Phase relations in the system ln-CulnS2

By DTA and x-ray diffraction the phase relations in the pseudobinary system In-CuInS₂ have been investigated. CuInS₂ hs a melting point of 1090° C and within this system there is a broad region of liquid immiscibility. A four phase invariant reaction exists at 633° C which is of the form: L₂ = L₁+ CuInS₂ + InS.     

一种可用于可调谐环行Ti：Al_2O_3激光器的宽带单向器

本文介绍一种宽带单向器的原理及设计。选用ＴＧＧ作磁旋光介质，旋光石英晶片作补偿片，所设计的色散补偿型宽带单向器预计可在７００～１０００ｎｍ波长范围内实现环行激光腔中的单向行波运行；将其应用在可调谐环行Ｔｉ：Ａｌ２Ｏ３激光器中，获得了良好的实验结果。     

Film morphology and reaction rate for the CVD of tungsten by the WF6—SiH4 reaction

Journal of Electronic Materials - Low pressure chemical vapor deposition (LPCVD) of tungsten (W) by SiH4 reduction of WF6 on Si(100) surfaces was studied in a single-wafer, cold-wall reactor over a...     

激光光束质量因子的研究进展

本文详细分析了各种光场下光束质量M2因子。在不同的场中,A.E.Siegman当初所定义的M2因子,已经有了很大的变化,因而M2因子的特性也与当初不同,不仅M2因子可以大于等于1,而且可以小于1,甚至小于0。其反映的物理意义,也从经典场中的衍射极限倍数,变化为非经典场中的准直性量度以及对空间相干性的某些反映。此外还列举并分析了几种特殊的光束质量因子,最后讨论了M2因子应用的问题并指出了其局限性。     

Synthesis and nuclear magnetic resonance analysis of starch‐g‐poly(1,4‐dioxan‐2‐one) copolymers

A new biodegradable starch graft copolymer, starch‐g‐poly(1,4‐dioxan‐2‐one), was synthesized through the ring‐opening graft polymerization of 1,4‐dioxan‐2‐one onto a starch backbone. The grafting reactions were conducted with various 1,4‐dioxan‐2‐one/starch feed ratios to obtain starch‐g‐poly(1,4‐dioxan‐2‐one) copolymers with various poly(1,4‐dioxan‐2‐one) graft structures. The microstructure of starch‐g‐poly(1,4‐dioxan‐2‐one) was characterized in detail with one‐ and two‐dimensional NMR spectroscopy. The effect of the feed composition on the resulting microstructure of starch‐g‐poly(1,4‐dioxan‐2‐one) was investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3417–3422, 2004     

TFT有源矩阵α－Si∶H薄膜PECVD淀积工艺研究

分析了α－Ｓｉ∶Ｈ薄膜的质量和厚度对α－Ｓｉ∶ＨＴＦＴ关键性指标的影响，深入、详细地讨论了其ＰＥＣＶＤ淀积工艺，并在实验的基础上确定了最佳淀积工艺参数，从而获得了高性能的７５ｍｍ３７２×２７６像素α－Ｓｉ∶ＨＴＦＴ有源矩阵     

提高E^2PROM中NMOS管源漏穿通电压的实验研究

为了提高Ｅ＾２ＰＲＯＭ中Ｎ管源漏穿通电压，用实验的方法对制造工艺进行了研究。结果表明，高能量注入是提高ＶＰＴ的有效手段，但受到ｐｎ结击穿的限制，只适用于低区短沟Ｎ管；ＤＤＤ工艺大幅度高ＶＰＴ，但ｐｎ结击穿电压低于２０Ｖ，不能应用于高压ＭＯＳ管；采用适量的防穿通注入和适当增大沟道长度为最理想的工艺途径。     

Accurate measurement of capture cross sections in deep level transient spectroscopy: Application to EL2 in GaAs

A rigorous formulation of capacitance changes during trap filling processes is presented and used to accurately determine the electron capture cross section of EL2 in GaAs at a particular temperature, 377K, in this case. The value, σ_n (377K) = 2.7 × 10⁻¹⁶ cm², is compared with that predicted from the emission dependence.     

Effect of site-selective substitution in bulk superconducting Tl2Ba2CaCu2O8

Magnetization measurements were carried out on bulk Tl₂Ba₂CaCu₂O₈ (referred to as Tl-2212) and on various site-selective substituted Tl-2212 samples. At 5K between 0 and 4.5 T, the 5 at. % Mg-doped Tl-2212 (Tl,Mg-2212) samples displayed enhanced pinning as demonstrated by a field dependent increase of the magnetic critical-current density J_c by 18 to 25 percent over that of pristine Tl-2212. Excess Mg (10–15 at. %), however, is deleterious. Rietveld refinement of the x-ray diffraction pattern showed Mg on the Tl sites. Auger electron spectroscopy analysis showed part of the Mg on grain boundaries. The flux-creep activation energies are higher for flux expulsion than for flux penetration in both Tl-2212 and Tl,Mg-2212 samples; the latter displays higher individual values. Our results demonstrate an increase in the number density of flux lines as a result of increased density of atomic-size-structural, defects by Mg (5 at. %) doping. In the Tl_2−yBa₂(Ca_1−zY_z)Cu₂O_8−x(z=0–0.3; single phase; x and y represent oxygen and thallium vacancies) system also studied, the T_c decreases as z increases. At z=0.3, the sample becomes an antiferromagnetic semiconductor.     

Fluorinated,crosslinkable terpolymers based on vinylidene fluoride and bearing sulfonic acid side groups for fuel‐cell membranes

The radical terpolymerization of 8‐bromo‐1H,1H,2H‐perfluorooct‐1‐ene with vinylidene fluoride (VDF) and perfluoro(4‐methyl‐3,6‐dioxaoct‐7‐ene) sulfonyl fluoride is presented. Changing the feed compositions of these three fluorinated comonomers enabled us to obtain different random‐type poly[vinylidene fluoride‐ter‐perfluoro(4‐methyl‐3,6‐dioxaoct‐7‐ene) sulfonyl fluoride‐ter‐8‐bromo‐1H,1H,2H‐perfluorooct‐1‐ene] terpolymers containing various sulfonyl fluoride and brominated side groups. Yields higher than 70% were reached in all cases. The hydrolysis of the sulfonyl fluoride group into the ? SO₃Li function in the presence of lithium carbonate was quantitatively achieved without the content of VDF being affected, and so dehydrofluorination of the VDF base unit was avoided. These original terpolymers were then crosslinked via dangling bromine atoms in the presence of a peroxide/triallyl isocyanurate system, which produced films insoluble in organic solvents such as acetone and dimethylformamide (which totally dissolved uncured terpolymers). The acidification of ? SO₃Li into the ? SO₃H function enabled protonic membranes to be obtained. The thermal stabilities of the crosslinked materials were higher than those of the uncured terpolymers, and their electrochemical performances were investigated. According to the contents of the sulfonic acid side functions, the ion‐exchange capacities ranged from 0.6 to 1.5 mequiv of H⁺/g, whereas the water uptake and conductivities ranged from 5–26% (±11%) and from 0.5 to 6.0 mS/cm, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4566–4578, 2006