Sol-Gel Preparation and Photoelectrochemical Properties of Fe2TiO5 Thin Films

Polycrystalline Fe₂TiO₅ films were prepared on nesa silica glass substrates by the sol-gel method, and their photoanodic properties were measured in a three-electrode wet cell with an aqueous buffer solution of pH = 7. Gel films were crystallized into Fe₂TiO₅ when fired at 500°C. The photoanodic current significantly increased when the films were fired at 700°C, and then decreased with increasing firing temperature. Thicker films obtained by repeating the gel film deposition and firing showed smaller photocurrent, and the 50 nm thick film prepared via non-repetitive deposition exhibited the maximum photocurrent. Although the photoresponse was extended to wavelengths near 500 nm, the maximum quantum yield was as low as 0.12 at a wavelength of 340 nm.     

Perfluorinated polymer surfaces comprising SF5-terminated long-chain perfluoroacrylate

A new perfluorinated acrylate monomer containing the SF₅(CF₂)₆-perfluorinated side chain was synthesized and polymerized into films. Bulk monomer characterization is consistent with the molecular structure based on FTIR, mass spectrometry and NMR analyses. The surface properties of polymer coatings were studied with aqueous wetting (contact angle) and X-ray photoelectron spectroscopy (XPS) methods. The surface composition is shown to be highly enriched in the terminal side chain SF₅-chemistry and exhibits properties consistent with a highly apolar, non-wetting perfluorinated polymer surface. Depth-dependent XPS studies using angular-resolved methods (ADXPS) confirmed a non-stoichiometric enrichment of sulfur and fluorine at the film ambient interface, consistent with a surface presence of the terminal SF₅-group and possibly film structural anisotropy in the surface zone. Time-of-flight (TOF) secondary ion mass spectrometry (SIMS) analysis supplements the XPS data by showing the presence of all expected SF₅-acrylate chemistry components in the outer 15 Å of the film surface.     

Carbon film growth on iron substrates by a CVD method

Carbon film coatings have been produced by a hot‐wall chemical vapor deposition (CVD) method under moderate conditions from pyrolysis of a mixture of propane and argon on an Fe(110) substrate at temperatures of 800–900 °C for different deposition times. The effects of temperature and reaction time on the growth of the carbon films were studied. Field‐emission scanning electron microscopy (FESEM), Raman microscopy, Auger electron spectroscopy (AES) and x‐ray diffraction methods have been performed to study the surface morphologies, growth features and microstructures of the carbon film coatings. The FESEM analyses indicated that carbon films on an Fe substrate consisted of flat‐layer and filamentous morphologies. Raman and AES analyses showed that the carbon initially was crystalline but the degree of disorder in the top layer of the carbon film increased with increasing deposition temperature. High‐resolution transmission electron microscopy studies are also in agreement with Raman results. The same trend was observed when the deposition time was increased from 5 to 30 min. Copyright © 2005 John Wiley & Sons, Ltd.     

2,5-二(2-菲基)-[3,2-b]并二噻吩的合成、表征及在有机薄膜晶体管中的应用

本文合成了2,5-二(2-菲基)-[3,2-b]并二噻吩(PhTT), 表征了其基本的物理和化学性质, 制备了相应的有机薄膜晶体管.     

血红素LB膜的电化学行为

采用循环伏安法研究了血红素与脑磷脂混合Y型LB（Langmuir-Blodgett）膜在玻碳电极上的电化学行为，结果表明血红素LB膜有良好的电化学活性，在0．1mol/L KCl溶液中有一对氧化还原峰（－0．42V／－0．30V）；将血红素LB膜转移到玻碳电极表面得到的血红素LB膜修饰电极（heme LB-GC）对溶液中溶解氧的电化学还原有良好的催化作用，其催化还原过程具有不可逆电荷传递特性。     

Mercury-free sono-electroanalytical detection of lead in human blood by use of bismuth-film-modified boron-doped diamond electrodes

