催化发光法同时测定空气中的甲醛、苯和二氧化硫

基于甲醛、苯和二氧化硫在纳米Ti3CeY2O11上的催化发光有交叉敏感现象,在3个波长处分别确定甲醛、苯和二氧化硫浓度与催化发光信号强度的响应关系,再依据发光信号强度的叠加性特征即可获取甲醛、苯和二氧化硫的准确浓度,据此建立了同时测定空气中甲醛、苯和二氧化硫的新方法.3个分析波长分别为420、535和680 nm,敏感材料表面温度为280℃,载气流速为130 mL/min.本方法对甲醛、苯和二氧化硫的检出限(3σ)分别为0.04、0.05和0.10 mg/m3,线性范围分别为0.08~75.60 mg/m3、0.10~101.40 mg/m3和0.30~115.00 mg/m3, 回收率分别为96.4%~103.7%、97.8%~102.5%和97.2%~103.3%.常见共存物,如乙醛、甲苯、硫化氢、氨、甲醇、乙醇和二氧化碳等不干扰测定.连续200 h通浓度均为50 mg/m3的甲醛、苯和二氧化硫混合气体,发光强度的相对偏差≤2%,表明此纳米级复合氧化物对甲醛、苯和二氧化硫的敏感性的寿命长.本方法充分利用了交叉敏感现象,可以实现空气中甲醛、苯和二氧化硫的在线分析.     

S掺杂的还原态TiO2-x的制备及其可见光催化性能

作为一种稳定、价廉的光催化剂,TiO2被广泛应用于各种污染物的降解;但是,较大的宽禁带(~3.2 eV)和较低的电子迁移率不仅使TiO2很难吸收可见光,而且光生电子和空穴的复合几率高,从而导致TiO2的总体光电效率不高.因此,设计能够被可见光激发、并具有快速光生电子传输的TiO2一直是研究热点.研究表明,Ti3+自掺杂的TiO2(还原态TiO2-x)不仅能够被可见光激发,而且使TiO2具有良好的电子导电性,从而有利于提高TiO2的光电转换效率.另外,非金属元素的掺杂能够减小TiO2的禁带宽度,使TiO2能够响应可见光并具有良好的可见光催化性能,其中S元素的掺杂被广泛研究.目前,S掺杂纳米TiO2的制备通常采用TiS2,单质S,硫脲、二甲亚砜等为S源,但这类原料通常价格昂贵或者具有一定的毒性,因而实际应用受到限制.而制备Ti3+自掺杂TiO2的方法大都是基于"还原法",在真空或强还原性气氛如H2,CO中加热TiO2,或采用高能粒子(电子、氩离子)轰击.在实际应用中,这些方法存在步骤多、条件苛刻、反应时间长和设备昂贵等不足.而且,还原法反应通常发生在颗粒的表面,形成的Ti3+很容易被空气和水中的溶解O2氧化,降低材料的稳定性.虽然在温和的液相中还原Ti4+可用于制备Ti3+掺杂的TiO2,但是由于反应过程中有副产物生成,需要进行后续处理才能得到纯的Ti3+自掺杂TiO2.因此,设计一种简单的制备S掺杂还原态TiO2-x光催化剂仍具有十分重要的意义.前期我们采用H2O2氧化TiH2得到不同状态的前驱体凝胶,然后进行不同方式的后处理得到Ti3+自掺杂的纳米TiO2.本文以TiH2和H2O2反应得到的黄色前驱体凝胶为Ti源,以价格低廉、无毒、稳定的二氧化硫脲为S源和还原剂,采用不同的方法制备了S掺杂的还原态TiO2-x光催化剂.本文初步研究了在凝胶中加入二氧化硫脲后进行水热处理,以及将干燥的凝胶粉末与二氧化硫脲混合热处理对所得产物的影响.并与纯的TiO2、还原态TiO2-x和S掺杂TiO2的光吸收、电化学、光催化性能进行对比研究.采用X射线衍射、透射电子显微镜、高分辨透射电子显微镜、X-射线光电子能谱、紫外-可见漫反射光谱、比表面分析和电化学工作站等技术对产物的结构、形貌和光电性能进行了表征.以罗丹明B(RhB)溶液为模拟废水,考察样品的可见光催化性能.结果表明,不同的后续处理方式不仅影响S掺杂TiO2-x的结晶性和形貌,而且影响产物的光吸收性能和电子传输性能,从而使不同条件下所得产物的可见光催化性能不同.其中,采用热处理方式得到的S掺杂TiO2-x样品在可见光下降解RhB的速率分别是纯的TiO2,TiO2-x和S掺杂TiO2的31,2.5和3.6倍,而且样品具有良好的循环稳定性.     

