Optimization of inoculum to substrate ratio for enhanced methane yield from leather fleshings in a batch study

One of the most significant issues of the last few decades has been tracing for renewable energy sources. Animal fleshing (ANFL) is the most common proteinaceous solid waste accured during the production of leather and it must be disposed of in an environmentally responsible manner. This paper is attempts to assess the biogas production from solid waste originating from the chrome based tannery. Anaerobic digestion of these wastes will be a viable option for waste stabilization and energy production in the form of biogas to be utilized in the industry. The bio-methane potential of the wastes were examined by mixing these wastes with various sources of inoculum and different inoculum to substrate (I/S) ratio considered. The batch experiments were carried out in 2.5 l glass reactors with a various source of inoculumviz., Cow Dung (CD), Elephant Dung (ED) and Bio-Digested Slurry (BDS) with varied inoculum to substrate (LFs) ratios for a retention time of 50 days with replications. The results obtained from the experiments showed that BDS:LF (25:75) had the highest gas production of 14505 ml (651.85 ml CH₄g^?1 VS) followed by CD:LF (50:50) produced 12072.5 ml (789.36 ml CH₄g^?1 VS) and ED:LF (75:25) produced 11252.5 ml (1492.08 ml CH₄g^?1 VS)with a methane content of 63.77, 61.92 and 62.72%, respectively.     

Nucleation and growth of copper on glassy carbon: Studies in extended overpotential interval

The nucleation and growth of copper crystals on a glassy carbon electrode are investigated at different constant overpotentials. Current transients are recorded and the number of copper nuclei is microscopically registered. The experimental data for the growth current are interpreted according to the theories of progressive and instantaneous nucleation and information is obtained on the stationary nucleation rate, the saturation nucleus number density and the exchange current density at the crystals–solution interface boundary.     

Concerted cycloaddition of chlorosulfonyl isocyanate to α-pinene stepwise rearrangement of the β-lactam cycloadduct to a γ-lactam

Chlorosulfonyl isocyanate adds to α-pinene in concerted fashion to give the unrearranged N-chlorosulfonyl-β-lactam 2 (75%). Thermolysis of cycloadduct 2 affords the rearranged N-chlorosulfonyl-γ-lactam 6 (60%) via a sequence of transient carbonium ions (45). Reductive hydrolysis of 2 and 6 gave, respectively, the NH-β-lactam 3 (70%) and the NH-γ-lactam 7 (70%). Proof of structure of the rearranged γ-lactams 6 and 7 are provided, respectively, by X-ray crystallographic analysis and the application of the Eu(dpm)₃ NMR shift reagent.     

Molecular modeling of cytochrome P450 3A4

The three-dimensional structure of human cytochrome P450 3A4 was modeled based on crystallographic coordinates of four bacterial P450s: P450 BM-3, P450cam, P450terp, and P450eryF. The P450 3A4 sequence was aligned to those of the known proteins using a structure-based alignment of P450 BM-3, P450cam, P450terp, and P450eryF. The coordinates of the model were then calculated using a consensus strategy, and the final structure was optimized in the presence of water. The P450 3A4 model resembles P450 BM-3 the most, but the B helix is similar to that of P450eryF, which leads to an enlarged active site when compared with P450 BM-3, P450cam, and P450terp. The 3A4 residues equivalent to known substrate contact residues of the bacterial proteins and key residues of rat P450 2B1 are located in the active site or the substrate access channel. Docking of progesterone into the P450 3A4 model demonstrated that the substrate bound in a 6-orientation can interact with a number of active site residues, such as 114, 119, 301, 304, 305, 309, 370, 373, and 479, through hydrophobic interactions. The active site of the enzyme can also accommodate erythromycin, which, in addition to the residues listed for progesterone, also contacts residues 101, 104, 105, 214, 215, 217, 218, 374, and 478. The majority of 3A4 residues which interact with progesterone and/or erythromycin possess their equivalents in key residues of P450 2B enzymes, except for residues 297, 480 and 482, which do not contact either substrate in P450 3A4. The results from docking of progesterone and erythromycin into the enzyme model make it possible to pinpoint residues which may be important for 3A4 function and to target them for site-directed mutagenesis.     

Advanced Current Collectors for Alkali Metal Anodes

High-energy-density batteries are in urgent need to solve the ever-increasing energy storage demand for portable electronic devices, electric vehicles, and renewable solar and wind energy systems. Alkali metals, typically lithium(Li), sodium(Na) and potassium(K), are considered as the promising anode materials owing to their low electrochemical potential, low density, and high theoretical gravimetric capacities. However, the problem of dendrite growth of alkali metals during their plating/stripping process will lead to low Coulombic efficiencies, a short lifespan and huge volume expansion, eventually hindering their practical commercialization. To resolve this issue, a very effective approach is engineering the anodes on structured current collectors. This review summarizes the development of the alkali metal batteries and discusses the recent advances in rational design of anode current collectors. First, the challenges and strategies of suppressing alkali-metal dendrite growth are presented. Then the special attention is paid to the novel current collector design for dendrite-free alkali metal anodes. Finally, we give conclusions and perspective on the current challenges and future research directions toward advanced anode current collectors for alkali metal batteries.     

