催化反应—导数示波极谱法测定痕量钨

在盐酸介质中，痕量钨对钛（Ⅲ）还原金莲花橙的缓慢反应有强烈催化作用，在ＮａＯＨ介质莲花橙Ｏ于－０．５０Ｖｖｓ．ＳＣＥ产生一灵敏的导数示波极谱波。据此，建立了一定检测限和测定范围分别为０．８ｎｇ／ｍＬ和１．６－８０ｍｇ／ｍＬＷ的催化反应－示波极谱新方法，用于钢和矿样中钨的测定，获得满意结果。     

氟化氢铵消解-电感耦合等离子体质谱(ICP-MS)法测定地球化学样品中的钨锡钼

建立了氟化氢铵消解地球化学样品,电感耦合等离子体质谱(IC P-M S)法测定样品中钨、锡和钼的方法.方法经过国家土壤和水系沉积物标准参考物质验证,方法的检出限钨为0.048μg/g、锡为0.079μg/g、钼为0.063μg/g,准确度(相对误差)钨为0.64％ ～6.28％、锡为0.29％ ～3.74％、钼为2.1...     

碳化钨-石墨烯插层复合物的制备及作为甲醇氧化助催化剂的性能研究

直接甲醇燃料电池(DMFCs)作为一种环境友好、高效的新能源,对解决世界目前面临的“能源危机”与“环境危机”这两大问题有着至关重要的意义,具有较广阔的应用前景.目前,甲醇氧化催化剂仍然以 Pt基为主,但是 Pt价格昂贵,且容易受甲醇氧化中间产物的毒化,从而影响了 DMFCs的商业化进程.碳化钨(WC)作为非贵金属催化剂,在催化方面具有类铂的性能.在 WC上负载适量的 Pt,可以通过两者的协同效应加强催化剂的抗 CO中毒能力.但是,由于 WC的导电性能不佳,比表面积较小,因此寻找合适的载体显得尤为必要.在碳载体中,石墨烯(RGO)具有优良的导电性以及独特的片层结构,是电催化剂的理想载体.以 RGO为载体, WC为插层物质制备的 WC-RGO插层复合物具有化学稳定性好、电导率高且电化学活性面积大等优势.但是,由于石墨烯表面光滑且呈惰性,同时使用传统的碳化方法制备的碳化钨颗粒较大,因此,制备较小颗粒且分散均匀的 WC-RGO插层复合物具有较大难度.一般以偏钨酸铵和氧化石墨烯(GO)为前驱体制备 WC-RGO插层复合物,但是由于偏钨酸根和 GO都带负电,因此不能成功地将偏钨酸根引入到石墨烯的片层结构中,造成 WC-RGO插层复合物组装上的困难.本文采用硫脲成功地合成了具有高分散性 WC纳米颗粒插层在少层 RGO里的 WC-RGO插层复合物.硫脲((NH2)2CS)作为阴离子接受器,具有较强的结合阴离子形成稳定复合物的能力,同时它也是合成具有片层结构的过渡金属硫化物的原料之一.因此在 WC-RGO插层复合物组装过程中,硫脲既作为锚定及诱导剂,又是制备片层二硫化钨(WS2)的硫源.材料具体制备方法如下：首先利用浸渍法,将偏钨酸根阴离子([H2W12O40]6?)牵引到(NH2)2CS改性过的 GO上形成[H2W12O40]6?-(NH2)2CS-GO前驱体;然后将前驱体放入管式炉中还原碳化,前驱体先反应生成 WS2;由于 WS2自身的2D片层结构,反应中可以得到 WS2-RGO插层复合物,接着原位碳化生成 WC-RGO插层复合物.碳化钨-石墨烯负载铂电催化剂(Pt/WC-RGO)通过微波辅助法制得,并采用 X射线衍射、扫描电子显微镜、透射电子显微镜及激光拉曼光谱等手段对其结构与形貌进行了表征.结果显示,在 WC-RGO插层复合物中, WC的平均粒径为1.5 nm, RGO的层数约为5层.在甲醇电氧化反应中,相比于商用 Pt/C催化剂, Pt/WC-RGO插层复合物催化剂具有更高的电化学活性面积(ECSA)和较高的峰电流密度(246.1 m2/g Pt,1364.7 mA/mg Pt),分别是 Pt/C的3.66和4.77倍.我们分别利用 CO溶出伏安法、计时电流法及加速耐久性试验法验证了 Pt/WC-RGO催化剂优秀的抗 CO中毒能力及稳定性. Pt/WC-RGO催化剂特殊的插层结构,在增加 WC与 Pt接触机会以加强协同作用的同时,促进了催化过程中质量及电荷的转移,因而具有比 Pt/C更高的催化活性.可见,通过制备WC-RGO插层复合物可降低 Pt用量,从而大大地降低燃料电池中电催化剂的成本.同时,我们使用的是一种高效,可大批量生产纳米材料的方法,有助于催化剂的商业化.     