We report the electroanalytical determination of lead by anodic stripping voltammetry at in-situ-formed, bismuth-film-modified, boron-doped diamond electrodes. Detection limits in 0.1 mol L^–1 nitric acid solution of 9.6x10^–8 mol L^–1 (0.2 ppb) and 1.1x10^–8 mol L^–1 (2.3 ppb) were obtained after 60 and 300 s deposition times, respectively. An acoustically assisted deposition procedure was also investigated and found to result in improved limits of detection of 2.6×10^–8 mol L^–1 (5.4 ppb) and 8.5×10^–10 mol L^–1 (0.18 ppb) for 60 and 300 s accumulation times, respectively. Furthermore, the sensitivity obtained under quiescent and insonated conditions increased from 5.5 (quiescent) to 76.7 A mol^–1 L (insonated) for 60 s accumulation and from 25.8 (quiescent) to 317.6 A mol^–1 L (insonated) for 300 s accumulation. Investigation of the use of ultrasound with diluted blood revealed detection limits of the order of 10^–8 mol L^–1 were achievable with excellent inter- and intra-reproducibility and sensitivity of 411.9 A mol^–1 L . For the first time, electroanalytical detection of lead in diluted blood is shown to be possible by use of insonated in-situ-formed bismuth-film-modified boron-doped diamond electrodes. This method is a rapid, sensitive, and non-toxic means of clinical sensing of lead in whole human blood.     

Electron microscopic phase analysis of BN-thin films

A series of BN films was deposited by means of r.f. magnetron sputtering of a h-BN target onto Si(1OO) surfaces. Hereby, the substrate bias voltage was varied. Special interest is focussed to the influence of the deposition parameters on the orientation of the growing hexagonal BN film with respect to the substrate. For structural investigation, cross section samples were prepared. In addition to HRTEM and diffraction investigations, especially electron energy loss spectroscopy (EELS) was applied successfully for phase identification. For negative bias voltages of U _B =–300 V and U _B =–350V, we found a phase system consisting of a first-grown 25 nm thick layer of hexagonal structure with the c axis parallel to the substrate surface followed by the cubic phase.Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthday     

Preparation and Characterization of Mixed‐Valent Nickel Oxide/Nickel Hexacyanoferrate Hybrid Films and Their Electrocatalytic Properties

Polynuclear mixed‐valent nickel oxide and nickel hexacyanoferrate hybrid film was prepared on glassy carbon electrode by multiple scan cyclic voltammetry. The film growth was monitored using electrochemical quartz crystal microbalance (EQCM). The cyclic voltammogram of the nickel hexacyanoferrate film is characterized by single redox couple whereas nickel oxide/nickel hexacyanoferrate hybrid film exhibits two redox couples. Cyclic voltammetric features suggest that the charge transfer process in both films resembles that of surface‐confined redox species. In stronger basic solution (pH ≥9), nickel hexacyanoferrate film was gradually converted into nickel oxide film during potentiodynamic cycling. The peak potential of nickel oxide redox couple moved into more negative side with increasing pH of contacting solution whereas the peak potential of nickel hexacyanoferrate redox couple remains the same. Electrocatalytic behavior of hybrid film coated electrodes toward ascorbic acid, hydrazine and hydroxylamine was investigated using cyclic voltammetry technique. Analytical application of nickel oxide/nickel hexacyanoferrate hybrid film electrode was tested in amperometry and flow injection analysis.     

Electron Probe Microanalysis of HfO2 Thin Films on Conductive and Insulating Substrates

Quantitative electron probe microanalysis of highly insulating materials is a complicated problem, partially solved by coating samples with grounded thin conductive layers or using novel scanning electron microscopy (SEM) techniques, such as low-voltage and/or variable pressure SEM. In this work, some problems of quantitative X-ray microanalysis of thin HfO₂ films, in particular the possibility to determine mass thickness correlated to the density of the layer material, are discussed. For comparison, Al₂O₃, Ta₂O₅ and TiO₂ films grown onto both semiconductive Si and insulating quartz substrates were also analysed. All the films studied were synthesized by atomic layer deposition method.     

Effect of monomer concentration on characteristics of methacrylic acid-grafted polyethylene film prepared by photografting

The effect of monomer concentration on photografting of methacrylic acid (MAA) onto linear low-density polyethylene (PE) film (thickness=30 μm) was investigated at 60 °C in water solvent together with the location of MAA-grafted chains. Xanthone was used as a photoinitiator which was coated on the film sample earlier. The higher percentage of grafting and graft efficiency were afforded for the system with the higher monomer concentration. The resultant MAA-grafted films were subjected to measurements of pH-responsive character and ability to adsorb cupric ion in order to understand the characteristics of function introduced. The grafted samples exhibited the pH-responsive character, where they shrank and swelled in acidic and alkaline media, respectively. The pH-responsive character of the grafted films was higher for the samples prepared in the system with a higher monomer concentration. Moreover, the grafted samples exhibited the ability to adsorb cupric ion, and the ability was reduced when the sample was prepared in the system with a higher monomer concentration. The different extents of the pH-responsive character and ability to adsorb cupric ion of the resulting grafted PE films were discussed in terms of location of grafted chains in the film substrate, which was determined by a scanning electron microscope and an attenuated total reflection infrared spectroscopy.