Anodic behavior of nickel-based alloys in the electrolytic production of NF3

The Ni-based alloys, such as Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si, prepared by hot isostatic pressing (HIP) at 1000 °C under 2 × 10⁸ Pa for 2 h were employed as the anodes for electrolytic production of NF₃. The current efficiencies for NF₃ formation were 42-38, 52-40, 52-47, 63-62, 50 and 41% for Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloys, respectively. The current efficiencies only on Ni-Cu alloys with Cu concentrations lower than 10 mol% were almost the same as those on Ni sheet and HIPed Ni anodes, whereas those on the other alloys used in this study were smaller compared with those on both Ni anodes. On the other hand, the current losses caused by anodic dissolution of Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloy electrodes were 7.95-4.42, 6.40-7.02, 5.60-6.30, 3.34-6.33, 5.10 and 0.18%, respectively. The anode consumptions of Ni-5 mol% Cu and Ni-5 mol% Si alloys were almost the same or smaller compared with those of Ni sheet and HIPed Ni electrodes, though those of other alloys used were large compared with those of both Ni anodes. Consequently, addition of Cu to the nickel matrix is available for a cheaper cost of anode with keeping a same current efficiency as that on the Ni anode and addition of Si to the nickel matrix is effective for decreasing anode consumption largely. A Ni sheet electrode containing a trace of impurities, such as Co, Mn, Ag and Al, is also favorable as the anode for electrolytic production of NF₃.     

Traps centers and deep defects contribution in current instabilities for AlGaN/GaN HEMT's on silicon and sapphire substrates

AlGaN/GaN high electron mobility transistors (HEMTs) with Si and Al₂O₃ substrates reveals anomalies on I_ds-V_ds-T and I_gs-V_gs-T characteristics (degradation in drain current, kink effect, barrier height fluctuations, etc.). Stress and random telegraph signal (RTS) measurements prove the presence of trap centers responsible for drain current degradation. An explanation of the trapping mechanism responsible for current instabilities is proposed. Deep defects analysis performed by capacitance transient spectroscopy (C-DLTS), frequency dispersion of the output conductance (G_ds(f)), respectively, on gate/source and drain/source contacts and RTS prove the presence of deep defects localized, respectively, in the gate and in the channel regions. Defects detected by C-DLTS and G_ds(f) are strongly correlated, respectively, to barrier height inhomogeneities and kink anomalies. Gate current analysis confirms the presence of (G-R) centers acting like traps at the interface GaN/AlGaN. Finally, the localization of these traps defects is proposed.     

Accuracy and CPU time of JE-TLM,PLRC-TLM and CRC-TLM methods for plasma medium

The current density (JE), the piecewise linear recursive convolution (PLRC) and the constant convolution recursive (CRC) techniques are developed and integrated into the transmission line matrix (TLM) algorithm. A comparison of these three schemes according to the criteria of accuracy and CPU time is presented. Numerical experiments show that JE provides the most accurate solution and requires the least CPU time; PLRC is nearly as accurate but consumes more CPU time than CRC.     

Simultaneous extraction of source and drain resistances in top contact organic thin film transistors from a single test structure

A method of extraction of source and drain resistances in linear mode of operation from a single transistor is described. The proposed method can also be used to measure source resistance over the entire operating range from linear to saturation mode of operation. The method uses two floating probes outside the channel, one adjacent to the source and the other to the drain to sense the voltage under these contacts. Using transmission line analysis, the source and drain resistances are directly extracted from these measurements. 2D numerical simulation results confirm the validity of the proposed technique and sensitivity analysis shows that the method is more accurate than the conventional gated four probe technique, especially, when the source resistance is much smaller than the channel resistance. Experimental results obtained with Pentacene top-contact transistors are used to illustrate the proposed technique. Analysis of two devices with very different source resistance is carried out to highlight the ability of the proposed technique to offer insight into the different contributing factors. Current crowding under the source contact and accurate estimation of mobility without the distorting effects of source resistance are also described.     

In situ vapor-deposited parylene substrates for ultra-thin,lightweight organic solar cells

We fabricate the thinnest (1.3 μm) and lightest (3.6 g/m²) solar cells yet demonstrated, with weight-specific power exceeding 6 W/g, in order to illustrate the lower limits of substrate thickness and materials use achievable with a new processing paradigm. Our fabrication process uniquely starts with growth of an ultra-thin flexible polymer substrate in vacuum, followed by deposition of electrodes and photoactive layers in situ. With this process sequence, the entire cell—from transparent substrate to active layers to encapsulation—can be fabricated at room temperature without solvents and without breaking vacuum, avoiding exposure to dust and other contaminants, and minimizing damage risk associated with handling of thin substrates. We use in situ vapor-phase growth of smooth, transparent, and flexible parylene-C films to produce ultra-thin, lightweight molecular organic solar cells as thin as 2.3 μm including encapsulation with a second parylene-C film. These parylene-based devices exhibit power conversion efficiencies and fabrication yields comparable to glass-based cells. Flexible solar cells on parylene membranes can be seamlessly adhered to a variety of solid surfaces to provide additive solar power.