不同载体对负载型氧化钨催化剂在己二酸合成反应中的结构及性能影响

以SBA-15、六角介孔二氧化硅（HMS）和SnO₂为载体,通过浸渍法合成了含钨负载型催化剂,并考察了三种催化剂在环氧环己烷选择氧化制备己二酸反应中的催化性能. 通过X射线衍射（XRD）,透射电镜/场发射透射电镜（TEM/FETEM）,紫外-可见漫反射光谱（UV-Vis DRS）,拉曼（Raman）光谱,X射线光电子能谱（XPS）以及傅里叶变换红外（FTIR）光谱等手段对各种催化剂的结构进行表征. 结果表明,载体与催化剂的性能有密切的关系. 以SnO₂为载体的WO₃/SnO₂催化剂活性最高,其次是WO₃/HMS催化剂,WO₃/SBA-15 催化剂的活性最差.XRD 分析显示WO₃/SnO₂催化剂中氧化钨物种的晶化程度最低,TEM 和XPS 结果表明氧化钨物种在WO₃/SnO₂催化剂表面高度分散并且粒径尺寸很小（约2 nm）,UV-Vis DRS结果表明在WO₃/SnO₂催化剂中存在孤立[WO₄]四面体和低聚态的钨物种,这些物种的存在可能是WO₃/SnO₂催化剂具有高活性的主要原因. 此外,WO₃/SnO₂催化剂可以重复使用多次,6 次反应后己二酸（AA）得率仍然保持在80%以上,说明氧化钨物种与SnO₂载体间存在强烈的相互作用,从而提高了催化剂的稳定性.     

石墨烯-氧化钨复合薄膜的制备及界面电子传输特性

以偏钨酸铵为钨源、聚乙烯吡咯烷酮为连接剂,采用浸渍提拉法制备了石墨烯-氧化钨复合薄膜,利用X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）及Raman光谱等方法对复合结构材料进行了表征,并利用光电流测试、交流阻抗谱（EIS）、瞬态光电流谱和强度调制光电流谱等方法,研究复合薄膜电极在光电作用下界面上的载流子转移过程和电荷传输行为. 结果表明,组成薄膜的氧化钨纳米颗粒与石墨烯充分复合,光电性能显著提高;与石墨烯复合后,薄膜的瞬态时间常数增大,电子-空穴对寿命延长;电子传输时间减少,为纯氧化钨薄膜的47.5%.     

