基于WUSB的RFID系统后台数据管理系统接口的设计

在RFID(射频识别)系统的阅读器和后台数据管理系统之间引进一种新的连接方法———无线连接,可以突破有线连接的限制。基于WUSB(W ireless USB)的无线连接方案传输距离适中、成本低、功耗低、开发简单、系统稳定,是目前较适合RFID系统的解决方案。同时提供详细、完整的实施方案,包含设计方法、数据流程和设计实例,并对有关芯片进行了描述。     

高速系统PCB设计中的几个关键问题

随着微电子技术的飞速发展，高速大规模集成电路的广泛应用，高速系统的设计也越来越受到重视，高速系统与低速系统的PCB设计有很大不同。本文从实际设计的角度介绍了高速系统中电源、接地、时钟电路、过孔等的设计和需要注意的问题。     

虚拟标准显色设备——跨网络色彩重现的新方案

随着网络的普及和多媒体应用的增长,彩色的传输和真实重现日益受到重视.虽然基于ICC的色彩管理提供了色彩复制与传递机制,但是这些技术仍存在增加系统开销、设备特性信息传递困难、不同色彩管理系统难以混合等问题.本文提出了"虚拟标准显色设备"的概念,较好地解决了跨网络、跨平台的色彩重现问题.实验结果证明了这种方法的有效性.     

大口径光学元件波前调制PSD模拟分析

 使用PSD作为大口径光学元件表面加工质量的评价参数，针对不同的波前调制进行了初步的模拟计算，得到了不同调制频率和不同调制深度情况下的PSD曲线变化情况。当调制频率不同时，PSD曲线的突变部分会发生相应的频移，调制频率高则突变发生在空间频率较高的频段，同时PSD峰值不变。相对应调制深度不同时，PSD曲线的突变部份峰值发生变化，调制深度大则峰值大，与此同时峰值出现的位置不会发生变化。计算和分析结果表明PSD分析结果能够在频率域反应出元件表面受到的不同程度的调制信息。     

电爆炸箔断路开关的理论和实验研究

 采用金属箔电爆炸过程的二维数值计算模型，对含电爆炸金属箔断路开关的电感储能脉冲功率调节系统进行了数值计算。以此为基础，研制出了一种低电感型的电爆炸箔断路开关，并以4μF/75kV脉冲电容器组作为初级能源，13Ω电阻作为负载进行实验研究。研究结果表明：在负载上可获得约250kV，脉宽大于400ns的脉冲电压。     

强流射频四极加速器输入耦合环的物理设计研究

 详细讨论了强流射频四极加速器高频输入耦合环的一些基本问题，完成了高频输入耦合环的初步物理设计. 利用二维程序Superfish 的一些结果，确定了耦合环的大小，计算了耦合环的功耗，并对构成耦合环导线的粗细进行了估算。该耦合环的物理设计可作为耦合环试验的基础，同时，也可作为三维程序HFSS 模拟计算的起点。     

FPGA-based test bed for measurement of AM/AM and AM/PM distortion and modeling memory effects in RF PAs

Using a field-programmable gate array (FPGA) development board, a digital signal processor (DSP) builder, and the phase-to-amplitude conversion principle, a low-cost system for measuring the amplitude-to-amplitude (AM/AM) and amplitude-to-phase (AM/PM) distortion curves of radio frequency (RF) power amplifiers (PAs) is presented. The state of the art based on the measurements and preliminary studies of AM/AM and AM/PM distortion curves is discussed. A full digital control of the test bed simulated/emulated in Matlab/Simulink is introduced to recalculate the known AM/AM and AM/PM measurements stored as look-up table (LUT). Finally, the low-cost system comprises the memory polynomial model (MPM) that involves the nonlinearity order and memory effects of real PAs.     

油色谱在线监测装置在换流站中的应用及运维管理

文中论述了油色谱在线监测装置在换流站状态检修中的应用、油色谱在线监测技术的原理、油色谱在线监测装置的维护管理和存在的问题,及其相关技术展望。     

基于重叠式联盟博弈的Femtocell干扰管理研究

给出了一种基于重叠式联盟形成博弈论的协作式算法,用于解决正交频分多址宏小区和家庭基站(Femtocell)两层网络中的资源分配和干扰管理问题。给出的算法相比于已有算法显著降低了家庭基站接入点到家庭基站用户的下行同层干扰,提高了以系统码率衡量的系统性能。     

Reliability of Cu nanoparticle joint for high temperature power electronics

Power cycle reliability of Cu nanoparticle joint has been studied for high temperature operation of power devices. Al₂O₃ heater chips and Cu–65 wt% Mo baseplates were joined by Cu nanoparticles and Sn–0.7Cu and power cycle tests of 65/200 °C and 65/250 °C were carried out on the joints. The Cu nanoparticles were prepared by reducing Cu carbonate in ethylene glycol with dodecanoic acid + dodecyl amine (C12) and decanoic acid and decyl amine (C10) as capping agents. A power cycle test of 65/200 °C did not inflict severe damage on the Cu nanoparticle joints so that there were not many cracks formed after 3000 cycles. Vertical cracks were formed in the C12 Cu nanoparticle joint after 3000 cycles of 65/250 °C test, however the maximum temperature during the power cycle test did not change at all because vertical cracks did not have an effect on preventing heat flow. On the contrary, lateral cracks were completely formed in the Sn–0.7Cu soldered joint after 200 cycles of 65/200 °C test and in the C10 Cu nanoparticle joint after 360 cycles of 65/250 °C test. In these experiments, the maximum temperatures were rapidly increased because heat conduction was prevented across the formed lateral cracks.