometrical parameters of coated layer system has been adapted. The numerical solutions of the non-homogeneous heat-transport differential equation could estimate the temperature of the treated region.The suggested model allows investigation of the temperature distribution as a function of treated surface and laser parameters. The physical parameters of the treated materials were taken as functions of temperature due to the change in the temperature of the treated double layer materials.     

2‐connected 7‐coverings of 3‐connected graphs on surfaces

An m‐covering of a graph G is a spanning subgraph of G with maximum degree at most m. In this paper, we shall show that every 3‐connected graph on a surface with Euler genus k ≥ 2 with sufficiently large representativity has a 2‐connected 7‐covering with at most 6k ? 12 vertices of degree 7. We also construct, for every surface F² with Euler genus k ≥ 2, a 3‐connected graph G on F² with arbitrarily large representativity each of whose 2‐connected 7‐coverings contains at least 6k ? 12 vertices of degree 7. © 2003 Wiley Periodicals, Inc. J Graph Theory 43: 26–36, 2003     

Standardization of Methods for Characterizing the Surface Geometry of Solids

Since a comprehensive survey published in 1999 [1] much work was done in standardizing measuring methods to characterize the surface geometry of dispersed and/or porous solids and to certify reference materials. The present paper is an extension of a short communication [2]. It gives a survey on existing standards and reports on new drafts and proposals.