Epoxy based coatings on glass: strengthening mechanisms

Glass may be strengthened by epoxy coatings although the strengthening mechanisms remain unclear. Possible strengthening mechanisms are reviewed and are used to analyse strength data for both a solvent based and a water based coating system. The coatings either fill (solvent based coatings), or partially fill (water based coatings) surface cracks and it is shown that closure stresses arising from the thermal expansion mismatch of the coating within these cracks can account for the observed degrees of strengthening. It is also demonstrated that other suggested mechanisms such as flaw healing cannot fully account for the observed degree of strengthening.     

Weighted oscillator strengths and lifetimes for the S IX and S X spectra

The weighted oscillator strengths (gf) and the lifetimes presented in this work were carried out in a multi configuration Hartree-Fock relativistic (HFR) approach. In this calculation, the electrostatic parameters were optimized by a least-squares procedure, in order to improve the adjustment to experimental energy levels. This method produces gf-values that are in better agreement with intensity observations and lifetime values that are closer to the experimental ones. In this work, we presented all the experimentally known electric dipole S IX and S X spectral lines.     

Crack path instabilities in DCDC experiments in the low speed regime

We studied the low speed fracture regime (10⁻⁴-10⁻⁹ m s⁻¹) in different glassy materials (soda-lime glass, glass ceramics) with variable but controlled length scale of heterogeneity. The chosen mechanical system enabled us to work in pure mode I (tensile) and at a fixed load on double cleavage drilled compression specimen. The internal residual stresses of studied samples were carefully relaxed by appropriate thermal treatment. By means of optical and atomic force microscopy techniques fracture surfaces have been examined. We have shown for the first time that the crack front line underwent an out-of-plane oscillating behavior as a result of a reproducible sequence of instabilities. The wavelength of such a phenomenon is in the micrometer range and its amplitude in the nanometer range. These features were observed for different glassy materials providing that a typical length scale characterizing internal heterogeneities was lower than a threshold limit estimated to few nanometers. This effect is the first clear experimental evidence of crack path instabilities in the low speed regime in a uniaxial loading experiment. This phenomenon has been interpreted by referring to the stability criterion for a straight crack propagation as presented by Adda-Bedia et al. [Phys. Rev. Lett. 76 (1996) 1497].     

达县广电城域网运行状况及故障分析

对达县广电城域网运行状况进行了检测，认为不能满足用户上网需要的原因除了网内病毒感染之外，设备与设备之间链路层协商及连接线出现故障。改进措施主要有两点：解决NE08E与S8505的连接问题，解决S8505上的DHCP服务器不能分配IP地址问题。     

AT91SAM7S64芯片I2C(TWI)接口应用开发

较为详细地介绍AT91SAM7S64芯片的I2C接口控制器中外围数据控制器(PDC)的使用方式,并将其与AT24C04之间的通信作为实例给出完整的应用开发流程和软硬件详细描述。该方法的可行性已经为工程实践和实际产品所证实。该操作也可推广到其他AT91SAM7S系列ARM处理器与其他I2C接口器件间的通信。并对其他拥有外围数据控制器的接口开发有一定的借鉴意义。     

一种简单的S参数去嵌入技术

介绍了在低成本夹具上，任意微带结构二端口网络S参数去嵌入的方法；该方法用于获取放大器模块的S参数，根据这些参数设计的C波段的放大器实测结果与仿真一致。     

$M$-半群的直觉$(S,T)$-模糊$M$-子半群的性质

K.T.Atanassov在1986年首先引入直觉模糊集的概念,本文利用s-范数和t-范数,引入M-半群的直觉(S,T)-模糊M-子半群的概念,刻画其性质和特征,我们再进一步给出了直觉(S,T)-直积的概念,并由此探讨了一些有意义的相关结论。     

轴端沟槽底部激光强化工艺参数优化研究

分析了选用不同激光能量密度对HT300进行表面强化处理时，材料表面呈现的四种状况；未相变硬化、相变硬化、表面微熔与表面熔凝的金相组织。根据工艺要求，选取相变硬化方法对轴端沟槽底表面进行处理。分析了工件激光处理方法并通过试验研究，寻找轴端沟槽底部激光强化工艺参数；激光功率（P）、光斑直径（D）及扫描速度（V）的优化组合。硬度测试及耐磨性能试验表明：激光相变处理和激光熔凝处理后轴端沟槽底部表面较表面感应淬火硬度分别提高7%和34%，绝对磨损体积分别下降了13%和25%。实践证实，对轴端沟槽底部激光相变硬化处理方法较其他表面处理方法工艺简单，加工工件符合技术要求，试验结果对零件表面处理提供了可靠依据。     

On bimeasurings II

We answer some questions posed in [L. Grunenfelder, M. Mastnak, On bimeasurings, J. Pure Appl. Algebra 204 (2006) 258-269] concerning the universal bimeasuring bialgebra via a construction of suitable subcoalgebras of the universal measuring coalgebra.