Hollow fiber supported liquid membrane extraction for ultrasensitive determination of trace lead by portable tungsten coil electrothermal atomic absorption spectrometry

Hollow fiber supported liquid membrane extraction (HF-SLME) was used to separate and enrich trace lead from a large volume of 250 mL water sample to a final tiny volume of 30 μL of 1-octanol, 5 μL of which was inject into a tungsten coil electrothermal atomic absorption spectrometer (W-coil ET-AAS) for determination of lead. Some important parameters that influenced the extraction and determination were investigated in detail, such as the concentration of ammonium pyrrolidine dithiocarbamate (APDC), pH of sample solution, stirring rate, extraction time, pyrolysis current, atomization current, carrier gas flow rate, as well as interferences. Under the optimized conditions, a practical enrichment factor of 499 and a limit of detection (3σ) of 0.2 ng mL^{− 1} were obtained. The calibration curve was linear in the range of 0.5–10 ng mL^{− 1}. The relative standard deviation (RSD) was 5.6% for five measurements of a 4 ng mL^{− 1} lead standard solution. The accuracy of this method was examined by the analysis of certified reference water samples (GBW(E)080398 and GSBZ(E) 50009-88) for lead. Finally, the proposed method was applied to the determination of lead in local tap water, pond water and river water, with recoveries in the range of 96–109% for spiked samples.     

Surface diffusion of dysprosium on the W(1 1 1) facet

Diffusion of dysprosium on the (1 1 1) facet of a tungsten micromonocrystal was investigated by means of spectral analysis of field emission current fluctuations. The experimental spectral density functions of the current fluctuations were analysed by using Gesley and Swanson’s theoretical spectral density function, which enables to determine the surface diffusion coefficient D for dysprosium. Derived from the temperature dependence of D, the diffusion activation energy E is presented for some Dy coverages θ_(1 1 1). In the temperature range 400–600 K, the E first drops from 1.25 eV per atom at θ₍₁₁₁₎≈0.25 ML to 0.48 eV per atom at θ₍₁₁₁₎≈1 ML (corresponding to the minimum of the work function of the system), then increases to 1.03 eV per atom at θ₍₁₁₁₎≈1.3 ML. The results are discussed from the aspects of the substrate structure and interaction in the adsorbed layer.     

Synthesis and structural characterization of Ba(Ln2/3B1/3)O3 (Ln=Dy, Gd and Sm; B=Mo or W) complex perovskites

We describe in this work the synthesis and crystal structure of five rare earth and Mo(VI) or W(VI) containing complex perovskites. The compounds studied are Ba(Dy_2/3Mo_1/3)O₃, Ba(Dy_2/3W_1/3)O₃, Ba(Gd_2/3Mo_1/3)O₃, Ba(Gd_2/3W_1/3)O₃ and Ba(Sm_2/3W_1/3)O₃ and were prepared starting from solutions, by the polymeric precursors method. Structural characterization by HREM, SAED and powder XRD revealed the five compounds to be ordered cubic perovskites, SG Fm-3m (225), with a cell parameter double of that of a simple perovskite cell and increasing as the size of the trivalent lanthanide ion increases (Dy<Gd<Sm).     

蓝宝石火花塞

在如何提高火花塞的工作质量方面有多种方法,但是其中最重要的一个问题还没有得到解决,那就是火花塞工作的热学模型问题。理想的火花塞应该能在点火的瞬间被立刻加热,并且在接下来的电脉冲过程中迅速冷却,由此在热量的存储与散发之间取得平衡,以避免自点火。本文力图展示一种具有自动调节源于点火区域热流能力的火花塞,其技术的关键是顶部绝缘体材料,它是由蓝宝石单晶制作,而非传统的氧化铝陶瓷。     

Vibrational entropy-driven dealloying of Mo(1 0 0) and W(1 0 0) surface alloys

The formation and stability of Cu, Ag and Au-induced c(2 × 2) alloys at the Mo(1 0 0) and W(1 0 0) surfaces have been investigated with low-energy electron microscopy and diffraction. The ordered alloys transform to disordered overlayer structures at elevated temperature. Comparison of the transformation temperatures with energetics obtained from first principles calculations reveals the vibrational entropic contribution to the system free energy that defines alloy thermal stability. Effective Debye temperatures for metal adatoms are determined that exhibit the expected mass and bond strength dependence.