Thiophene-containing products of the Ugi reaction in an oxidation-triggered IMDA/aromatization cascade: a simple access to 3-oxoisoindolines

A novel approach to skeletally diverse 3-oxoisoindolines has been developed which includes preparation of Ugi adducts containing thiophene and fumaric acid residues. When treated with excess m-CPBA at room temperature, these precursors undergo a simple oxidative cycloaddition/aromatization transformation and the corresponding 3-oxoisoindoline products are isolated in fair chemical yield over two steps. The second step is thought to include S-oxidation/IMDA/S-oxidation/SO₂ extrusion/aromatization events.     

Binuclear cyclopentadienylcobalt sulfur and phosphinidene complexes Cp2Co2E2 (E = S, PX): Comparison with their Iron carbonyl analogues

Density functional theory studies on a series of Cp₂Co₂E₂ derivatives (E = S and PX; X = H, Cl, OH, OMe, NH₂, NMe₂) predict global minimum butterfly structures with one Co-Co bond for the “body” of the butterfly and four Co-E bonds at the edges of the “wings” of the butterfly. Tetrahedrane structures with both Co-Co and E-E bonds are higher in energy for Cp₂Co₂S₂ and Cp₂Co₂(PH)₂ and are not found in the other systems. This differs from the corresponding Fe₂(CO)₆S₂ and Fe₂(CO)₆(PX)₂ derivatives where tetrahedrane structures are predicted to be the lowest energy structures for all cases except X = NR₂ and OH and such a tetrahedrane structure is found experimentally for Fe₂(CO)₆S₂. The butterfly structures for the Cp₂Co₂E₂ derivatives are of two types. For Cp₂Co₂(PX)₂ (X = H, OH, OMe, NH₂, NMe₂) the lowest energy structures are unsymmetrical butterflies Cp₂Co₂(P)(PX₂) with two X groups on one phosphorus atom and a lone pair on the other (naked) phosphorus atom. Related low-energy unsymmetrical butterfly Fe₂(CO)₆(P)(PX₂) structures, not observed in previous theoretical studies, are now found for the corresponding Fe₂(CO)₆(PX)₂ derivatives. Symmetrical butterfly singlet diradical structures with one X group on each phosphorus atom in relative cis or trans positions are also found for the Cp₂Co₂(PX)₂ derivatives and are the global minima for Cp₂Co₂(PCl)₂ as well as Cp₂Co₂S₂. In all cases the cis structures are of lower energy than the corresponding trans structures. Rhombus structures having neither Co-Co nor E-E bonds are also found for all of the Cp₂Co₂(PX)₂ derivatives but always at higher energies than the butterfly structures, ranging from 17 to 29 kcal/mol above the global minima.     

Inhibiting effects of 2-mercapto-1-methylimidazole on copper corrosion in 0.5 M sulfuric acid

The inhibiting efficiency of 2-mercapto-1-methylimidazole (MMI) on copper corrosion in sulfuric acid was investigated at 30 °C. Its effectiveness was assessed through electrochemical impedance spectroscopy, potentiodynamic polarization and gravimetric measurements. The results of study reveal that the inhibition efficiency of MMI depends on its concentration and attains approximately 81% at 10^?4 M. The inhibitor was adsorbed on the copper surface according the Langmuir adsorption isotherm model. The value of standard free energy of adsorption was calculated from this isotherm.     

Study of the inhibition of the corrosion of copper and zinc in HNO3 solution by electrochemical technique and quantum chemical calculations

The corrosion inhibition of copper and zinc in 0.1 M HNO₃ by 1,2,3,4-tetrazole (TTZ) and some of its derivatives has been analysed in a comparative study. Two experimental techniques have been used such as weight-loss and electrochemical polarization measurements. The results obtained reveal that the addition of these compounds reduces preferentially the corrosion of Cu rather than that of Zn. The adsorption of tetrazolic compounds on a copper surface was more favourable than their adsorption on a zinc surface. Moreover the inhibition efficiency calculated for copper was found to attain 95% in the presence of 1-phenyl-5-mercapto-1,2,3,4-tetrazole (PMT) while it remains constant at 1% for all compounds tested using zinc as electrode. Relationship between molecular structure and their inhibition efficiency was elucidated by quantum chemical calculations using the density functional theory (DFT).     

基于随机共振和微纳传感器阵列的六氟化硫检测方法研究

建立了一种基于随机共振和微纳传感器阵列的六氟化硫气体检测方法.使用两个360 μm极间距离的微纳传感器构成的阵列结合随机共振算法,在室温常压,相对湿度70%的条件下检测3.0～24 g/m3 SF6气体及纯SF6气体,以信噪比极大值实现各浓度SF6气体的区分.传感器工作于微电离平衡状态,检测过程中无有害气体产生,安全性较高.为检验该方法的实用性,依据国家标准在温度20 ℃、相对湿度70%和常压条件下模拟现场检测3.0～12 g/m3SF6气体,结果表明: 本方法具有较好的重复性和实用性.     

Activation of free-radical polyfluoroalkylation of organic substrates with freon BrCF2CF2Br using a system of organic base-electron transfer mediator

A polyfluoroalkylation of pyrrole and phenols with freon BrCF₂CF₂Br using sulfur dioxide-substituted pyridine activating system proceeds at the aromatic nucleus by a free-radical mechanism. The essential influence of the basicity of the medium is demonstrated and discussed.     

新型咪唑啉化合物在H_2S/CO_2共存条件下对Q235钢的缓蚀性能

合成了一种新型咪唑啉化合物1-(2-氨基-硫脲乙基)-2-十五烷基-咪唑啉(IM-S),并通过失重法、电化学方法及扫描电镜等研究了IM-S在H2S/CO2共存条件下对Q235钢的缓蚀性能,探讨了其在Q235钢表面的吸附行为.结果显示,IM-S具有较好的抗H2S、CO2腐蚀能力,能同时抑制碳钢腐蚀的阴、阳极反应过程,最高缓蚀效率可达92.74%.缓蚀剂在Q235钢表面呈单分子层吸附,属于以化学吸附为主的混合吸附.最后采用量子化学方法对IM-S的缓蚀机理做了进一步分析.     

超重力场电沉积NiW合金及其耐碱腐蚀性能

在超重力条件下电沉积NiW合金镀层,考察了超重力对NiW合金电沉积过程(各元素分电流、W含量和槽电压等)的影响规律;并利用扫描电子显微镜(SEM)、Tafel技术和电化学阻抗谱(EIS)技术研究了电沉积NiW合金镀层的表面形貌和在NaOH溶液中的抗腐蚀性能,同时通过浸泡实验考察了镀层的稳定性.结果发现,与常重力条件电沉积的NiW合金相比,超重力场电沉积的NiW合金中W含量增加,镀层表面无微裂纹产生;在10%(w)NaOH溶液中镀层自腐蚀电位正移,自腐蚀电流密度减小,腐蚀电阻也由常重力(重力系数G=1)时的865Ω·cm2增大至超重力(G=256)时的2305Ω·cm2;在10%NaOH溶液中浸泡144h后,超重力场电沉积的NiW合金表面无破碎和起皮现象发生.超重力技术在NiW合金电沉积过程中的应用,使镀层的耐碱腐蚀性能得到改善.